• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

How to exchange caps

Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
A little photo guide about how I do it :)

You will need a classic transformer soldering iron, no less that 75W. I use this oldie one for 26 years:


Some resin is need too:


And a little bit of tin:


And tin suction tool:


...and of course replacement caps and something with bad caps. In this case I choose very simple recap of Jaton GF2MX400 card. Of course this card is phased out and you will probably not made and 3DMark world record with it, recapped or not, but for testing or normal office use it is perfect. Thanks to it's passive heatsink and small size it is preferred graphic card, where you need just one to be. I use these cards in folding and testing machines ;)

So, let's first take a look at the card itself:

As you can see, we gonna need:
1x 1000uF 6.3V d8 Samxon GC
4x 470uF 6.3V d6.3 Samxon GD
3x 10uF 25V d4 Samxon ZS

Let's take a look at the original caps...

...well, it is obvious they gotta go. Asiacon is the same as Evercon and this is the same cr*p as G-Luxon... :mad:

Step first - desolder with the soldering iron the caps:

Every time before use the soldering iron, dip it to the resin to protect against oxidation not only the contacts, but the actual soldering iron how wire tip. Result did not look ver pretty, but caps are gone now :D The white or shaded (or other way highlighted) holes are typically for the negative cap polarity wires. Of course you gotta stay alert for exceptions and crazy designs, witch can swap the polarity! Sometimes it is better first take a picture of the card to have proof on how it looked before... ;)

Now come the hardest step - suck off tin from at least one of the holes. Choose the one that is isolated from the rest of the PCB. This way you heat up most only small piece of tin and PCB and hence you should be able to suck the tin off easily.

Result - one hole is free.

Now take the replacement cap - take care about the polarization (on some cards, such as Gigabyte FX5200/FX5600XT, it is contrariwise!). Caps has one longer leg, that is the positive wire. If you have free the positive hole, you are good to go. Insert the longer positive wire inside and the negative adjust to be pressing exactly against the tin in the not free yet hole. Apply only light pressure. If you need more pressure, shorten the wires, but leave the positive wire longer.


From the bottom side heat up the tin in the negative hole and after a while (depends how big area of PCB you heating up) the cap nicely slide in place. Looks this way:

If you got free the negative hole instead, then cut the positive wire of the cap in middle, so it get shorter that the negative wire and then work it out same way.
Caps wires should be put thru to the end. Exception from this is only when you solder smaller or bigger spaced cap into holes that did not match. In that case - depends on how much the wires are getting dilate or closer - leave at least 3mm for the bend. Pressing too much in this case is very likely to damage almost any cap!

When you have the cap in place as it should be, then cut off the remaining wires. Leave just about 1mm from them. And then with plenty of resin again solder them.

Now it does not look pretty at all, right? :eek: Well, let's continue till we have every caps soldered first.

Now will come the technical spirit in action. Using brush add the spirit in place where the resin is:

And leave couple of seconds to take effect. You can see that the resin is breaking up and melting already. You can help big chunks get off by sharpened piece of hard wood - notably increasing the rate how the resin leave the PCB.

Then first with rubber, also wetted in spirit, rub off the remains of it. Last small remaining of the resin is best to get off by brush, wetted in spirit again. The brush has to have reasonably tough strings.

(image also show desoldered CE filters and coils replaced by pieces of wires)

With careful clean up you can get professional looking soldering joints.


And now you can only be delighted looking at how the new nice caps beautifully looking at the card.


Whole look on the card with now exchanged caps.


With such simple graphic card with minimum caps you can be done in like 10 minutes top. And with a little work you got the assurance it will not fail you for years and years. And now back with it to the computer ;)



PS. sometimes happens - especially with small caps, where one can heat up with big soldering wire tip both holes - that it is possible solder the cap w/o actually sucking off the tin. Sometimes this is also the only one possibility, when the tin did not want get off and you did not want to damage the PCB... In this case simply cut the legs to be same and much shorter (so you can apply more pressure), align them right to booth holes, hold and from the bottom start heating and push... ;)
 

imperialreign

New Member
Joined
Jul 19, 2007
Messages
7,043 (1.15/day)
Location
Sector ZZ₉ Plural Z Alpha
System Name УльтраФиолет
Processor Intel Kentsfield Q9650 @ 3.8GHz (4.2GHz highest achieved)
Motherboard ASUS P5E3 Deluxe/WiFi; X38 NSB, ICH9R SSB
Cooling Delta V3 block, XPSC res, 120x3 rad, ST 1/2" pump - 10 fans, SYSTRIN HDD cooler, Antec HDD cooler
Memory Dual channel 8GB OCZ Platinum DDR3 @ 1800MHz @ 7-7-7-20 1T
Video Card(s) Quadfire: (2) Sapphire HD5970
Storage (2) WD VelociRaptor 300GB SATA-300; WD 320GB SATA-300; WD 200GB UATA + WD 160GB UATA
Display(s) Samsung Syncmaster T240 24" (16:10)
Case Cooler Master Stacker 830
Audio Device(s) Creative X-Fi Titanium Fatal1ty Pro PCI-E x1
Power Supply Kingwin Mach1 1200W modular
Software Windows XP Home SP3; Vista Ultimate x64 SP2
Benchmark Scores 3m06: 20270 here: http://hwbot.org/user.do?userId=12313
awesome guide, man! very well written and excellent pics for examples! I've done similar work before, but never that pretty! :toast:
 
Joined
May 28, 2005
Messages
4,994 (0.73/day)
Location
South of England
System Name Box of Distraction
Processor Ryzen 7 1800X
Motherboard Crosshair VI Hero
Cooling Custom watercooling
Memory G.Skill TridentZ 2x8GB @ 3466MHz CL14 1T
Video Card(s) EVGA 1080Ti FE. WC'd & TDP limit increased to 360W.
Storage Samsung 960 Evo 500GB & WD Black 2TB storage drive.
Display(s) Asus ROG Swift PG278QR 27" 1440P 165hz Gsync
Case Phanteks Enthoo Pro M
Audio Device(s) Phillips Fidelio X2 headphones / basic Bose speakers
Power Supply EVGA Supernova 750W G3
Mouse Logitech G602
Keyboard Cherry MX Board 6.0 (mx red switches)
Software Win 10 & Linux Mint
Benchmark Scores https://hwbot.org/user/infrared
Very tidy soldering. I take my hat off to you :)
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
Very Nice.... thanks for the write up!
 

russianboy

New Member
Joined
Dec 9, 2005
Messages
1,799 (0.27/day)
Processor AMD 3500+ Venice at stock
Motherboard ECS K8T890-A
Memory 1 Gb Corsair Valueram CAS 3
Video Card(s) Connect3d X800 GTO OC'd to 551.25/551.25
Storage 4 mixed up drives
Display(s) Acer AL2216W 22"LCD
Case Generic noname crap
Audio Device(s) Realtec AC'97
Power Supply 500 watt Ultra PSU
Software Win2k Pro, XP, Ubuntu linux, and Vista
75 watts?

overkill, 25 watts is fine.
 
Joined
Feb 12, 2006
Messages
2,318 (0.35/day)
System Name MONEY PIT
Processor i7-3770K @ 4800 1.20v batch #3231B415 Delided
Motherboard ASrock Z77 OC Formula w onboard waterblocks
Cooling Apogee HD, MCP655,rad MCR320-XP,Micro Rev2 res
Memory G,skill Trident X F3-2400C10D-16GTX
Video Card(s) EVGA GTX 980 Ti Classified with EK nickel/acetal waterblock installed
Storage 2x120gig Wildfire raid0 2x120gig VERTEX3 raid0
Display(s) 3/ Samsung2343bwx + 65in LG 4K
Case NZXT Phantom White w/red
Audio Device(s) ReCon3d fatal1ty pro, Logitech z906 THX
Power Supply corsair AX860i
Mouse Rat7
Software 64bit ++++ win 10
great little read gets right to the point look forward to more
 
Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
imperialreign - thanks a lot :toast: The idea was from Bluetoth from OCW site, tough, that I should provide some guide at least how I do it. Maybe someone come with better tricks? :D
And soldering just took some practice and time. And lot's of resin and then the cleaning, lol ;) W/O it it never looks pretty at all ;)

infrared - thank you very much. It was just a quick work, even with the photos I was done in like 15 min or so, so... Not my best, just my best documented recap :p

d44ve - thank you - you are welcome. Hope someone learn a bit - or come with even better ideas ;)

russianboy - I was never be able to desolder mosfets or big caps (like imput caps in PSU) with my TWO 30W solders in reasonable time, so... My friend HoNY suggest using no less that 150W soldering iron, so go figure :D
He also suggested that when unclear, then the hole with square soldering point is always the positive hole :p

Frogger - thank you. Well, what more? :p I need to get some caps first to recap things :D ;) I run out of caps :nutkick:
 
Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
Trick with dental pick ;)

The hardest part on recapping is cleaning the holes for new caps. So, there come a little trick...



Yep, with this is the very same dental pick your dentist use to push on your teeths. You can buy it in medical supply shops, the only slight disadvantage is that the quality ones cost premium. But the vacuum tin sucking toy is not even recommended on BadCaps, because from heated PCB it easily can suck-off small traces, or by the back impact it tear them on the mobo. Sometimes it happen for me and certain low-quality mainboards (like JetWay V266B, Abit BX133 and so on) are very prone to this.

So, at first we have holes after desoldered cap (or never soldered cap there) full of tin:




So just attach the pick and reasonably push on it with one hand to stay in place (beware, it is very sharp, be carefull!):




From the other side heat up the PCB with iron and soon the pick do thru the hole like hot knife thru butter and try to push it as far, as you manage with reasonably small force:




Immidetelly after you reach the end, start wriggling with it to sides/up and down a bit, so it will not stuck to the tin or resin in the hole:




Now the big metal chunk of this dental pick come to play - it disperse the heat perfectly, so in just a few seconds we have a free hole:




Now let's repear that with the second hole, when we want to solder the cap inside easily (or he is on wrong place with bad access):




Push a little and we are on the second side easily again:




...and now we have both holes free and perfect for soldering new cap in:




As you can clearly see, this methos is easy, comfortable and fast. And the dental pick clean really well. Tin does not get attached on it at all and resin only very lightly. Cleaning with piece of old clothing and technical spirit is done in few seconds. The steel is very high quality, elastic a little and very hard to break. Almost impossible, I never managed it yet and I tried :) Comparing that to the nevereding cleaning of the vacuum tin suction tool... well, this is not comparable at all. Productivity in recapping go very much up using dental pick. Caps almost like jumping in the board ;) :D

Sometimes it happens that in the holes remain too much tin, that create knob around the holes, where capacitor will be soldered. Such knobs that are on the top of the PCB are easy to tear off by nail or cut off by scalpel.

Soldering was made by my 75W transformator solder, using lot's of resin. Pictures are not retouched at all and I did not even clean the board before taking the pictures. Board in question is Compaq Evo D310 one (MSI 6541 v1.0), exchange 10pcs of 1000uF 6.3V G-Luxon crap caps for 13pcs 1000uF 6.3V Samxon GC caps.
Board works well :)
 

spearman914

New Member
Joined
Apr 14, 2008
Messages
3,338 (0.57/day)
Location
Brooklyn, New York 11223
System Name Mine | Dad + Mom
Processor E8500 E0 Wolfdale @ 4.6GHz 1.5V | E2180 M0 Allendale @ 3.0GHz 1.3V
Motherboard Asus Maximus Formula (X48) w/ Rampage BIOS | Asus P5Q Pro (P45)
Cooling Xigmatek Rifle HDT-S1283 w/ SFF21F Fan | Arctic Cooling Freezer 7 Pro
Memory G.Skill Pi Black 2x2GB 1.02GHz CL5 | OCZ Reaper 2x2GB 1.05GHz CL5
Video Card(s) Sapphire 4870X2 2GB 820/1020MHz | Sapphire 4850 1GB 700/1100MHz
Storage WD VR 150GB 10K RPM + WD 500GB 7.2K RPM | WD 200GB 7.2K RPM
Display(s) Acer P243WAID 24" 1920x1200 LCD | Acer V193W 19" 1440x900 LCD
Case Cooler Master HAF 932 Full-Tower | Antec Twelve Hundred Mid-Tower
Audio Device(s) Fatal1ty Xtreme Gamer w/ Z-5500 5.1 | On-Board Audio w/ S-220 2.1
Power Supply PC Power and Cooling 750W Non-Modular | Corsair HX-520W Modular
Software Windows Vista Home Premium X64 | Windows Vista Home Premium X64
Benchmark Scores Not Wasting Time!
WOW... This is a great guide along with nice pics. But what happens if you do anything wrong?
 
Joined
Dec 5, 2006
Messages
7,704 (1.22/day)
System Name Back to Blue
Processor i9 14900k
Motherboard Asrock Z790 Nova
Cooling Corsair H150i Elite
Memory 64GB Corsair Dominator DDR5-6400 @ 6600
Video Card(s) EVGA RTX 3090 Ultra FTW3
Storage 4TB WD 850x NVME, 4TB WD Black, 10TB Seagate Barracuda Pro
Display(s) 1x Samsung Odyssey G7 Neo and 1x Dell u2518d
Case Lian Li o11 DXL w/custom vented front panel
Audio Device(s) Focusrite Saffire PRO 14 -> DBX DriveRack PA+ -> Mackie MR8 and MR10 / Senn PX38X -> SB AE-5 Plus
Power Supply Corsair RM1000i
Mouse Logitech G502x
Keyboard Corsair K95 Platinum
Software Windows 11 x64 Pro
Benchmark Scores 31k multicore Cinebench - CPU limited 125w
WOW... This is a great guide along with nice pics. But what happens if you do anything wrong?

Then you may or may not have a very serious problem :)

Nice writeup, done this myself a few times.
 
Joined
May 20, 2004
Messages
10,487 (1.45/day)
First I have to agree that 75W is overkill.

Second, I miss an essential part of the guide. Why would one want to replace caps? The example shows no bulging caps or anything and I see no argument for performance or whatever.
 

spearman914

New Member
Joined
Apr 14, 2008
Messages
3,338 (0.57/day)
Location
Brooklyn, New York 11223
System Name Mine | Dad + Mom
Processor E8500 E0 Wolfdale @ 4.6GHz 1.5V | E2180 M0 Allendale @ 3.0GHz 1.3V
Motherboard Asus Maximus Formula (X48) w/ Rampage BIOS | Asus P5Q Pro (P45)
Cooling Xigmatek Rifle HDT-S1283 w/ SFF21F Fan | Arctic Cooling Freezer 7 Pro
Memory G.Skill Pi Black 2x2GB 1.02GHz CL5 | OCZ Reaper 2x2GB 1.05GHz CL5
Video Card(s) Sapphire 4870X2 2GB 820/1020MHz | Sapphire 4850 1GB 700/1100MHz
Storage WD VR 150GB 10K RPM + WD 500GB 7.2K RPM | WD 200GB 7.2K RPM
Display(s) Acer P243WAID 24" 1920x1200 LCD | Acer V193W 19" 1440x900 LCD
Case Cooler Master HAF 932 Full-Tower | Antec Twelve Hundred Mid-Tower
Audio Device(s) Fatal1ty Xtreme Gamer w/ Z-5500 5.1 | On-Board Audio w/ S-220 2.1
Power Supply PC Power and Cooling 750W Non-Modular | Corsair HX-520W Modular
Software Windows Vista Home Premium X64 | Windows Vista Home Premium X64
Benchmark Scores Not Wasting Time!
First I have to agree that 75W is overkill.

Second, I miss an essential part of the guide. Why would one want to replace caps? The example shows no bulging caps or anything and I see no argument for performance or whatever.

That question "Why would one want to replace caps?". Um, incase its broken so you don't need to buy a new mobo.
 
Joined
Aug 30, 2006
Messages
7,195 (1.12/day)
System Name ICE-QUAD // ICE-CRUNCH
Processor Q6600 // 2x Xeon 5472
Memory 2GB DDR // 8GB FB-DIMM
Video Card(s) HD3850-AGP // FireGL 3400
Display(s) 2 x Samsung 204Ts = 3200x1200
Audio Device(s) Audigy 2
Software Windows Server 2003 R2 as a Workstation now migrated to W10 with regrets.
Dobry!

Very nice guide. Excellent photos! Seriously good photos. As good as any professional stock imagery. Very nice. What camera are you using? How are you lighting it? Are you on tripod?

a couple of people said:
First I have to agree that 75W is overkill.
I disagree. Speed soldering is the way to go, once you know how to do it. Having an underpowered iron, like 25W, means that it takes too long to heat up a small area. In the time it takes to hold the iron to heat the solder to melt... there is too much conduction of heat to the component, the PCB and other components. This can cause unwanted damage or heat blistering of the lacquer on the PCB.

I have an iron, which i recommend, that is 25W with a 140W burst button on the handle. That way you quick-heat the tip, then apply, then done.

There is nothing worse than holding an iron on a component for a long period trying to solder/desolder. Not only does it potentially cause damage to the component, if you are doing 10x or 100x of solders, it really slows progress.

Notice that the yellow iron that trodas is using has a trigger on it. So it is 75W controlled "burst". Such an iron is 10x better than a fixed 25W iron.
 
Last edited:
Joined
Dec 5, 2006
Messages
7,704 (1.22/day)
System Name Back to Blue
Processor i9 14900k
Motherboard Asrock Z790 Nova
Cooling Corsair H150i Elite
Memory 64GB Corsair Dominator DDR5-6400 @ 6600
Video Card(s) EVGA RTX 3090 Ultra FTW3
Storage 4TB WD 850x NVME, 4TB WD Black, 10TB Seagate Barracuda Pro
Display(s) 1x Samsung Odyssey G7 Neo and 1x Dell u2518d
Case Lian Li o11 DXL w/custom vented front panel
Audio Device(s) Focusrite Saffire PRO 14 -> DBX DriveRack PA+ -> Mackie MR8 and MR10 / Senn PX38X -> SB AE-5 Plus
Power Supply Corsair RM1000i
Mouse Logitech G502x
Keyboard Corsair K95 Platinum
Software Windows 11 x64 Pro
Benchmark Scores 31k multicore Cinebench - CPU limited 125w
Amazing how people never read what I write. Why do I keep bothering... Additionally it wasn't even about a mobo.

He is simply saying that he should add a few things to reasons why someone would want to replace capacitors.
 

imperialreign

New Member
Joined
Jul 19, 2007
Messages
7,043 (1.15/day)
Location
Sector ZZ₉ Plural Z Alpha
System Name УльтраФиолет
Processor Intel Kentsfield Q9650 @ 3.8GHz (4.2GHz highest achieved)
Motherboard ASUS P5E3 Deluxe/WiFi; X38 NSB, ICH9R SSB
Cooling Delta V3 block, XPSC res, 120x3 rad, ST 1/2" pump - 10 fans, SYSTRIN HDD cooler, Antec HDD cooler
Memory Dual channel 8GB OCZ Platinum DDR3 @ 1800MHz @ 7-7-7-20 1T
Video Card(s) Quadfire: (2) Sapphire HD5970
Storage (2) WD VelociRaptor 300GB SATA-300; WD 320GB SATA-300; WD 200GB UATA + WD 160GB UATA
Display(s) Samsung Syncmaster T240 24" (16:10)
Case Cooler Master Stacker 830
Audio Device(s) Creative X-Fi Titanium Fatal1ty Pro PCI-E x1
Power Supply Kingwin Mach1 1200W modular
Software Windows XP Home SP3; Vista Ultimate x64 SP2
Benchmark Scores 3m06: 20270 here: http://hwbot.org/user.do?userId=12313
I disagree. Speed soldering is the way to go, once you know how to do it. Having an underpowered iron, like 25W, means that it takes too long to heat up a small area. In the time it takes to hold the iron to heat the solder to melt... there is too much conduction of heat to the component, the PCB and other components. This can cause unwanted damage or heat blistering of the lacquer on the PCB.


I completely agree - I've only recently gotten back into soldering PCBs, and I've found even a 35/45W unit doesn't produce enough heat to liquify the solder before it starts cooking components.

Although, I've found when working with small surface-mount components, 15W-25W is usually just enough, but I've been shying away from such low outputs when dealing with through-PCB headers.



BTW, @trodas - excellent addition to the guide, man! I've got a set of picks in my toolbox at the shop, I don't know why I never thought to use them to clean solder out of PCB terminals! :slap: = myself
 
Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
spearman914 -
But what happens if you do anything wrong?

Thanks. Well, then depends much much wrong this is and if you discover it before powering the thing back on, or not. Usually there is not much problems. Caps are easy. Smaller SMD mounted componets with MANY legs, well, that IS the challenge.
Of course this little photoguide was never meant for people that cannot solder well.
If you solder something wrong, you just can clean it and solder it again and again... till you do it right. Practice on dead/worthless stuff first.



DanTheBanjoman -
First I have to agree that 75W is overkill.

I don't know who are you agree with, however it is clear to me you never exchanged caps on few mainboards/gfx cards or PSUs. I did, as you can see, just a few of my photo-documented recaps for witch I did not lost pictures (yet):
http://capsmod.net/forum/viewthread.php?tid=94&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=121&extra=page=2
http://capsmod.net/forum/viewthread.php?tid=130&extra=page=2
http://capsmod.net/forum/viewthread.php?tid=76&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=80&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=81&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=167&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=169&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=266&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=267&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=327&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=342&extra=page=1
http://capsmod.net/forum/viewthread.php?tid=346&extra=page=1
http://trodas.wz.cz/index.php?act=ST&f=16&t=337&s=

You are wellcome to try 35W iron on PSU recap, or even Vcore recap. I had problems with 75W there, so...

I miss an essential part of the guide. Why would one want to replace caps? The example shows no bulging caps or anything and I see no argument for performance or whatever.

Well, if you miss that, then you probably also miss this thread:
http://forums.techpowerup.com/showthread.php?t=39327
witch well explain why it is mandatory to replace known bad caps, as Asiacon is. People all around the world contributed to this bad caps list:
http://capsmod.net/forum/viewthread.php?tid=19&extra=page=1
...so you know what cap are you facing. Any many bad caps did not show any bulging or leaking, yet they still can and in the end will fry your HW.
There are also good performance reasons for recap to more quality caps, as I confirmed the findings of other that using quality Vcore caps end up in consistently faster SuperPI scores that on completely stable machine, but with worser a bit caps...!
http://capsmod.net/forum/viewthread.php?tid=130&extra=page=2


lemonadesoda - good points ;) Thanks.


imperialreign - you see, experience if worth everything. And well, when I cannot yet recap my X-Fi, then I can do a little guide that might help someone, or might not ;)
Some people will just reject it, so, whatever :D
Glad you learn something usefull, but practice on dead/worthless HW first ;)
 
Top