Where can I find Northbridge Temps?

spixel · Aug 9, 2007, 10:12 PM

Where can i find my northbridge temp

and is MCH voltage what makes it hotter , whats normal temps for it

spixel · Aug 9, 2007, 10:38 PM

bump , need to know fast

driver66 · Aug 9, 2007, 10:41 PM

Quote:

Originally Posted by spixel

Where can i find my northbridge temp

and is MCH voltage what makes it hotter , whats normal temps for it

If ur mobo supports it uguru should tell you. That is if it has a temp sensor

If it does then it will also show in your bios.
yes MCH is your northbrige voltage.

spixel · Aug 9, 2007, 11:20 PM

nguru doesnt give nb temps , pmw and cpu only :S , when i enable nb in abit eq it comes up with a warning saying the fan is running at 0rpm

Mediocre · Aug 9, 2007, 11:27 PM

just touch the heatsink I have circled in green below. If you can't leave your finger on it for more than a few seconds...its too hot.

You would need a temp monitor setup and a thermo-couple to read the temp, and even then your only reading the heatsinks temp.

My old nforce 580 board ran so hot, you couldn't keep your finger on it for much more than a few seconds before it started to burn.

giorgos th. · Aug 9, 2007, 11:35 PM

from measurements,if you can`t leave your finger more than 5-10" the temp is over 45-50C..

driver66 · Aug 10, 2007, 12:02 AM

Quote:

Originally Posted by spixel

nguru doesnt give nb temps , pmw and cpu only :S , when i enable nb in abit eq it comes up with a warning saying the fan is running at 0rpm

that means ur mobo doesnt have a sensor and there is no ACCURATE way to measure it besides a infared temp gun

sneekypeet · Aug 10, 2007, 12:18 AM

Have you tried to download Everest or the like to see what they say?

Thermopylae_480 · Aug 10, 2007, 12:18 AM

Please remember to use thread titles which accurately describe the problem being discussed in the thread. Vague and in-descriptive titles are subject to change as stated in the Forum Guidelines. Threads with descriptive titles often receive more attention than those with vague, in-descriptive, or in-suitable titles.

-Thanks

spixel · Aug 10, 2007, 12:32 AM

everest reads 27 on motherboard temp , doesnt move on load tho so im guessing thats not northbridge , what other programmes could i use.

also whats AUX3 fan , i have a titan amanda cooler which rpm is got from a pci card , but there was also a connector which was plugged into the mobo. CPU fan reads 1680rpm and aux3 reads 1620 and sometimes 1560 , when thats 1560 my CPU fan speed goes to 1620 :S anyway to keep my cpu rpm full speed all the time.

driver66 · Aug 10, 2007, 01:39 AM

If there is NO TEMP SENSOR no sowftware on this earth will read ur temps

It will take hardware temp sensors

imperialreign · Aug 10, 2007, 01:52 AM

You can use an infrared temp gun to grab a quick, at-the-moment reading - it won't be 100% accurate, but within a few degrees

driver66 · Aug 10, 2007, 02:00 AM

Quote:

Originally Posted by driver66

that means ur mobo doesnt have a sensor and there is no ACCURATE way to measure it besides a infared temp gun

LOL

post #7

spixel · Aug 10, 2007, 02:02 AM

maybe i just have uguru configured wrong

board is abit aw9d max , if anyone knows how to get it to show nb temps / fan speeds then :}

i wont be able to get the hardware to test it so what is usually considered a "safe" mch voltage , right now mines at 1.54 . could i increase it a bit.

driver66 · Aug 10, 2007, 02:07 AM

Quote:

Originally Posted by spixel

maybe i just have uguru configured wrong

board is abit aw9d max , if anyone knows how to get it to show nb temps / fan speeds then :}

i wont be able to get the hardware to test it so what is usually considered a "safe" mch voltage , right now mines at 1.54 . could i increase it a bit.

Your gonna have to guess ,it has no temp sensor!

mine has been at 1.55 for month's Abit ab9pro

Aug 9, 2007, 10:12 PM	#1
spixel Join Date: Jul 2007 Posts: 294 (0.14/day) Thanks: 27 Thanked 11 Times in 11 Posts System Specs	Where can I find Northbridge Temps? Where can i find my northbridge temp and is MCH voltage what makes it hotter , whats normal temps for it

Processor:	Intel i5 2500k @ 4.2ghz
Motherboard:	Asrock z77 Extreme4
Memory:	8GB Corsair LP 1600mhz
Video Card:	Gigabyte gtx570 + Evga gtx570 HD
Hard Disk:	Corsair Force GT 120gb
Optical Drive:	Samsung Lightscribe dvd-rw
CRT/LCD Model:	Samsung 931bw
Case:	Cooler Master Cosmos S
Sound Card:	Onboard
PSU:	Corsair vx550
Software:	Windows 7 Ultimate 64

Processor:	Intel i5 2500k @ 4.2ghz
Motherboard:	Asrock z77 Extreme4
Memory:	8GB Corsair LP 1600mhz
Video Card:	Gigabyte gtx570 + Evga gtx570 HD
Hard Disk:	Corsair Force GT 120gb
Optical Drive:	Samsung Lightscribe dvd-rw
CRT/LCD Model:	Samsung 931bw
Case:	Cooler Master Cosmos S
Sound Card:	Onboard
PSU:	Corsair vx550
Software:	Windows 7 Ultimate 64

Processor:	c2d e8400@ 3.8ghz 24/7
Motherboard:	Abit IP-35e 80$ lol
Cooling:	zalman cnps9700 led
Memory:	2 x 2 gig patriot viper
Video Card:	evga Gtx 285 oc
Hard Disk:	2 x 300gig sata seagate 7200.10 in raid 0/ 1.5TB for backup
Optical Drive:	samsung writemaster sata dual layer 16x dvd lightscribe
CRT/LCD Model:	acer 24" TFT LCD AL2416WBSD
Case:	Antec 902
Sound Card:	XtremeGamer Fatal1ty Pro series
PSU:	ocz gamextreme 700w
Software:	windows 7 ultimate

Processor:	Intel i5 2500k @ 4.2ghz
Motherboard:	Asrock z77 Extreme4
Memory:	8GB Corsair LP 1600mhz
Video Card:	Gigabyte gtx570 + Evga gtx570 HD
Hard Disk:	Corsair Force GT 120gb
Optical Drive:	Samsung Lightscribe dvd-rw
CRT/LCD Model:	Samsung 931bw
Case:	Cooler Master Cosmos S
Sound Card:	Onboard
PSU:	Corsair vx550
Software:	Windows 7 Ultimate 64

Aug 9, 2007, 10:38 PM	#2
spixel Join Date: Jul 2007 Posts: 294 (0.14/day) Thanks: 27 Thanked 11 Times in 11 Posts System Specs	bump , need to know fast

Aug 9, 2007, 11:20 PM	#4
spixel Join Date: Jul 2007 Posts: 294 (0.14/day) Thanks: 27 Thanked 11 Times in 11 Posts System Specs	nguru doesnt give nb temps , pmw and cpu only :S , when i enable nb in abit eq it comes up with a warning saying the fan is running at 0rpm

Aug 9, 2007, 11:27 PM	#5
Mediocre Join Date: Jun 2006 Posts: 1,023 (0.40/day) Thanks: 111 Thanked 81 Times in 74 Posts System Specs	just touch the heatsink I have circled in green below. If you can't leave your finger on it for more than a few seconds...its too hot. You would need a temp monitor setup and a thermo-couple to read the temp, and even then your only reading the heatsinks temp. My old nforce 580 board ran so hot, you couldn't keep your finger on it for much more than a few seconds before it started to burn.

Processor:	C2D E8400 @ 3.60GHz
Motherboard:	ASUS P5Q-Pro w/ extra Vreg HS
Cooling:	Apogee GTX, 2x120mm DD, MCP-1000P Res/Pump, all 3/8" 7x80mm (4x push/pull, 2x exhaust, 1x side)
Memory:	2 x 1GB Corsair Dominator DDR2 1066 @ 800 (4-3-3-6)
Video Card:	EVGA 9800GTX+
Hard Disk:	3 x 80 GB WD SATA300 (2x RAID 0)
CRT/LCD Model:	Scepter x37 1080p 37" LCD & Samsung 204B
Case:	CoolerMaster HAF932
Sound Card:	Onboard
PSU:	Mushkin HP-580AP (C/O TPU!)
Software:	Vista Ultimate (32-bit)

Aug 9, 2007, 11:35 PM	#6
giorgos th. Join Date: Nov 2005 Location: Athens - Hellas Posts: 1,457 (0.53/day) Thanks: 22 Thanked 117 Times in 73 Posts System Specs	from measurements,if you can`t leave your finger more than 5-10" the temp is over 45-50C.. __________________

Processor:	C2D E7600
Motherboard:	GA EG41M ES2L
Memory:	2GB ADATA 800MHZ
Video Card:	ASUS HD4350
Hard Disk:	OCZ VERTEX TURBO 32GB + 2 MORE..
Optical Drive:	LG
CRT/LCD Model:	SM226BW
Sound Card:	7.1 HD / X-540
Software:	7X86 ULT

Aug 10, 2007, 12:18 AM	#8
sneekypeet Unpaid Babysitter Join Date: Apr 2006 Posts: 18,983 (7.32/day) Thanks: 3,032 Thanked 5,481 Times in 3,947 Posts System Specs	Have you tried to download Everest or the like to see what they say?

System Name:	His
Processor:	Intel i7 3770K Cooled with Swiftech Apogee Drive II
Motherboard:	Asus Maximus V Extreme
Cooling:	Swiftech MCR-320 Cooled With Corsair SP120 Fans
Memory:	4X4GB Corsair Dominator Platinum 2666 C11
Video Card:	Asus GTX680 Direct Cu II TOP
Hard Disk:	Corsair Force GT 180GB / Samsung Spinpoint F1 1TB
Optical Drive:	- - - - - - -
CRT/LCD Model:	Samsung 40" 120hz LCD
Case:	SilverStone Temjin TJ11
Sound Card:	Realtek on board > Sony receiver > Cerwin Vega's
PSU:	Corsair AX1200
Software:	Windows 7 Ultimate 64

Aug 10, 2007, 12:18 AM	#9
Thermopylae_480 Join Date: May 2005 Location: Little Rock Arkansas, United States Posts: 2,656 (0.91/day) Thanks: 40 Thanked 417 Times in 287 Posts System Specs	Please remember to use thread titles which accurately describe the problem being discussed in the thread. Vague and in-descriptive titles are subject to change as stated in the Forum Guidelines. Threads with descriptive titles often receive more attention than those with vague, in-descriptive, or in-suitable titles. -Thanks __________________ All, too, will bear in mind this sacred principle, that though the will of the majority is in all cases to prevail, that will to be rightful must be reasonable; that the minority possess their equal rights, which equal law must protect, and to violate would be oppression.

System Name:	Monolith
Processor:	Intel Xeon E3110 Wolfdale@3.5GHz
Motherboard:	MSI P35-Neo
Cooling:	Active Air
Memory:	4GB DDR2 800
Video Card:	Sapphire HD 3850 512MB PCI-E
Hard Disk:	1 x 80GB Internal, 1 x 250GB Internal, 1 x 40GB External
Optical Drive:	Asus CD/DVD Burner, 1.44MB Floppy Drive!!!!!!!
CRT/LCD Model:	Acer X203w
Case:	Generic black case with locking front bezel
Sound Card:	Creative SB Audigy 2 ZS
PSU:	500 Watt Seasonic M12
Software:	Windows 7 Ultimate x64

Aug 10, 2007, 12:32 AM	#10
spixel Join Date: Jul 2007 Posts: 294 (0.14/day) Thanks: 27 Thanked 11 Times in 11 Posts System Specs	everest reads 27 on motherboard temp , doesnt move on load tho so im guessing thats not northbridge , what other programmes could i use. also whats AUX3 fan , i have a titan amanda cooler which rpm is got from a pci card , but there was also a connector which was plugged into the mobo. CPU fan reads 1680rpm and aux3 reads 1620 and sometimes 1560 , when thats 1560 my CPU fan speed goes to 1620 :S anyway to keep my cpu rpm full speed all the time.

Aug 10, 2007, 01:39 AM	#11
driver66 Join Date: Jun 2007 Location: indiana Posts: 789 (0.36/day) Thanks: 439 Thanked 113 Times in 109 Posts System Specs	If there is NO TEMP SENSOR no sowftware on this earth will read ur temps It will take hardware temp sensors __________________ “cheap hooker can be sold cheaper, being a low-end product, you could probably give her a smaller cut? effectively increasing your revenue percentage. now all you need is to increase your absolute number of sales to make more money.” -W1zzard “you had a pedobear called mohammed as avatar .. should i go ahead and post your ip at al-qaeda forums?” -W1zzard

Aug 10, 2007, 01:52 AM	#12
imperialreign Join Date: Jul 2007 Location: Sector ZZ₉ Plural Z Alpha Posts: 4,001 (1.88/day) Thanks: 272 Thanked 953 Times in 710 Posts System Specs	You can use an infrared temp gun to grab a quick, at-the-moment reading - it won't be 100% accurate, but within a few degrees

System Name:	УльтраФиолет
Processor:	Intel Kentsfield Q9650 @ 3.8GHz (4.2GHz highest achieved)
Motherboard:	ASUS P5E3 Deluxe/WiFi; X38 NSB, ICH9R SSB
Cooling:	Delta V3 block, XPSC res, 120x3 rad, ST 1/2" pump - 10 fans, SYSTRIN HDD cooler, Antec HDD cooler
Memory:	Dual channel 8GB OCZ Platinum DDR3 @ 1800MHz @ 7-7-7-20 1T
Video Card:	Quadfire: (2) Sapphire HD5970
Hard Disk:	(2) WD VelociRaptor 300GB SATA-300; WD 320GB SATA-300; WD 200GB UATA + WD 160GB UATA
Optical Drive:	(2) I/O Magic "LightScribe" SATA DVD ± R/RW
CRT/LCD Model:	Samsung Syncmaster T240 24" (16:10)
Case:	Cooler Master Stacker 830
Sound Card:	Creative X-Fi Titanium Fatal1ty Pro PCI-E x1
PSU:	Kingwin Mach1 1200W modular
Software:	Windows XP Home SP3; Vista Ultimate x64 SP2
Benchmarks:	3m06: 20270 here: http://hwbot.org/user.do?userId=12313

Aug 10, 2007, 02:02 AM	#14
spixel Join Date: Jul 2007 Posts: 294 (0.14/day) Thanks: 27 Thanked 11 Times in 11 Posts System Specs	maybe i just have uguru configured wrong board is abit aw9d max , if anyone knows how to get it to show nb temps / fan speeds then :} i wont be able to get the hardware to test it so what is usually considered a "safe" mch voltage , right now mines at 1.54 . could i increase it a bit.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)