1. Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

PALiT 9600GSO voltage mods

Discussion in 'NVIDIA' started by largon, Jul 19, 2008.

  1. largon

    largon

    Joined:
    May 6, 2005
    Messages:
    2,784 (0.74/day)
    Thanks Received:
    433
    Location:
    Tre, Suomi Finland
    quadomatic,
    The mods in this thread do not apply to eVGA 9600GSO.

    BUT!
    Since 9600GSO is the same as 8800GS and eVGA appears to be using nVIDIA's reference board the mods for reference 8800GS described here should apply to an eVGA 9600GSO too.
     
    Last edited: Sep 15, 2008
    quadomatic says thanks.
  2. quadomatic New Member

    Joined:
    May 22, 2005
    Messages:
    86 (0.02/day)
    Thanks Received:
    0
    Location:
    Chicago, IL USA
    AWESOME! I'm going to check this for sure.

    I appreciate this a lot!

    UPDATE: went through - so the mods achieve the same things as they do on the Palit, cept you just do different stuff. Any clue whether my results will be similar to these?...err, well I'd be on the dual slot air cooler though. How much of an oc could I probably get with the dual-slot air cooler? What cooler should I buy to replace it if I want better results (would it be worth it to replace the cooler?)? 900/1135/2250 would probably be pushing it on air, huh?

    Someone said this on newegg about the card:
    Is that good or bad?
     
    Last edited: Sep 15, 2008
  3. largon

    largon

    Joined:
    May 6, 2005
    Messages:
    2,784 (0.74/day)
    Thanks Received:
    433
    Location:
    Tre, Suomi Finland
  4. Leopard New Member

    Joined:
    Oct 17, 2008
    Messages:
    2 (0.00/day)
    Thanks Received:
    0
    Hi!

    I also have this card. Before I go berserk with my soldering iron, is there a more simple pencil mod available for this particular card? I'm looking for a vGPU pencil mod if you need more accurate info. It would be easier since I would not have to go and buy any resistors. The nearest electronics shop is ~50km from my home so... ;)

    Thanks in advance!
     
  5. DOM

    DOM

    Joined:
    May 30, 2006
    Messages:
    7,551 (2.23/day)
    Thanks Received:
    828
    Location:
    TX, USA
    which card ? Palit ?
     
  6. Leopard New Member

    Joined:
    Oct 17, 2008
    Messages:
    2 (0.00/day)
    Thanks Received:
    0
    Yep, the Palit 9600GSO 384MB Sonic.
     
  7. DOM

    DOM

    Joined:
    May 30, 2006
    Messages:
    7,551 (2.23/day)
    Thanks Received:
    828
    Location:
    TX, USA
    well I dont think theres a pencil mod available and the mod was easy, it the 1st card I volt modded
     
  8. largon

    largon

    Joined:
    May 6, 2005
    Messages:
    2,784 (0.74/day)
    Thanks Received:
    433
    Location:
    Tre, Suomi Finland
    Pencil mod might be possible but I can't do anything about it cause I don't have the card so I can't pinpoint the resistor to pencil. There's a resistor somewhere in there that connects ground and the trace between the optional soldering points (red dots)...
     

Currently Active Users Viewing This Thread: 1 (0 members and 1 guest)

Share This Page