1. Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Aerocool Launches the Strike-X One & Strike-X One Advance PC cases

Discussion in 'News' started by Cristian_25H, Feb 9, 2012.

  1. Cristian_25H

    Cristian_25H News Poster

    Joined:
    Dec 6, 2011
    Messages:
    4,626 (4.16/day)
    Thanks Received:
    1,164
    Location:
    Still on the East Side
    Taiwan-based Aerocool Advanced Technologies has just announced the European release of two new Strike-X Series mid-tower PC cases, the Strike-X One and Strike-X One Advance. Both models feature a steel structure, are painted black both inside and out, and have support for ATX and micro ATX motherboards, four 5.25-inch drive bays (with tool-free mounting systems), six 3.5-inch internal bays, a PSU dust filter, and pre-drilled holes for watercooling tubes and cables.

    The Strike-X One has an I/O panel with two USB 2.0 ports, and is equipped with one 120 mm rear fan, while the Strike-X One Advance comes with two USB 3.0 ports, a 120 mm rear fan, and a front 120 mm fan with red LEDs. The Strike-X One and Strike-X One Advance cost 34.99 Euro and 39.99 Euro, respectively.

    [​IMG] [​IMG] [​IMG] [​IMG] [​IMG]
     
  2. THE_EGG

    THE_EGG

    Joined:
    Dec 15, 2011
    Messages:
    1,564 (1.42/day)
    Thanks Received:
    530
    Location:
    Brisbane QLD, Australia
    I'm sure Xigmatek will have something to say about the front panel design...
     
  3. FreedomEclipse

    FreedomEclipse ~Technological Technocrat~

    Joined:
    Apr 20, 2007
    Messages:
    14,044 (5.01/day)
    Thanks Received:
    2,425
    I was gonna say Xclio might have a problem with it too but the last time Xclio made a case with an X in it, i was still in highschool
     
  4. THE_EGG

    THE_EGG

    Joined:
    Dec 15, 2011
    Messages:
    1,564 (1.42/day)
    Thanks Received:
    530
    Location:
    Brisbane QLD, Australia
    It does look like you get a LOT of kit for the money though. Although the paint on my last Aerocool Case (Aerocool M40), decided to shed its skin after 2 years and I had to repaint it. (although i was planning to repaint it anyway.)
     
  5. _JP_

    _JP_

    Joined:
    Apr 16, 2010
    Messages:
    2,684 (1.57/day)
    Thanks Received:
    740
    Location:
    Portugal
    Why, upon glancing at the 1st image, did I get the feel that something was not right, that this chassis should be orange and Xigmatek?
     
  6. Vancha

    Joined:
    Jun 18, 2010
    Messages:
    359 (0.22/day)
    Thanks Received:
    62
    I don't think even Xigmatek could make something look that tacky.
     
  7. pantherx12

    pantherx12 New Member

    Joined:
    Jan 2, 2009
    Messages:
    9,714 (4.45/day)
    Thanks Received:
    1,699
    Location:
    ENGLAND-LAND-LAND
    I was going to say "not bad" but then I saw the big X on the front.

    Way to completely ruin a case.
     
  8. _JP_

    _JP_

    Joined:
    Apr 16, 2010
    Messages:
    2,684 (1.57/day)
    Thanks Received:
    740
    Location:
    Portugal
    I don't think so either, but it was the 1st that came to my mind.
    You could just chop it off.
     
  9. pantherx12

    pantherx12 New Member

    Joined:
    Jan 2, 2009
    Messages:
    9,714 (4.45/day)
    Thanks Received:
    1,699
    Location:
    ENGLAND-LAND-LAND
    For once I want a case that I don't have to chop up :laugh:
     
    _JP_ says thanks.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guest)

Share This Page