• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Opteron 185 IHS Removal! + pics :) :)

Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Hi all! well, getting a bit annoyed at the crappy stepping on my 185 opty and resulting temperatures, i decided to remove the Integrated Heat Spreader (IHS) and fix the peltier waterblock directly to the die's durface. :eek:

Right, First of all i cleared my desk and got a decent work surface, then I collected the tools to butcher my cpu into submission :slap:

Razer blades removed from shaving razors, to be used to cut around the IHS cap glue, a stanly knife for popping the cap off at the end of the process, solvent for cleaning off the thermal gunk, black foam pad for protecting the CPU's pins, Coollabs Liquid Metal thermal compound and cotton swabs for spreading this on the Silicone Die.



Below pic shows the recently extracted Opteron 185 CPU still coated with liquid pro



Here is a close up of the cleaned CPU showing the stepping as LCBBE



I started by taking the shaving razors and cutting into each othe the processors corners, using gentle rocking motions, carefully feeling for any internal component contact. I then used the razors corner to slice along the sides on the IHS. I also used a cotton swab to add some solvent to help loosed the glue holding the IHS onto the pcb. After going around the CPU as best i could,I used the stanly knife to wedge along the length of the cpu and prise open the cap



Here is the processor without the IHS attached. You can clearly see the thermal gunk on the die, I also noted how heavy the IHS was, and how thick it was, a good 3mm of solid metal. Ouch.



Heres a close up of the CPU die all nice and shiny after a jolly good cleaning using solvent and swabs



And finally, here it is again, but with the liquid metal applied to the die :toast:



I had to slightly modify the cpu retention bracked to accomodate for the 3mm gap after IHS removal. But booted to windows at stock frequencies to my relief, it appears to have worked!! Phew! :rockout: :rockout: :rockout:

Now my plan is to test against previous overclock tests and see how much (if any) I have knocked off the peak temperatures.

Yeay for not killing my CPU :toast:

I will update as I find out how well this has worked for overclocking
 
Joined
Apr 23, 2006
Messages
3,558 (0.54/day)
Location
Enschede, The Netherlands
System Name Lian Li Carbon fiber ed.
Processor Intel i5 2500k 4.6Ghz 24/7 Max OC 5Ghz
Motherboard Asrock Z68 Extreme3 Gen3
Cooling Swiftech blocks, 360 Xflow rad, Swiftech 120 rad, Liang with XSPC res/pump top.
Memory 8Gb Mushkin 1600Mhz 8-9-8-24
Video Card(s) Sapphire HD6950 2Gb
Storage OCZ Vertex 4 128 / Western Digital 160
Display(s) ASUS 25,5" wide VW266h
Power Supply Corsair HX620 modular
Software Windows 7 64
Once i get my new system running i'm gonna give it a go on my 3700. And try to get to 3.0 or higher.:D

Nice job btw.
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Cheerz, apparently sum peeps have got 20C drop in load temps on single core AMD's, however, be bleedin careful, one of those surface mount components could easily be lopped off, and Id hate to hear that happened :(

Quoted from overclockersclub.com:

"For my 3500+, I had temperature problems with the IHS on. My load temps soared in excess of 65°C even with moderate vcore values, and a confirmed perfect AS5 application.

3500+ Venice with Thermalright SLK-948u and Vantec Tornado 92mm

Before (idle/load): 44°C / >65°C
After (idle/load): 35°C / 43°C"
 

Wile E

Power User
Joined
Oct 1, 2006
Messages
24,318 (3.81/day)
System Name The ClusterF**k
Processor 980X @ 4Ghz
Motherboard Gigabyte GA-EX58-UD5 BIOS F12
Cooling MCR-320, DDC-1 pump w/Bitspower res top (1/2" fittings), Koolance CPU-360
Memory 3x2GB Mushkin Redlines 1600Mhz 6-8-6-24 1T
Video Card(s) Evga GTX 580
Storage Corsair Neutron GTX 240GB, 2xSeagate 320GB RAID0; 2xSeagate 3TB; 2xSamsung 2TB; Samsung 1.5TB
Display(s) HP LP2475w 24" 1920x1200 IPS
Case Technofront Bench Station
Audio Device(s) Auzentech X-Fi Forte into Onkyo SR606 and Polk TSi200's + RM6750
Power Supply ENERMAX Galaxy EVO EGX1250EWT 1250W
Software Win7 Ultimate N x64, OSX 10.8.4
Since you're using pelt, how do you waterproof the exposed components?

You may have also given me the balls to try this on my Brisbane when it gets here, but only if I can't hit the 3.2Ghz I'm after.
 

p-jack

New Member
Joined
Jul 13, 2006
Messages
333 (0.05/day)
Location
Arheilgen
System Name Ironjack
Processor AMD Opteron 165 @ 2,4GHz, stock voltage
Motherboard Asus A8N-E (nForce4 Ultra)
Cooling Scythe Infinity, Thermalright HR-05SLI, AC AcceleroX1Rev.2
Memory 2x1024MB Patriot PC3200 @ 2,5-4-4-8
Video Card(s) Powercolor X1900XT 512MB @ stock clocks
Storage 320GB Seagate ST3320620AS, 160GB Samsung HD160JJ
Display(s) BenQ FP91GX 19" TFT
Case Coolermaster Centurion 534
Audio Device(s) Realtek ALC850 (onboard)
Power Supply Coolermaster iGreen 430W
Software Ubuntu 6.10 + Windoofs XP
nice job indeed! :toast:
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Since you're using pelt, how do you waterproof the exposed components?

Gonna be running at above ambient temps atm, but getting some dielectric grease to coat the components in soon --> tho saying that, the gap and those components are sealed tight within a confined compartment, no additional moisture can possibly get in, so im probs ok for now

But, also the whole assembly is tightly sealed in neoprene
 
Last edited:
Joined
Feb 19, 2006
Messages
6,270 (0.95/day)
Location
New York
Processor INTEL CORE I9-9900K @ 5Ghz all core 4.7Ghz Cache @1.305 volts
Motherboard ASUS PRIME Z390-P ATX
Cooling CORSAIR HYDRO H150I PRO RGB 360MM 6x120mm fans push pull
Memory CRUCIAL BALLISTIX 3000Mhz 4x8 32gb @ 4000Mhz
Video Card(s) EVGA GEFORECE RTX 2080 SUPER XC HYBRID GAMING
Storage ADATA XPG SX8200 Pro 1TB 3D NAND NVMe,Intel 660p 1TB m.2 ,1TB WD Blue 3D NAND,500GB WD Blue 3D NAND,
Display(s) 50" Sharp Roku TV 8ms responce time and Philips 75Hz 328E9QJAB 32" curved
Case BLACK LIAN LI O11 DYNAMIC XL FULL-TOWER GAMING CASE,
Power Supply 1600 Watt
Software Windows 10
4th picture take a good look cuz the 3F3E3D3s now have your (thumb finger) print:ohwell:
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
4th picture take a good look cuz the 3F3E3D3s now have your (thumb finger) print:ohwell:

yeah, well i gotta hold it somehow :p, suppose for the pic i shoulda cleaned it but i was taking pics as I went so didnt really think of that, and well im not all that paranoid hehe
 
Last edited:
Joined
Apr 23, 2006
Messages
3,558 (0.54/day)
Location
Enschede, The Netherlands
System Name Lian Li Carbon fiber ed.
Processor Intel i5 2500k 4.6Ghz 24/7 Max OC 5Ghz
Motherboard Asrock Z68 Extreme3 Gen3
Cooling Swiftech blocks, 360 Xflow rad, Swiftech 120 rad, Liang with XSPC res/pump top.
Memory 8Gb Mushkin 1600Mhz 8-9-8-24
Video Card(s) Sapphire HD6950 2Gb
Storage OCZ Vertex 4 128 / Western Digital 160
Display(s) ASUS 25,5" wide VW266h
Power Supply Corsair HX620 modular
Software Windows 7 64
Yeah they are looking as we speak.:roll:
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Sweeet! Ive made some progress :) slowly working my way up the Mhz..

Ok, previously I was testing for stability.. needed
->1.325 Volts to get 2882Mhz @ 28/25C temp under load
now:
->1.3 Volts to get 2926Mhz @ 19/9C under load!!!

thats quite a drop in temperatures imo :) hopefully as I keep pumping volts across and raising the frequency ill get better results.

Keep ya all updated
 
Joined
Feb 19, 2006
Messages
6,270 (0.95/day)
Location
New York
Processor INTEL CORE I9-9900K @ 5Ghz all core 4.7Ghz Cache @1.305 volts
Motherboard ASUS PRIME Z390-P ATX
Cooling CORSAIR HYDRO H150I PRO RGB 360MM 6x120mm fans push pull
Memory CRUCIAL BALLISTIX 3000Mhz 4x8 32gb @ 4000Mhz
Video Card(s) EVGA GEFORECE RTX 2080 SUPER XC HYBRID GAMING
Storage ADATA XPG SX8200 Pro 1TB 3D NAND NVMe,Intel 660p 1TB m.2 ,1TB WD Blue 3D NAND,500GB WD Blue 3D NAND,
Display(s) 50" Sharp Roku TV 8ms responce time and Philips 75Hz 328E9QJAB 32" curved
Case BLACK LIAN LI O11 DYNAMIC XL FULL-TOWER GAMING CASE,
Power Supply 1600 Watt
Software Windows 10

sipha

New Member
Joined
Apr 27, 2007
Messages
12 (0.00/day)
Location
U.K
Processor E6600 @ 4.4Ghz
Motherboard P5B Deluxe WiFi
Cooling Custom Phase change unit Chilly1 Extreme XE
Memory 2Gb Crucial Ballistix DDR2 PC6400 4.4.4.12
Video Card(s) 8800 GTS 320Mb
Storage 2x WD 160Gb 16Mb Cache 7200rpm Caviar's
Display(s) Iiyama 19" TFT
Case Lian-Li PC-7 Plus
Power Supply Corsair HX520w
Nice job ! Somthing I've not been brave enough to try as of yet :eek:
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Nice job ! Somthing I've not been brave enough to try as of yet :eek:

lol, im sure youd get a killer result if you did, esp if running at 4.4Ghz, actually, then again ur on phase aint you? so either way it would be chilly :)
 

KillZone

New Member
Joined
Mar 29, 2007
Messages
57 (0.01/day)
I've done two 3500+ venice cores. Works great and I saw a large temp drop with the water setup. As long as your slow and careful its not that hard. Also have to be careful not to bend the pins.

Have to make sure that your heatsink is touching the top of the core though with the extra gap where the IHS used to be. I usually check it once with some paste and just pull it off to make sure it has full contact.

I did burn up one processor because of that mistake:(
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
I've done two 3500+ venice cores. Works great and I saw a large temp drop with the water setup. As long as your slow and careful its not that hard. Also have to be careful not to bend the pins.

Have to make sure that your heatsink is touching the top of the core though with the extra gap where the IHS used to be. I usually check it once with some paste and just pull it off to make sure it has full contact.

I did burn up one processor because of that mistake:(

yeah, had to cut some spacer brackets on the pelt block to get proper contact, or im certain id have boiled my cores haha, well i can laugh now coz its all over and done with :) i bent 1 pin, but it was only slightly and easily fixed.
What sort of temps did u end up with btw?
 

Kursah

Super Moderator
Staff member
Joined
Oct 15, 2006
Messages
14,666 (2.30/day)
Location
Missoula, MT, USA
System Name Kursah's Gaming Rig 2018 (2022 Upgrade) - Ryzen+ Edition | Gaming Laptop (Lenovo Legion 5i Pro 2022)
Processor R7 5800X @ Stock | i7 12700H @ Stock
Motherboard Asus ROG Strix X370-F Gaming BIOS 6203| Legion 5i Pro NM-E231
Cooling Noctua NH-U14S Push-Pull + NT-H1 | Stock Cooling
Memory TEAMGROUP T-Force Vulcan Z 32GB (2x16) DDR4 4000 @ 3600 18-20-20-42 1.35v | 32GB DDR5 4800 (2x16)
Video Card(s) Palit GeForce RTX 4070 JetStream 12GB | CPU-based Intel Iris XE + RTX 3070 8GB 150W
Storage 4TB SP UD90 NVME, 960GB SATA SSD, 2TB HDD | 1TB Samsung OEM NVME SSD + 4TB Crucial P3 Plus NVME SSD
Display(s) Acer 28" 4K VG280K x2 | 16" 2560x1600 built-in
Case Corsair 600C - Stock Fans on Low | Stock Metal/Plastic
Audio Device(s) Aune T1 mk1 > AKG K553 Pro + JVC HA-RX 700 (Equalizer APO + PeaceUI) | Bluetooth Earbuds (BX29)
Power Supply EVGA 750G2 Modular + APC Back-UPS Pro 1500 | 300W OEM (heavy use) or Lenovo Legion C135W GAN (light)
Mouse Logitech G502 | Logitech M330
Keyboard HyperX Alloy Core RGB | Built in Keyboard (Lenovo laptop KB FTW)
Software Windows 11 Pro x64 | Windows 11 Home x64
Now to see if someone's got the kahonas to try this on a core2 processor! I haven't seen any pics of them with the IHS off...but that could also be interesting...or horrible! Good job man, looks to be worth the work!
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Now to see if someone's got the kahonas to try this on a core2 processor! I haven't seen any pics of them with the IHS off...but that could also be interesting...or horrible! Good job man, looks to be worth the work!

yeah id like to see some naked Core2 duo action ;) id imagine that would get you one hellova good overclock, since intel chips seem to oc better than most dual core AMD's, well i think anyways
 

Wile E

Power User
Joined
Oct 1, 2006
Messages
24,318 (3.81/day)
System Name The ClusterF**k
Processor 980X @ 4Ghz
Motherboard Gigabyte GA-EX58-UD5 BIOS F12
Cooling MCR-320, DDC-1 pump w/Bitspower res top (1/2" fittings), Koolance CPU-360
Memory 3x2GB Mushkin Redlines 1600Mhz 6-8-6-24 1T
Video Card(s) Evga GTX 580
Storage Corsair Neutron GTX 240GB, 2xSeagate 320GB RAID0; 2xSeagate 3TB; 2xSamsung 2TB; Samsung 1.5TB
Display(s) HP LP2475w 24" 1920x1200 IPS
Case Technofront Bench Station
Audio Device(s) Auzentech X-Fi Forte into Onkyo SR606 and Polk TSi200's + RM6750
Power Supply ENERMAX Galaxy EVO EGX1250EWT 1250W
Software Win7 Ultimate N x64, OSX 10.8.4
Seeing you do this is making me seriously debate doing it to my Brisbane that's due in later today.
 
Joined
Apr 23, 2006
Messages
3,558 (0.54/day)
Location
Enschede, The Netherlands
System Name Lian Li Carbon fiber ed.
Processor Intel i5 2500k 4.6Ghz 24/7 Max OC 5Ghz
Motherboard Asrock Z68 Extreme3 Gen3
Cooling Swiftech blocks, 360 Xflow rad, Swiftech 120 rad, Liang with XSPC res/pump top.
Memory 8Gb Mushkin 1600Mhz 8-9-8-24
Video Card(s) Sapphire HD6950 2Gb
Storage OCZ Vertex 4 128 / Western Digital 160
Display(s) ASUS 25,5" wide VW266h
Power Supply Corsair HX620 modular
Software Windows 7 64
The thing i am most sared of is crushing the core when placing the cooler.:eek:
 
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
The thing i am most sared of is crushing the core when placing the cooler.:eek:

as long as you DONT apply uneven pressure the die can take many many pounds of crush pressure, however, not trying to put u off, but slight uneven pressure and theres a chance the die will snap or crack :eek: :eek: got my pelt block TIGHT,actually probs tighter than i intended, but i tightened each screw a few turns alternating over about 5-10 minutes, lol my arm was sore after hehe


BTW, check out this site, will give tips for getting the IHS off and modifying amd retention brackets, (which may also apply to Intel) to compensate for loss of cpu height:

http://www.overclockersclub.com/guides/a64-ihs-removal.php

I did hear on older Intel chips they bonded the IHS to the chip, and taking it off could, erm, take off the die, which would be particularly awful...
 
Last edited:
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Seeing you do this is making me seriously debate doing it to my Brisbane that's due in later today.

Hay mate what cooler you gonna use on that chip?
 
Joined
Apr 23, 2006
Messages
3,558 (0.54/day)
Location
Enschede, The Netherlands
System Name Lian Li Carbon fiber ed.
Processor Intel i5 2500k 4.6Ghz 24/7 Max OC 5Ghz
Motherboard Asrock Z68 Extreme3 Gen3
Cooling Swiftech blocks, 360 Xflow rad, Swiftech 120 rad, Liang with XSPC res/pump top.
Memory 8Gb Mushkin 1600Mhz 8-9-8-24
Video Card(s) Sapphire HD6950 2Gb
Storage OCZ Vertex 4 128 / Western Digital 160
Display(s) ASUS 25,5" wide VW266h
Power Supply Corsair HX620 modular
Software Windows 7 64
Thanks for the link. I watched that about a year back. Since then i always want to do it.:)
 

Wile E

Power User
Joined
Oct 1, 2006
Messages
24,318 (3.81/day)
System Name The ClusterF**k
Processor 980X @ 4Ghz
Motherboard Gigabyte GA-EX58-UD5 BIOS F12
Cooling MCR-320, DDC-1 pump w/Bitspower res top (1/2" fittings), Koolance CPU-360
Memory 3x2GB Mushkin Redlines 1600Mhz 6-8-6-24 1T
Video Card(s) Evga GTX 580
Storage Corsair Neutron GTX 240GB, 2xSeagate 320GB RAID0; 2xSeagate 3TB; 2xSamsung 2TB; Samsung 1.5TB
Display(s) HP LP2475w 24" 1920x1200 IPS
Case Technofront Bench Station
Audio Device(s) Auzentech X-Fi Forte into Onkyo SR606 and Polk TSi200's + RM6750
Power Supply ENERMAX Galaxy EVO EGX1250EWT 1250W
Software Win7 Ultimate N x64, OSX 10.8.4
Joined
Aug 12, 2006
Messages
3,278 (0.51/day)
Location
UK-small Village in a Valley Near Newcastle
Processor I9 9900KS @ 5.3Ghz
Motherboard Gagabyte z390 Aorus Ultra
Cooling Nexxxos Nova 1080 + 360 rad
Memory 32Gb Crucial Balliastix RGB 4.4GHz
Video Card(s) MSI Gaming X Trio RTX 3090 (Bios and Shunt Modded) 2.17GHz @ 38C
Storage NVME / SSD RAID arrays
Display(s) 38" LG 38GN950-B, 27" BENQ XL2730Z 144hz 1440p, Samsung 27" 3D 1440p
Case Thermaltake Core series
Power Supply 1.6Kw Silverstone
Mouse Roccat Kone EMP
Keyboard Corsair Viper Mechanical
Software Windows 10 Pro
Overclock results

Hell yeah!!!!!! :rockout: :rockout: :rockout:

removing the IHS has made a universe of difference, and im still just in the middle of overclocking

Previously, i needed 1.55-1.6V to get around 3Ghz overclock, which resulted under load of temperatures around 60/65 on core0 and 50ish on Core1

Now: :) at just 1.25V i can get a whopping 2970Mhz oc

and the load temperatures are shown in the core temp pic below



a huge 35ish Degree C drop in temperatures on core0 and 33ish drop on core1 under load for a similar overclock, thats just insane!!!
I therefore have major headroom for further overclocking (i hope) especially with those temperatures. damn, now if i had done this on my previous better stepping 185 opty...
 
Joined
Apr 23, 2006
Messages
3,558 (0.54/day)
Location
Enschede, The Netherlands
System Name Lian Li Carbon fiber ed.
Processor Intel i5 2500k 4.6Ghz 24/7 Max OC 5Ghz
Motherboard Asrock Z68 Extreme3 Gen3
Cooling Swiftech blocks, 360 Xflow rad, Swiftech 120 rad, Liang with XSPC res/pump top.
Memory 8Gb Mushkin 1600Mhz 8-9-8-24
Video Card(s) Sapphire HD6950 2Gb
Storage OCZ Vertex 4 128 / Western Digital 160
Display(s) ASUS 25,5" wide VW266h
Power Supply Corsair HX620 modular
Software Windows 7 64
Yeah man that's what i'm talking about. So it's not only the temps that make i worth to do. but it comes in pair with the voltage drop. Very nice indeed.

But i am not planning to do that on my new X2 4000 how tempting it is.:D
I'm still thinking of doing it with my 3700. But i can use the cash that i can get for it to.:rolleyes:. And not only the cash for the cpu but also for the mobo and ram.

But a second rig would be cool.:D
 
Top