1. Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

RAM timings

Discussion in 'Motherboards & Memory' started by Taz100420, Jan 3, 2007.

  1. Taz100420

    Taz100420

    Joined:
    Oct 26, 2006
    Messages:
    1,929 (0.66/day)
    Thanks Received:
    100
    Location:
    Fremont, Ohio
    mem.JPG

    attached is my CPU-Z mem timings and was wondering if they are alright, cause as of now its stable and was wondering if I can go higher?

    plus im kinda new to mem timings
     
  2. Taz100420

    Taz100420

    Joined:
    Oct 26, 2006
    Messages:
    1,929 (0.66/day)
    Thanks Received:
    100
    Location:
    Fremont, Ohio
    oh and Im using a cheapo stick I found in all my stuff lol
     
  3. mortal New Member

    Joined:
    Sep 2, 2006
    Messages:
    151 (0.05/day)
    Thanks Received:
    7
    Location:
    Croatia - Umag
    you can try go higher, you wont break it. Give it a bit more juice and try.

    Lower latencies on pentium are meaningless so try to go with higher frequencies
     
  4. Taz100420

    Taz100420

    Joined:
    Oct 26, 2006
    Messages:
    1,929 (0.66/day)
    Thanks Received:
    100
    Location:
    Fremont, Ohio
    give it more voltage?
     
  5. mortal New Member

    Joined:
    Sep 2, 2006
    Messages:
    151 (0.05/day)
    Thanks Received:
    7
    Location:
    Croatia - Umag
    Yes, you wont damage it with little more. Then try to OC it in bios.
     
  6. Taz100420

    Taz100420

    Joined:
    Oct 26, 2006
    Messages:
    1,929 (0.66/day)
    Thanks Received:
    100
    Location:
    Fremont, Ohio
    well its at 2.6v should I raise it by .1 v
     
  7. Brother Esau New Member

    Joined:
    Jan 6, 2007
    Messages:
    98 (0.03/day)
    Thanks Received:
    0
    Location:
    The Dark Side of The Moon
    Don't know what kind of set up you have dude and you should really list one before asking for help. But on my set up I have my ram running at DDR540 200:1:! and at stock Mushkin recommends 2.60v and at my speeds I only increased it by 2.64v

    Genie BIOS Settings

    FSB Bus Frequency............................. - 270
    LDT/FSB Frequency Ratio....................... - x3
    CPU/FSB Frequency Ratio....................... - 10
    PCI eXpress Frequency......................... - 105Mhz

    CPU VID StartUp Value......................... - Start up

    CPU VID Control............................... - 1.375
    CPU VID Special Control....................... - auto
    LDT Voltage Control........................... - 1.20v
    Chip Set Voltage Control...................... - 1.52
    DRAM Voltage Control.......................... - 2.64v
    DRAM Configuration Settings:

    DRAM Frequency Set............................ - 200:1:1
    Command Per Clock (CPC)....................... - Enable
    CAS Latency Control (Tcl)..................... - 3
    RAS# to CAS# delay (Trcd)..................... - 3
    Min RAS# active time (Tras)................... - 8
    Row precharge time (Trp)...................... - 2
    Row Cycle time (Trc).......................... - 8 Bus Clocks
    Row refresh cyc time (Trfc)................... - 15 Bus Clocks
    Row to Row delay (Trrd)....................... - 02 Bus Clocks
    Write recovery time (Twr)..................... - 02 Bus Clocks
    Write to Read delay (Twtr).................... - 01 Bus Clocks
    Read to Write delay (Trwt).................... - 03 Bus Clocks
    Refresh Period (Tref)......................... - 4708 Cycles
    DRAM Bank Interleave.......................... - Enabled

    DQS Skew Control.............................. - Auto
    DQS Skew Value................................ - 0
    DRAM Drive Strength........................... - 8
    DRAM Data Drive Strength...................... - 2
    Max Async Latency............................. - 7
    DRAM Response Time............................ - normal
    Read Preamble Time............................ - 5.5
    IdleCycle Limit............................... - 64 Cycles
    Dynamic Counter............................... - Enable
    R/W Queue Bypass.............................. - 16 x
    Bypass Max.................................... - 07 x
    32 Byte Granularity........................... - Disable(4 Bursts)



    ==========
     
  8. Frogger

    Frogger

    Joined:
    Feb 12, 2006
    Messages:
    2,180 (0.68/day)
    Thanks Received:
    313
    it's safe to push it to 2.7 for sure will prob take 2.8 an you can push the clocks on it to around 190 with those timeings
     
  9. Brother Esau New Member

    Joined:
    Jan 6, 2007
    Messages:
    98 (0.03/day)
    Thanks Received:
    0
    Location:
    The Dark Side of The Moon
    Like I said dude its kind of hard for people tio help you if we don't know what kind of componenets you are working with....Do that first and I will help you out!
     
  10. Taz100420

    Taz100420

    Joined:
    Oct 26, 2006
    Messages:
    1,929 (0.66/day)
    Thanks Received:
    100
    Location:
    Fremont, Ohio
    well i decided im ditching this stick and getting mushkin 1GB (2X 512MB dual channel) for now until I get a new mobo with crossfire and DDR2
     
  11. WarEagleAU

    WarEagleAU Bird of Prey

    Joined:
    Jul 9, 2006
    Messages:
    10,797 (3.56/day)
    Thanks Received:
    546
    Location:
    Gurley, AL
    Good for you. I have Infineon Memory with their chips (or hynix one, but I think they are infineon chips) and Ketxxx gave me some timings to use. Turned out, they froze me up ROFL. Probably needed to up the voltage just a little.
     

Currently Active Users Viewing This Thread: 1 (0 members and 1 guest)

Share This Page