1. Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Hybrid cooled SR-2 in Level10

Discussion in 'Project Logs' started by HybridChiller, Jan 14, 2011.

  1. Cold Storm

    Cold Storm Battosai

    Joined:
    Oct 7, 2007
    Messages:
    15,014 (5.95/day)
    Thanks Received:
    2,999
    Location:
    In a library somewhere on this earth
    Thanks for the update. Looking good!
  2. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    i'm going to fill up the loop now the 3th pump is installed, own mixture : 25% Ethylene Glycol and 75% PURE water, no demi.

    what you see in the measure cup is the Glycol no color pure 100% glycol :

    [​IMG]

    here my koolanc poor in cup on the ZERN res with a snake connector to make it a little bit eassier to fill :

    [​IMG]

    on the drain valve i putted also a tube in a bus filled with my mixture, where the pump can draw it's liquid from when i put the valve open, to make it a little bit eassier to lol :

    [​IMG]

    [​IMG]

    and here comes the first liquid lol, pumps are now running to get the last micro bubbles out the loop, for now, no leaks found :

    [​IMG]
    Black Haru, Flibolito and HammerON say thanks.
  3. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
  4. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    It's a miracle !!!!

    i get it closed hahahahaha, +200m cable in limited room of 3,5cm lol :

    [​IMG]

    here you see that the plate is a little round, but i put the cable fast fast in to look if i get it closed,
    later on the cable will be nice routed and strapped so that the plate doesn't look round :

    [​IMG]
  5. GENTLEMEN New Member

    Joined:
    Jun 18, 2010
    Messages:
    198 (0.13/day)
    Thanks Received:
    21
    Location:
    Philippines
    Only one word can describe this build: EPIC
    Me likey the 90 degree connectors and the "flame" ram.
    THIS is what a Level 10 should look like.
    HybridChiller says thanks.
  6. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    last minute adjustment for the vga's :

    [​IMG]

    [​IMG]
  7. Yukikaze

    Yukikaze

    Joined:
    Sep 24, 2008
    Messages:
    2,310 (1.06/day)
    Thanks Received:
    481
    OH MY GOD.

    ***bows deeply***

    You, sir, are a master!

    This is easily the best built PC I've seen in my life, and then some. It utterly destroys just about any other mod I've seen.
    HybridChiller says thanks.
  8. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    little update :

    [​IMG]

    [​IMG]

    [​IMG]
  9. HammerON

    HammerON The Watchful Moderator Staff Member

    Joined:
    Mar 2, 2009
    Messages:
    6,481 (3.22/day)
    Thanks Received:
    3,585
    Thanks for all the cool updates:toast:

    Can't wait to see what it looks like with the gpu(s):)
    Crunching for Team TPU
  10. arnoo1

    Joined:
    Oct 15, 2009
    Messages:
    745 (0.42/day)
    Thanks Received:
    124
    Location:
    Netherlands
    19c cpu? Should be lower right?
  11. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    when the liquid is 20°C, the cores will always be a little bit hotter.

    so my liquid is 15°C, and core is 19°C
  12. mATrIxLord New Member

    Joined:
    Feb 18, 2010
    Messages:
    88 (0.05/day)
    Thanks Received:
    22
    this is simply awesome!!! keep the good work!
    HybridChiller says thanks.
  13. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    here an update of my temps with OC :

    [​IMG]
    Cold Storm says thanks.
  14. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    here are the load temps, cpu temp in Coolit software is not correct, cpu isn't supported by the coolit software.

    As you see idle the coolers run lower power, when stressed the coolers will raise there cooling power, and keep the liquid temp low, under Ambient,
    cpu temp raises a 5 a 6°C from idle to load thanks to temp controlled coolers.

    Temp of liquid is set @ 22°C max, min power of coolers @ 60%, max power @ 100%, real nice settings on these coolers,
    and the coolers don't even run at 100% to keep the temp, for me that's good for lower noise level :

    [​IMG]
  15. ERazer

    ERazer

    Joined:
    Oct 8, 2009
    Messages:
    1,543 (0.86/day)
    Thanks Received:
    492
    Location:
    Republic of Texas
    i feel like i need pay for a ticket to watch this build, simply awsome:respect:
    HybridChiller says thanks.
  16. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    little sneakpeak what i'm doing now :

    Most of the time, people put there powercable for vga like the RED arrows.
    I whant it as clean as possible in this case, en i will do my powercables like the GREEN arrow, straight horizontal with the vga's.
    Vga's seems like they are floating in the air lol, strange sight.

    On later time i can mod also the plastic cap on the vga, make it wider, little bit bigger, so the powercables are IN the plastic cap of the vga cooler, totally NOT visible.

    [​IMG]

    And this is the beginning of this little vga mod :

    [​IMG]
    Cold Storm says thanks.
  17. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    Am working now on the last mem flames, did the cables in the backpanel better now, so the back-panel is not round anymore,
    and made some led's for give light to the mem modules :

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
    Cold Storm says thanks.
  18. BababooeyHTJ New Member

    Joined:
    Apr 6, 2009
    Messages:
    907 (0.46/day)
    Thanks Received:
    85
    This really is just crazy. Awesome work, man.
    HybridChiller says thanks.
  19. Dia01

    Dia01 New Member

    Joined:
    Sep 14, 2006
    Messages:
    498 (0.17/day)
    Thanks Received:
    54
    Location:
    QLD, Australia
    I've got to say, this is one of the most entertaining build logs I have read for some time, keep it up! :cool:
    HybridChiller says thanks.
  20. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    the revodriveX2 960Gb is coming next month,
    and tomorrow the Killer 2100 arrives.

    if possible also mod the networkcard
  21. l3p

    l3p

    Joined:
    Oct 22, 2010
    Messages:
    309 (0.22/day)
    Thanks Received:
    638
    Location:
    Netherlands
    Nice !
  22. HybridChiller

    HybridChiller New Member

    Joined:
    Jan 14, 2011
    Messages:
    84 (0.06/day)
    Thanks Received:
    116
    Location:
    cloud of ln²
    Killer2100 eifinally in the house,
    original cover removed for modding it,
    and here a pic of the killer2100 in operation with two red led's, what fits very good in the theme :

    [​IMG]
  23. blu3flannel

    blu3flannel

    Joined:
    May 14, 2010
    Messages:
    898 (0.57/day)
    Thanks Received:
    120
    Location:
    NYU
    Sheer. Beauty. :twitch:
    :respect::respect::respect:
    HybridChiller says thanks.
  24. X800

    X800

    Joined:
    Dec 24, 2004
    Messages:
    294 (0.08/day)
    Thanks Received:
    55
    Location:
    FIN
    Outstanding work.Just amazing :rockout:
    HybridChiller says thanks.
  25. pantherx12

    pantherx12 New Member

    Joined:
    Jan 2, 2009
    Messages:
    9,714 (4.70/day)
    Thanks Received:
    1,699
    Location:
    ENGLAND-LAND-LAND
    Nice, whilst I just sold a Coolit Tec system ( for cheap I think) makes me want to mess with tecs again.

    Only this time fully custom.

    Got some mad ideas but don't have the money or tools to do so : [

    So looking at nice mods like this will have to do for now.
    HybridChiller says thanks.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guest)

Share This Page