3DMark Vantage Compilation

[Deleted member 74752]

What are you using to overclock the card?

MSI Afterburner...acting kinda flakey too. Values don't read the same as in gpu-z and can hardly move memory. You folks use Precision?

 

[Techtu]

just pushed another 500mhz out each core on my processor, from 3.6Ghz to 4.1Ghz and I could only beat my old score by 200 point's .... That's depressing

 

[JrRacinFan]

MSI Afterburner...acting kinda flakey too. Values don't read the same as in gpu-z and can hardly move memory. You folks use Precision?

May want to rma that card sooner than later. I'm on Afterburner also without issue and can run 890/1000 @ 1.087 daily. Max load temp 62C with auto fan.

just pushed another 500mhz out each core on my processor, from 3.6Ghz to 4.1Ghz and I could only beat my old score by 200 point's

Which driver set?

 

[(FIH) The Don]

thats pretty low for that 460, its supposed to be one of the best cards out there, even MSI claims it to be

what are you using for oc? and what voltage

 

[Techtu]

Which driver set?

thats pretty low for that 460, its supposed to be one of the best cards out there, even MSI claims it to be

what are you using for oc? and what voltage

Here's pretty much what your asking for atm.

as mentioned CPU is at 4.1Ghz. (but barely any point difference from 3.6Ghz).

 

[JrRacinFan]

Here's pretty much what your asking for atm.
http://img.techpowerup.org/100921/Capture076.jpg

as mentioned CPU is at 4.1Ghz. (but barely any point difference from 3.6Ghz).

Migrate over to 260.63's. I love these new drivers.

 

[Techtu]

Migrate over to 260.63's. I love these new drivers.

I'll give them a go shortly...

p.s I hate how your i3 pwn's my 1055T in 06

 

[Deleted member 74752]

What a pos set-up...I feel like I'm dealing with ATI all over again. PhysX on, cpu at defaults, Afterburner does not apply all the settings.

Second run I had to use Afterburner for volts and Precision to set the clocks...geeez

Latest version of Afterburner will not install for me without error.

 

[Asylum]

What a pos set-up...I feel like I'm dealing with ATI all over again. PhysX on, cpu at defaults, Afterburner does not apply all the settings.

Second run I had to use Afterburner for volts and Precision to set the clocks...geeez

Latest version of Afterburner will not install for me without error.

You got some kind of driver issue going on there.
Try sweeping your display driver registery and reinstalling.

 

[Deleted member 74752]

Have done that and everything else at least twice. Now no version of Afterburner will give voltage control. Also just tried the latest beta driver to no effect.

 

[Deleted member 74752]

In the morning I will try it in another pc with a different OS...if that doesnt get it going it's back to the egg for this turd monkey.

 

[Techtu]

Have done that and everything else at least twice. Now no version of Afterburner will give voltage control. Also just tried the latest beta driver to no effect.

Curious... have you gone into the settings and selected the box that enable's you to over-volt your card?

EDIT: Dude you've made over a 1000 post's... you surely should know to edit a post rather than post one after another.

 

[Wile E]

just pushed another 500mhz out each core on my processor, from 3.6Ghz to 4.1Ghz and I could only beat my old score by 200 point's .... That's depressing

Vantage isnt very cpu dependent, especially if you have Physx enabled. Going from 3600 to 4455 on my old QX was only worth like 150pts with physx enabled on my 8800GT's.

 

[dj-electric]

allll the power 400$ can buy

 

[Deleted member 74752]

Afterburner is a total failure here...no voltage control whatsoever. Nvidia Inspector does allow it to some extent. I have a modded bios that I will flash that will allow unlimited voltage control. Follows is a short run I did today with Nvidia Inspector only...

rickss69|MSI Twin FrozrII GTX 460|907/1051/1813|20430|Intel 980X @ 4499MHz

 

[DOM]

Afterburner is a total failure here...no voltage control whatsoever. Nvidia Inspector does allow it to some extent. I have a modded bios that I will flash that will allow unlimited voltage control. Follows is a short run I did today with Nvidia Inspector only...

rickss69|MSI Twin FrozrII GTX 460|907/1051/1813|20430|Intel 980X @ 4499MHz

your still running those settings

i used this to flash my nivida cards 8500/8600/GT/GTS Mod guide...

 

[Deleted member 74752]

your still running those settings

i used this to flash my nivida cards 8500/8600/GT/GTS Mod guide...

They were a winner once, right?

Not doing to shabby over here either... http://hwbot.org/competition/msi_hunt_450_460

 

[(FIH) The Don]

(FIH) The Don|Gainward GTX 470+GT240|805/905/1610|20915|C2Q 9550 @ 4100Mhz

yes with PhysX, wanted to test the 240 for that

 

[2DividedbyZero]

2DividedByZero|Sapphire HD5970|935/1250|P33908|980x @ 4.2GHz

 

[fullinfusion]

fullinfusion|Sapphire oc 5970 - 8800GT PhysX|900/1200|28823|PII X6@4.11Ghz

 

[JrRacinFan]

Update
JrRacinFan|EVGA GTX 460| 910/1820/1005 | 18836 | Intel Core i3 530 @ 4.4Ghz

 

[MetalRacer]

MetalRacer|Asus HD5850 Xfire|965/1340|35065|i7 980X @ 4522 MHz

 

[MetalRacer]

MetalRacer|Asus HD5850 Xfire - GT220 PhysX|965/1340|36555|i7 980X @ 4522 MHz

 

[20mmrain]

Update
JrRacinFan|EVGA GTX 460| 910/1820/1005 | 18836 | Intel Core i3 530 @ 4.4Ghz
http://img.techpowerup.org/100925/Capture051.jpg

Nice new score bro!!!

 

[20mmrain]

Sorry for the double post... but I am still on the way up.... Not finished yet but a little run Here yah go

20mmrain|EVGA GTX 460 SC 768MB SLI|905/1810/1001|32212| i7 860@4.0Ghz

Pretty sure I can get to 33K or 34K now