|
May 11, 2005, 05:43 PM
|
#1 |
 Join Date: May 2005
Location: Indonesia
Posts: 10 (0.00/day)
Thanks: 1
Thanked 0 Times in 0 Posts
|
ATI Tool 023 Misreading?
I have GeCube R9550 XT with 398.25/249.5 as default
 . When I used ATI Tool v.020 it read just correct also in radlinker, but problem occur when i installed atitool v.023. It read 300.9/176.5 as the default but not in radlinker and PC Wizard 2005 they both recognize the card clocks very well. Any info?One more question I have MSI RX9550 TD128 (only cooper heatsink with no fan) with samsung chips (5.0ns if i'm not wrong), can I flash the bios with 9600 pro? anyone ever tried it? 
|
|
|
|
May 11, 2005, 05:44 PM
|
#2 |
|
Join Date: May 2005
Location: Indonesia
Posts: 10 (0.00/day)
Thanks: 1
Thanked 0 Times in 0 Posts
|
sorry for the signature. i'm a newbie in here, dont know why it goes so big. my bad....
|
|
|
|
|
May 11, 2005, 05:59 PM
|
#3 |
|
Benevolent Dictator
Join Date: May 2004
Location: Stuttgart, Germany
Posts: 13,792 (4.18/day)
Thanks: 184
Thanked 10,289 Times in 3,175 Posts
   |
dump the bios to a file using atitool then email it to w1zzard@gmx.net
|
|
|
|
|
May 11, 2005, 06:12 PM
|
#4 | |
|
Join Date: May 2005
Location: Indonesia
Posts: 10 (0.00/day)
Thanks: 1
Thanked 0 Times in 0 Posts
|
Quote:
|
|
|
|
|
|
May 11, 2005, 06:24 PM
|
#5 |
|
Join Date: May 2005
Location: Indonesia
Posts: 10 (0.00/day)
Thanks: 1
Thanked 0 Times in 0 Posts
|
is it okay to flash the rx9550 bios with 9600 pro (there is no 9600 non pro for msi)?
what about the temp? am i have to change the heatsink? fyi, it arround 49-55'C when i'm OCed it similar to 9600NP (i figured it out by comparing the processor hsf and the vga sink by hand) theres no problem with the memory since i put a ramsink on the upper side. when i touched the ramsink it's a lil hot but not the ram on the other side (the ram putted doble sided with same positions), only the ramsinks lil hot. |
|
|
|
|
May 15, 2005, 07:15 PM
|
#6 |
|
Join Date: May 2005
Posts: 3 (0.00/day)
Thanks: 0
Thanked 0 Times in 0 Posts
|
i dunno if this has to do with this issue, i have a PowerColor R9550 256Mb/128Bits 250core/200mem with Samsung 5n Mems, using ATITool 0.23/0.22 :
ATITool v0.0.23 started. 2005-05-15 12:49:02 Detected GPU Chip: 0x0 (0), 4 Pipelines, 3840 MB 2005-05-15 12:49:02 Temperature monitoring: not supported 2005-05-15 12:49:02 Could not locate ATI BIOS - assuming 27.000 Mhz Ref. clock If try Find Max Core or Mem got a message saying somthing like "images doesn't match" and it hangs. ATITool v0.0.22 started. 2005-05-15 12:49:02 Detected GPU Chip: 0x0 (0), 8 Pipelines, 3840 MB 2005-05-15 12:49:02 Temperature monitoring: not supported 2005-05-15 12:49:02 Could not locate ATI BIOS - assuming 27.000 Mhz Ref. clock with this version it would run smooth the Find Max tests. What could be wrong i've tried Catalyst Originals, Omegadrivers and softmod (all 5.4) and got the same results, or i need to flash the bios before? Thanks in advance. |
|
|
|
|
May 15, 2005, 08:35 PM
|
#7 |
|
Benevolent Dictator
Join Date: May 2004
Location: Stuttgart, Germany
Posts: 13,792 (4.18/day)
Thanks: 184
Thanked 10,289 Times in 3,175 Posts
|
ozz: settings -> overclocking -> video card drop down .. select the 9550 in there ..
|
|
|
|
|
May 15, 2005, 10:18 PM
|
#8 |
|
Join Date: May 2005
Posts: 3 (0.00/day)
Thanks: 0
Thanked 0 Times in 0 Posts
|
 shame on me .... sry... thanks a lot W1zz.  If is not much asking for another advice... would you recomend to flash it for getting the 9600 mod? i've been looking for a BIOS that somehow matches the actual memory (256Mb Samsung 5n) but only 128Mb BIOS ara available, if i flash it with one of those it would keep the 256Mb?  Thanks a lot again Last edited by ozzzyyz; May 15, 2005 at 10:31 PM. |
|
|
|
|
May 16, 2005, 07:46 AM
|
#9 |
|
Benevolent Dictator
Join Date: May 2004
Location: Stuttgart, Germany
Posts: 13,792 (4.18/day)
Thanks: 184
Thanked 10,289 Times in 3,175 Posts
|
a 128mb bios on a 256mb card will either not work or give you 128mb
|
|
|
|
|
May 17, 2005, 01:09 PM
|
#10 |
|
Join Date: May 2005
Location: Indonesia
Posts: 10 (0.00/day)
Thanks: 1
Thanked 0 Times in 0 Posts
|
Today i install it again and it already works...
Thx |
|
|
|
|
May 21, 2005, 01:46 PM
|
#11 | |
|
Join Date: May 2005
Posts: 2 (0.00/day)
Thanks: 0
Thanked 0 Times in 0 Posts
|
Quote:
2003-01-01 03:17:05 ATITool v0.0.23 started. 2003-01-01 03:17:05 Detected GPU Chip: RV350 (4153), 4 Pipelines, 256 MB 2003-01-01 03:17:05 Temperature monitoring: not supported 2003-01-01 03:17:11 Profile 'Rajendra' loaded. Clocks set to: 415.38 / 224.31 No problems there at all. |
|
|
|
|
|
May 21, 2005, 03:32 PM
|
#12 |
|
Join Date: May 2005
Posts: 3 (0.00/day)
Thanks: 0
Thanked 0 Times in 0 Posts
|
Hey, I'm currently using the 0.24 beta 10, and it seems this bug isn't in the new beta verson, but whenever I used 0.23 it dedects my x850xt as if it only has 8 pipelines, everything else (and the 0.24 beta 10) reads it as 16 pipelines so I know its not my card thats broken, just thought I'd like to mention it if anyone else has a x850xt and reads that atitool only detects 8 pipelines not to worry, all your pipelines are there.
//KozZyRules |
|
|
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Random Restars - > Video Card - > PSU | TrAiN^WrEcK | General Hardware | 37 | May 8, 2007 02:05 PM |
| ATI Tool with ATI 3200Xpress chipset, socket AM2 | Agent_D | ATITool | 1 | Sep 14, 2006 12:25 PM |
| ATi Tool on nVidia graphics cards. | Israar | ATITool | 5 | Dec 2, 2005 11:52 PM |
| question about ati tool and ati tray tools | naokiakira | Overclocking & Cooling | 4 | Nov 8, 2005 12:32 AM |
| ATI CCC runtime and ATI Tool error:"init of find max: subsequent images are different | AndreyPopov | ATITool | 0 | Feb 13, 2005 04:17 PM |
System Specs
