|
Apr 6, 2008, 08:54 PM
|
#1 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
Asus Maximus Formula / Rampage bios Bios settings thread
This thread is for bios setting only post your bios setting and chip type etc... so this can be a resource for people looking to overclock this complexed motherboard. This is not for discussion only information on what works with what chip. Keep this thread clean for quick reference not for discussion. To discuss the board use this thread. http://forums.techpowerup.com/showthread.php?t=54058
Here is another Asus maximus thread full of great info lets not clutter this thread like the one listed here. It is a great read but cluttered to death. http://www.xtremesystems.org/forums/...d.php?t=168119 I would love to take credit for these setting some were added to by me but are by no means mine. They are from several sources. Other people worked hard to get these setting. I just found them to work and posted them If you find one post it. Bios and utilities update page for the Rampage Formula http://support.asus.com/download/dow...Language=en-us Last edited by trt740; Sep 1, 2008 at 03:20 PM. |
|
|
| The Following 6 Users Say Thank You to trt740 For This Useful Post: |
|
Apr 6, 2008, 08:58 PM
|
#2 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
These setting will work for 500+ fsb with at e8400 /E3110
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 8 FSB Frequency : 500 FSB Strap to North Bridge : 333 PCI-E Frequency: 110 DRAM Frequency: DDR2-1200 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 18 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 45 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : 8 Write to Read Delay (S) : 3 Write to Read Delay (D) : 5 Read to Read Delay (S) : 4 Read to Read Delay (D) : 6 Write to Write Delay (S) : 4 Write to Write Delay (D) : 6 DRAM Static Read Control: Disabled Ai Clock Twister : moderate changed this to light Transaction Booster : Disabled Relax level: 0 CPU Voltage : 1.38v CPU PLL Voltage : AUTO North Bridge Voltage : 1.53 upped this to 1.57v DRAM Voltage : 2.12 FSB Termination Voltage : 1.40 South Bridge Voltage : 1.050 Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO DDR2 Controller REF Voltage : DDR2-REFF SB 1.5V Voltage : 1.5 |
|
|
|
|
Apr 6, 2008, 09:03 PM
|
#3 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
settings for Q6600 and this motherboard 450FSB
450FSB Quad-Core BIOS Settings
CPU Feature Ai Overclock Tuner [Manual] OC From CPU Level Up [Auto] CPU Ratio Control [Manual] Ratio CMOS Setting: [8] FSB Frequency [450] FSB Strap to North Bridge [400MHz] or [Auto] PCIE Frequency [110] DRAM Settings DRAM Frequency [DDR2-1199MHZ] or [800MHz] or [Auto] DRAM Command Rate [2T] DRAM Timing Control [Manual] CAS# Latency [5] RAS# to CAS Delay [5] RAS# Precharge [5] RAS# Active Time [12] RAS# To Ras# Delay [3] Row Refresh Cycle Time [42] Write Recovery Time [6] Read To Precharge Time [3] Read To Write Delay(S/D) [8] Write To Read Delay(S) [3] Write To Read Delay(D) [5] Read To Read Delay(S) [4] Read To Read Delay(D) [6] Write To Write Delay(S) [4] Write To Write Delay(D) [6] DRAM Static Read Control [Disabled] Ai Clock Twister [Strong] Transaction Booster [Enabled] Boost Level [0] Voltage Settings CPU Voltage [Whatever your CPU needs for 3.6GHz] CPU PLL Voltage [Auto] North Bridge Voltage [1.61v] DRAM Voltage [2.16v] FSB Termination Voltage [1.54v] South Bridge Voltage [Auto] Loadline Calibration [Enabled] CPU GTL Reference [0.63x] North Bridge GTL Reference [0.67x] DDR2 Channel A REF Voltage [Auto] DDR2 Channel B REF Voltage [Auto] DDR2 Controller REF Voltage [DDR2_REF] SB 1.5V Voltage [Auto] |
|
|
|
|
Apr 6, 2008, 09:06 PM
|
#4 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
good setting for 4.0ghz using a e8400 using 9x445fsb
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : AUTO - Ratio CMOS Setting : 9 FSB Frequency : 445 FSB Strap to North Bridge : 333 PCI-E Frequency: 100 DRAM Frequency: DDR2- 890 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 15 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 50 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : Auto Write to Read Delay (S) : Auto Write to Read Delay (D) : Auto Read to Read Delay (S) : Auto Read to Read Delay (D) : Auto Write to Write Delay (S) : Auto Write to Write Delay (D) : Auto DRAM Static Read Control: Disabled ( enabled will give better bandwidth but might create instability in ram) Ai Clock Twister : Strong Transaction Booster : Disabled Relax level: 0 CPU Voltage : 1.35 ( you may need to adjust this) CPU PLL Voltage : AUTO North Bridge Voltage : 1.49 DRAM Voltage : 2.00 FSB Termination Voltage : 1.40 South Bridge Voltage : 1.050 Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO DDR2 Controller REF Voltage : DDR2-REFF SB 1.5V Voltage : 1.5 __________________ |
|
|
|
|
Apr 7, 2008, 01:02 AM
|
#5 |
 
Join Date: Feb 2006
Location: ONTARIO CANADA
Posts: 1,930 (0.73/day)
Thanks: 324
Thanked 241 Times in 215 Posts
|
450x8 on Q6600/GO
Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 8 FSB Frequency : 450 FSB Strap to North Bridge : 400MHZ PCI-E Frequency: 110 DRAM Frequency: DDR2-1199 DRAM Command Rate : 2t DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 15 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time : AUTO Write Recovery Time : AUTO Read to Precharge Time : AUTO Read to Write Delay (S/D) : AUTO Write to Read Delay (S) : AUTO Write to Read Delay (D) : AUTO Read to Read Delay (S) : AUTO Read to Read Delay (D) : AUTO Write to Write Delay (S) : AUTO Write to Write Delay (D) : AUTO DRAM Static Read Control: Disabled Ai Clock Twister : Strong Transaction Booster : enabled [0] CPU Voltage : 1.45 CPU PLL Voltage : 1.65 North Bridge Voltage : 1.55 DRAM Voltage : 2.16 FSB Termination Voltage : 1.50 South Bridge Voltage : 1.10 Loadline Calibration : Enabled CPU GTL Reference : Auto North Bridge GTL Reference : Auto DDR2 Channel A REF Voltage : DDR2_REF DDR2 Channel B REF Voltage : DDR2_REF DDR2 Controller REF Voltage : DDR2_REF SB 1.5V Voltage : 1.5
__________________
You can't be a real country unless you have a beer and an airline-it helps if you have some kind of a football team,or some nuclear weapons,BUT at the very least you need a BEER!-Frank Zappa 
|
|
|
|
| The Following User Says Thank You to Frogger For This Useful Post: |
|
Apr 7, 2008, 05:15 PM
|
#6 | |
|
Eligible for custom title
Join Date: Apr 2005
Posts: 6,244 (2.12/day)
Thanks: 382
Thanked 1,526 Times in 865 Posts
|
Quote:
|
|
|
|
|
| The Following User Says Thank You to EastCoasthandle For This Useful Post: |
|
Apr 14, 2008, 12:54 AM
|
#7 |
Join Date: Sep 2006
Location: Great Yarmouth, United Kingdom.{East Anglian Coast}
Posts: 1,722 (0.70/day)
Thanks: 340
Thanked 249 Times in 222 Posts
|
450x8 on Q6600/GO
Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 8 FSB Frequency : 450 FSB Strap to North Bridge : Auto PCI-E Frequency: 107mhz DRAM Frequency: DDR2-901mhz DRAM Command Rate : 2t DRAM Timing Control: Manual CAS# Latency : 6 RAS# to CAS# Delay : 6 RAS# Precharge : 6 RAS# ActivateTime : 18 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time : AUTO Write Recovery Time : AUTO Read to Precharge Time : AUTO Read to Write Delay (S/D) : AUTO Write to Read Delay (S) : AUTO Write to Read Delay (D) : AUTO Read to Read Delay (S) : AUTO Read to Read Delay (D) : AUTO Write to Write Delay (S) : AUTO Write to Write Delay (D) : AUTO DRAM Static Read Control: Disabled Ai Clock Twister : moderate Transaction Booster : enabled [9] CPU Voltage : 1.4v CPU PLL Voltage : auto North Bridge Voltage : 1.49v DRAM Voltage : 2.18v FSB Termination Voltage : 1.40v South Bridge Voltage : 1.10 Loadline Calibration : Enabled CPU GTL Reference : x63 North Bridge GTL Reference : x67 DDR2 Channel A REF Voltage : auto DDR2 Channel B REF Voltage : auto DDR2 Controller REF Voltage : auto SB 1.5V Voltage : 1.55v
__________________
 MY RIG http://www.techpowerup.com/gallery/1346.html Heatware http://www.heatware.com/eval.php?id=66464 I hate people that take drugs... Customs Officers for example!! |
|
|
|
| The Following User Says Thank You to Nitro-Max For This Useful Post: |
|
Apr 21, 2008, 01:12 AM
|
#8 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
this let me run a E3110 at 8.5x500FSB or 4.25ghz stable.
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 8 FSB Frequency : 500 FSB Strap to North Bridge : 333 PCI-E Frequency: 110 DRAM Frequency: DDR2-1200 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 18 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 45 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : 8 Write to Read Delay (S) : 3 Write to Read Delay (D) : 5 Read to Read Delay (S) : 4 Read to Read Delay (D) : 6 Write to Write Delay (S) : 4 Write to Write Delay (D) : 6 DRAM Static Read Control: Disabled Ai Clock Twister : moderate changed this to light Transaction Booster : Disabled Relax level: 0 CPU Voltage : 1.38v CPU PLL Voltage : 1.60 North Bridge Voltage : 1.53 upped this to 1.57v DRAM Voltage : 2.12 FSB Termination Voltage : 1.55v South Bridge Voltage : 1.050 Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO DDR2 Controller REF Voltage : DDR2-REFF SB 1.5V Voltage : 1.5 this works in bios 0219 and 0308 rampage plus 1004 Maximus formula. Last edited by trt740; Apr 21, 2008 at 01:18 AM. |
|
|
|
|
Apr 25, 2008, 03:48 PM
|
#9 |
 
|
e8400 4.36Ghz w/NATIVE Rampage Bios 0308 Patriot Viper Fins 9600
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 9 FSB Frequency : 485 FSB Strap to North Bridge : 333 PCI-E Frequency: 110 (might help GX2 Oc'ing) DRAM Frequency: DDR2-1164 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 15 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 45 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : 8 Write to Read Delay (S) : 3 Write to Read Delay (D) : 5 Read to Read Delay (S) : 4 Read to Read Delay (D) : 6 Write to Write Delay (S) : 4 Write to Write Delay (D) : 6 DRAM Static Read Control: Disabled Ai Clock Twister : light Transaction Booster : Manual (Then Disable everything) Performance Level: 08 3rd Information WRITE to PRE Delay : AUTO READ to PRE Delay : AUTO PRE to PRE Delay : AUTO ALL PRE to ACT Delay : AUTO ALL PRE to REF Delay : AUTO CPU Voltage : (depends on your CPU they are all different, I would start with 1.4v) CPU PLL Voltage : 1.60 North Bridge Voltage : 1.59 DRAM Voltage : (Depends on rated spec) mine is 2.3v FSB Termination Voltage : 1.55v South Bridge Voltage : 1.10 Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO DDR2 Controller REF Voltage : DDR2-REFF SB 1.5V Voltage : 1.6 Last edited by slugzkea; Apr 29, 2008 at 03:46 PM. Reason: Forgot 3rd information. |
|
|
|
| The Following User Says Thank You to slugzkea For This Useful Post: |
|
May 8, 2008, 11:45 AM
|
#10 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
Bios setting for 500+ fsb woth ballistix tracer DDR 2 1066
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 8 FSB Frequency : 500 FSB Strap to North Bridge : 333 PCI-E Frequency: 110 DRAM Frequency: DDR2-1057 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 18 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 45 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : 8 Write to Read Delay (S) : 3 Write to Read Delay (D) : 5 Read to Read Delay (S) : 4 Read to Read Delay (D) : 6 Write to Write Delay (S) : 4 Write to Write Delay (D) : 6 DRAM Static Read Control: auto ( these three have to be on auto not sure why but thats the way it is) Ai Clock Twister : auto Transaction Booster : auto CPU Voltage : 1.38v CPU PLL Voltage : AUTO North Bridge Voltage : 1.53 upped this to 1.57v DRAM Voltage : 2.12 FSB Termination Voltage : 1.40 South Bridge Voltage : 1.050 Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO DDR2 Controller REF Voltage : DDR2-REFF SB 1.5V Voltage : 1.5 |
|
|
|
|
May 8, 2008, 10:24 PM
|
#11 |
|
Eleet Hardware Junkie
Join Date: Oct 2007
Location: Republic of Texas
Posts: 14,993 (7.31/day)
Thanks: 4,318
Thanked 3,285 Times in 2,186 Posts
 |
settings for E8500 @ 5.016ghz with 528mhz FSB with RF0308 bios
Extreme Tweaker
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Setting : 9.5 FSB Strap to North Bridge : 400 FSB Frequency : 528 PCI-E Frequency: 115 DRAM Frequency: DDR2-1056mhz DRAM Command Rate : 2N DRAM CLK Skew on Channel A: Delay 350ps DRAM CLK Skew on Channel B: Delay 200ps DRAM Timing Control: Manual CAS# Latency : 4 RAS# to CAS# Delay : 4 RAS# Precharge : 4 RAS# ActivateTime : 12 RAS# to RAS# Delay : 3 Row Refresh Cycle Time : 45 Write Recovery Time : 6 Read to Precharge Time : 3 Read to Write Delay (S/D) : 8 Write to Read Delay (S) : 3 Write to Read Delay (D) : 5 Read to Read Delay (S) : 4 Read to Read Delay (D) : 6 Write to Write Delay (S) : 4 Write to Write Delay (D) : 6 3rd Information WRITE to PRE Delay : AUTO READ to PRE Delay : AUTO PRE to PRE Delay : AUTO ALL PRE to ACT Delay : AUTO ALL PRE to REF Delay : AUTO DRAM Static Read Control: Disabled Ai Clock Twister : Moderate Transaction Booster : Auto CPU Voltage : 1.525v CPU PLL Voltage : 1.58v North Bridge Voltage : 1.71v DRAM Voltage : 2.3v FSB Termination Voltage : 1.50v South Bridge Voltage : 1.05 SB 1.5V Voltage : 1.50v Loadline Calibration : Enabled CPU GTL Reference : 0.63X North Bridge GTL Reference : 0.67X DDR2 Controller REF Voltage : DDR2-REF DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO NOTE: IF your lucky enough to have a chip that can do this well. these settings WILL help you. it took a while to figure these out. here is the system setup... Maximus formula with rampage 0308 bios E8500 2x1gig's crucial ballistix tracer 1066mhz 3870x2 enermax infinity 720watt PSU |
|
|
|
|
Jun 10, 2008, 02:48 AM
|
#12 |
|
Battosai
Join Date: Oct 2007
Location: In a library somewhere on this earth
Posts: 10,566 (5.15/day)
Thanks: 4,238
Thanked 3,047 Times in 2,493 Posts
 |
Settings for q6700 With 350FSB 10x 1201 bios
:Extreme Tweaker:
AI Overclock Tuner CPU Ratio Settings FSB Strap To Northbridge [Auto] PCIe Frequency [105] Dram Frequency Dram Command Rate [2T] Dram Timing Control [Auto] Dram Static Read Control [Auto] AI Clock Twister [Light] Transaction Booster [Auto] CPU Voltage [1.475v] CPU Pll Voltage [1.7v] NB Voltage [1.45v] Dram Voltage [2.0v] FSB Termination Voltage [Auto] SB Voltage [1.075v] Loadline Calbration [Auto] CPU GTL Reference [Auto] NB GTL Reference [Auto] DDR2 Channel A Ref Voltage [Auto] DDR2 Channel B Ref Voltage [Auto] DDR2 Controller Ref Voltage [Auto] SB 1.5 Voltage [Auto]
__________________
The only way success is before work, is in the dictionary Support for the mind. Support for your hardware |
|
|
|
| The Following User Says Thank You to Cold Storm For This Useful Post: |
|
Jun 26, 2008, 12:18 AM
|
#13 |
|
Battosai
Join Date: Oct 2007
Location: In a library somewhere on this earth
Posts: 10,566 (5.15/day)
Thanks: 4,238
Thanked 3,047 Times in 2,493 Posts
|
Settings for Q6700 at 3.8 bench stable. 10x
:Extreme Tweaker:
AI Overclock Tuner CPU Ratio Settings FSB Strap To Northbridge [Auto] PCIe Frequency [105] Dram Frequency Dram Command Rate [2T] Dram Timing Control [Auto] Dram Static Read Control [Auto] AI Clock Twister [Light] Transaction Booster [Auto] CPU Voltage [1.6125v] CPU Pll Voltage [1.78v] NB Voltage [1.63v] Dram Voltage [2.10v] FSB Termination Voltage [1.6] SB Voltage [1.175v] Loadline Calbration [Auto] CPU GTL Reference [Auto] NB GTL Reference [Auto] DDR2 Channel A Ref Voltage [Auto] DDR2 Channel B Ref Voltage [Auto] DDR2 Controller Ref Voltage [Auto] SB 1.5 Voltage [1.55]
__________________
The only way success is before work, is in the dictionary Support for the mind. Support for your hardware |
|
|
|
| The Following User Says Thank You to Cold Storm For This Useful Post: |
|
Jul 16, 2008, 03:40 AM
|
#14 |
|
Staff
Join Date: Apr 2006
Location: Illinois, USA
Posts: 8,826 (3.40/day)
Thanks: 2,984
Thanked 3,297 Times in 2,522 Posts
|
Still messing around with the QX9650 at 400 MHz FSB. So far, 8x and 9x have been stable. Right now I am testing 9.5x 400 for 3.81 GHz (so far about 40 min Prime stable). I haven't changed much for settings, so I'll only list those:
Code:
Extreme Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 9 FSB Frequency : 400 FSB Strap to North Bridge : 400 DRAM Frequency: DDR2-800 CPU Voltage : 1.325v DRAM Voltage : 2.10 Loadline Calibration : Enabled  BTW, in reference to my post above, I placed a 45mm fan directly on the NB heatsink. Right now NB temps are only 49C under load, with stock NB voltage. Thinking about getting two or three 40mm fans and lining them up across the NB heatsink.
__________________
t_ski's stuff for sale ~ TPU Eyefinity Club ~ Heatware
Silverstone TJ07 build ~ Mini ITX Home Server build Intel i7 3930K ~ Asus P9X79 Pro ~ 4 x 8GB Corsair Dominator Platinum 1866 C9 ~ Triple 7970's with EK FC-7970 CSQ ~ Triple Asus VW246H LCD's ~ 2 x 120 GB Corsair Force 3 (Raid 0) ~ 500GB WD ~ Lite-On BluRay ~ Nickel-plated Heatkiller 3.0 CU ~ D5 with EK X-top ~ BIX Quad Rad ~ Corsair AX1200 ~ Silverstone TJ07 |
|
|
|
| The Following User Says Thank You to t_ski For This Useful Post: |
|
Jul 16, 2008, 04:04 AM
|
#15 |
 
|
Clock Settings for Q9450 @ 445*8 with Rampage 0403 BIOS
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO CPU Ratio Setting : 8 FSB Strap to North Bridge : AUTO FSB Frequency : 445 PCI-E Frequency: 110 DRAM Frequency: DDR2-890mhz DRAM Command Rate : 2N DRAM CLK Skew on Channel A: AUTO DRAM CLK Skew on Channel B: AUTO DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 12 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time : AUTO Write Recovery Time : AUTO Read to Precharge Time : AUTO Read to Write Delay (S/D) : AUTO Write to Read Delay (S) : AUTO Write to Read Delay (D) : AUTO Read to Read Delay (S) : AUTO Read to Read Delay (D) : AUTO Write to Write Delay (S) : AUTO Write to Write Delay (D) : AUTO 3rd Information WRITE to PRE Delay : AUTO READ to PRE Delay : AUTO PRE to PRE Delay : AUTO ALL PRE to ACT Delay : AUTO ALL PRE to REF Delay : AUTO DRAM Static Read Control: AUTO Ai Clock Twister : AUTO Transaction Booster : AUTO CPU Voltage : 1.4v CPU PLL Voltage : 1.61v North Bridge Voltage : 1.71v DRAM Voltage : 2.2v FSB Termination Voltage : 1.55v South Bridge Voltage : 1.05 SB 1.5V Voltage : 1.63v Loadline Calibration : Enabled CPU GTL Reference : 0.67X North Bridge GTL Reference : 0.67X DDR2 Controller REF Voltage : DDR2-REF DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO
__________________
|
|
|
|
| The Following User Says Thank You to MoeDaKilla For This Useful Post: |
|
Jul 19, 2008, 03:03 AM
|
#16 |
|
Staff
Join Date: Apr 2006
Location: Illinois, USA
Posts: 8,826 (3.40/day)
Thanks: 2,984
Thanked 3,297 Times in 2,522 Posts
|
Got it running at 3.81 GHz OCCT stable:
Code:
Extreme Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 9.5 FSB Frequency : 400 FSB Strap to North Bridge : 400 DRAM Frequency: DDR2-800 CPU Voltage : 1.375v DRAM Voltage : 2.10 Loadline Calibration : Enabled Code:
Extreme Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : 10 FSB Frequency : 400 FSB Strap to North Bridge : 400 DRAM Frequency: DDR2-800 CPU Voltage : 1.425v DRAM Voltage : 2.10 Loadline Calibration : Enabled Not sure if I need the full 1.425v for 4.0 GHz, but since I went up .05v going from 9 x 400 to 9.5 x 400, I figured that might be about right to start with. Next step is going to be 10.5 x 400 and 11 x 400, then trying to tweak the ram to run @ 500 & the FSB at 417 (so the ram is at 500). FORGOT TO ADD: I got tired of the whiney little 45mm fan, so I swapped it out with a 70mm fan from a stock AMD heatsink. This fan is a lot quieter, pushes more air, and has a thermal control built in. NB temp runs in the upper 30's to the lower 40's.
__________________
t_ski's stuff for sale ~ TPU Eyefinity Club ~ Heatware
Silverstone TJ07 build ~ Mini ITX Home Server build Intel i7 3930K ~ Asus P9X79 Pro ~ 4 x 8GB Corsair Dominator Platinum 1866 C9 ~ Triple 7970's with EK FC-7970 CSQ ~ Triple Asus VW246H LCD's ~ 2 x 120 GB Corsair Force 3 (Raid 0) ~ 500GB WD ~ Lite-On BluRay ~ Nickel-plated Heatkiller 3.0 CU ~ D5 with EK X-top ~ BIX Quad Rad ~ Corsair AX1200 ~ Silverstone TJ07 |
|
|
|
| The Following User Says Thank You to t_ski For This Useful Post: |
|
Jul 20, 2008, 07:20 AM
|
#17 |
|
Power User
Join Date: Oct 2006
Location: Western PA (Pittsburgh suburbs)
Posts: 18,129 (7.49/day)
Thanks: 450
Thanked 3,825 Times in 3,123 Posts
  |
Here's my settings for 4Ghz clocks. Doesn't take much in the ways of custom settings really. There's more to be had performance wise if I were to tune the ram. Just haven't found it necessary yet.
Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Setting : 10 FSB Strap to North Bridge : AUTO FSB Frequency : 400 PCI-E Frequency: 100 DRAM Frequency: DDR2-961mhz DRAM Command Rate : 2N DRAM CLK Skew on Channel A: AUTO DRAM CLK Skew on Channel B: AUTO DRAM Timing Control: Manual CAS# Latency : 4 RAS# to CAS# Delay : 4 RAS# Precharge : 4 RAS# ActivateTime : 12 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time : AUTO Write Recovery Time : AUTO Read to Precharge Time : AUTO Read to Write Delay (S/D) : AUTO Write to Read Delay (S) : AUTO Write to Read Delay (D) : AUTO Read to Read Delay (S) : AUTO Read to Read Delay (D) : AUTO Write to Write Delay (S) : AUTO Write to Write Delay (D) : AUTO 3rd Information WRITE to PRE Delay : AUTO READ to PRE Delay : AUTO PRE to PRE Delay : AUTO ALL PRE to ACT Delay : AUTO ALL PRE to REF Delay : AUTO DRAM Static Read Control: AUTO Ai Clock Twister : AUTO Transaction Booster : AUTO CPU Voltage : 1.425v CPU PLL Voltage : Auto North Bridge Voltage : 1.55v DRAM Voltage : 2.12v FSB Termination Voltage : Auto South Bridge Voltage : Auto SB 1.5V Voltage : Auto Loadline Calibration : Enabled CPU GTL Reference : Auto North Bridge GTL Reference : Auto DDR2 Controller REF Voltage : DDR2-REF DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO And here's 4.4Ghz. Didn't have to change anything but a couple voltages. Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Setting : 11 FSB Strap to North Bridge : AUTO FSB Frequency : 400 PCI-E Frequency: 100 DRAM Frequency: DDR2-961mhz DRAM Command Rate : 2N DRAM CLK Skew on Channel A: AUTO DRAM CLK Skew on Channel B: AUTO DRAM Timing Control: Manual CAS# Latency : 4 RAS# to CAS# Delay : 4 RAS# Precharge : 4 RAS# ActivateTime : 12 RAS# to RAS# Delay : AUTO Row Refresh Cycle Time : AUTO Write Recovery Time : AUTO Read to Precharge Time : AUTO Read to Write Delay (S/D) : AUTO Write to Read Delay (S) : AUTO Write to Read Delay (D) : AUTO Read to Read Delay (S) : AUTO Read to Read Delay (D) : AUTO Write to Write Delay (S) : AUTO Write to Write Delay (D) : AUTO 3rd Information WRITE to PRE Delay : AUTO READ to PRE Delay : AUTO PRE to PRE Delay : AUTO ALL PRE to ACT Delay : AUTO ALL PRE to REF Delay : AUTO DRAM Static Read Control: AUTO Ai Clock Twister : AUTO Transaction Booster : AUTO CPU Voltage : 1.6v CPU PLL Voltage : 1.74 North Bridge Voltage : 1.55v DRAM Voltage : 2.12v FSB Termination Voltage : 1.4v South Bridge Voltage : Auto SB 1.5V Voltage : Auto Loadline Calibration : Enabled CPU GTL Reference : Auto North Bridge GTL Reference : Auto DDR2 Controller REF Voltage : DDR2-REF DDR2 Channel A REF Voltage : AUTO DDR2 Channel B REF Voltage : AUTO
__________________
 Visit Ashentech “What the hell did you expect? Leave Vista under the pillow and the OS fairy would make it Win7?” -El Fiendo
“And Bring Mailman back god damnit, he is the Eric Cartman of TPU” -MRCL
Last edited by Wile E; Jul 20, 2008 at 08:44 PM. |
|
|
|
|
Jul 30, 2008, 10:11 AM
|
#18 |
 
Join Date: Dec 2004
Location: FIN
Posts: 284 (0.09/day)
Thanks: 44
Thanked 56 Times in 32 Posts
|
Here is mine .Board rampage formula Q6700 @3800mhz
Extreme Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : 9 Fsb strap to north bridge :auto FSB Frequency : 424 FSB Strap to North Bridge : auto PCI-E Frequency: 100 DRAM Frequency: DDR2-1063 DRAM Command Rate : auto DRAM CMD skew on channel A : auto DRAM CMD skew on channel B : auto DRAM CLK skew on channel A : auto DRAM CLK skew on channel A : auto DRAM Timing Control: auto DRAM Static Read Control: auto Ai Clock Twister : auto Ai transaction Booster : auto CPU Voltage : 1.41 CPU PLL Voltage : 1.62 North Bridge Voltage : auto DRAM Voltage : 2.1 FSB Termination Voltage : 1.42v South Bridge Voltage :auto Loadline Calibration : Enabled CPU GTL Reference : auto North Bridge GTL Reference : auto SB 1.5V Voltage : auto Cpu spread spectrum : Disabled Pcie spread spectrum : Disabled |
|
|
|
| The Following 2 Users Say Thank You to X800 For This Useful Post: |
|
Jul 30, 2008, 06:46 PM
|
#19 |
|
Senior Moderator
Join Date: Jul 2006
Location: Milwaukee, WI.
Posts: 31,879 (12.78/day)
Thanks: 2,779
Thanked 12,249 Times in 7,804 Posts
|
Running 4gb's of DDR2 1200 and I'm quite sure all is stable on that end. I got my Q6600 to 4ghz on my DFI P35 Dark, and I can't quite get it on my Rampage. Using 308 bios. I was using XP on the DFi and am using Vista on the Asus. I can get into Vista but Prime95 results in an immediate blue screen. I'd love any help on how to make this happen.
Extreme Tweaker Ai Overclock Tuner : Manual OC From CPU Level Up : AUTO CPU Ratio Control : Manual - Ratio CMOS Setting : x9 FSB Frequency : 450 FSB Strap to North Bridge : PCI-E Frequency: 100 DRAM Frequency: DDR2- 1199 DRAM Command Rate : 2T DRAM Timing Control: Manual CAS# Latency : 5 RAS# to CAS# Delay : 5 RAS# Precharge : 5 RAS# ActivateTime : 15 RAS# to RAS# Delay : A Row Refresh Cycle Time : A Write Recovery Time : A Read to Precharge Time : A Read to Write Delay (S/D) : A Write to Read Delay (S) : A Write to Read Delay (D) : A Read to Read Delay (S) : A Read to Read Delay (D) :A Write to Write Delay (S) :A Write to Write Delay (D) : A DRAM Static Read Control: A Ai Clock Twister : A Transaction Booster : A CPU Voltage : 1.58 (real) CPU PLL Voltage : A North Bridge Voltage : set at 1.59 DRAM Voltage : 2.2v FSB Termination Voltage : A South Bridge Voltage : A Loadline Calibration : Enabled CPU GTL Reference : A or x67 or x63 North Bridge GTL Reference : A or x67 DDR2 Channel A REF Voltage : A or DDR2_REF DDR2 Channel B REF Voltage : A DDR2 Controller REF Voltage : A SB 1.5V Voltage : A NB LED Selection : NB Volt SB LED Selection : SB Volt CPU LED Selection : CPU VOlt Voltiminder LED : CPU Spread Spectrum : Disabled PCIE Spread Spectrum : Disabled Advanced CPU Configuration CPU Ratio Control : Manual - Ratio CMOS Setting : C1E Suppport : Disabled CPU TM Function : Disabled Vanderpool Technology : Disabled Execute Disable Bit : Disabled Max CPUID Value Limit : Disabled USB Configuration USB Functions: Enabled Legacy USB Support : Disabled |
|
|
|
| The Following User Says Thank You to erocker For This Useful Post: |
|
Sep 1, 2008, 03:20 PM
|
#20 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
added a bios link to the top page http://support.asus.com/download/dow...Language=en-us for bios 408 if you update some tweaks are different than 403, one I noticed is set twister to lighter to get a higher fsb.
|
|
|
|
|
Dec 28, 2008, 10:29 PM
|
#21 |
|
Eligible for custom title
Join Date: May 2006
Posts: 10,186 (3.97/day)
Thanks: 1,578
Thanked 1,135 Times in 960 Posts
|
any new updates add them here
|
|
|
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Overclocking is Easy! Get Results! | Kursah | Overclocking & Cooling | 131 | May 12, 2010 12:14 AM |
| ASUS A8R32-MVP Deluxe | W1zzard | Reviews | 11 | Oct 25, 2008 11:43 AM |
| Asus M2a-vm | W1zzard | Reviews | 7 | Jan 30, 2008 04:05 PM |
| ASUS Announces Spider Platform | Jimmy 2004 | News | 9 | Nov 21, 2007 10:32 AM |
| ASUS CT-479 Adapter | Urlyin | Reviews | 8 | Dec 4, 2005 04:41 PM |
System Specs
