CPU- Intel i7 920...MOBO- Foxconn Bloodrage...RAM- 6gig G-skill DDR3 1600...HDD- Western Digital 500gig...GPU's- EVGA GTX 285's...PSU- Enermax Revolution 1050 watt...Case- Lian Li A77B...Cooling- Swiftech cpu block-GTZ...Swiftech 3X120mm radiator...Swiftech MCP655 pump...8-120mm fans. Headphones- Sennheiser PC350's
Performed Mods:
Cut holes in mobo tray for wire management. Painted mobo tray. Installed LED fans and lights, also added a PSU case extension for extra room in side the case. Radiator is velcro'd to top of case, it is VERY SECURE! :) ALL COMMENTS WELCOME!
Hey thanks guys. This is my first serious attempt at wire management. lol. I did manage to get all of the psu wires routed behind the mobo tray leaving only the header panel wires in front. As far as the light on the controller, for some odd reason i was under the impression they were all red. SUPRISE! They weren't. And the middle light never worked. I would like to get a contoller with no lights. But that's pretty much impossible.
pentastar111Hey thanks guys. This is my first serious attempt at wire management. lol. I did manage to get all of the psu wires routed behind the mobo tray leaving only the header panel wires in front. As far as the light on the controller, for some odd reason i was under the impression they were all red. SUPRISE! They weren't. And the middle light never worked. I would like to get a contoller with no lights. But that's pretty much impossible.
freaksaviorHOLY CRAP!! 2.25 per foot!!! is it gold lined?
damn!
It is a little pricey,BUT....the stuff I used; the tubing with the dull finish, does not kink that easy. It is worth the price. And it's only $1.50 a foot.
I like how the red tubes match your motherboard. Great hardware, clean paint job and I think you did a good job on the cable management. Awesome case mod 8/10
My only con is the velcro on top. It is a good idea for quick and easy modding, but not a clean look to me. I would put a little more time and done pin clips or push clips (since you still want to be able to remove the radiator).
t77snapshotI like how the red tubes match your motherboard. Great hardware, clean paint job and I think you did a good job on the cable management. Awesome case mod 8/10
My only con is the velcro on top. It is a good idea for quick and easy modding, but not a clean look to me. I would put a little more time and done pin clips or push clips (since you still want to be able to remove the radiator).
The velcro looks alot better in person than in the pic's that's for sure...I'll check out the clip or push clip idea you have. Thanks for the input.
Bjorn_Of_IcelandVery nice red tubes! :)~ and its better than pouring filthy dyes on the water. So when will the Fourth come?
Sweer specs also. This is superb pentastar!
Thanks Bjorn. And the forth will be here in the next year and a half. I hope AMD mobo makers can come up with some cooler boards by then as I would like to do a none Intel rig this next time.
A suggestion though, you can turn the pump upright so that the tube going from the res to pump is in a straight form instead of cruved, and if you can fit the rad inside, do so.. with a case that big, a rad sitting on top is kinda awkward. With tubes sticking out with irregular bends..
Excelent work, except the rad on top of course:) but I had made worse... Anyway, consider mounting it vertically, behind the case, on some 3 inch (or more) spacers; apart from the aestetics, it will make the filling job easier. And I hope you never use pure water! :) 8/10 from me!
PS: the elbows can be found cheaper at the gardening tools in supermarket, are used also for the water hoses and stuff; mainly fit 1/2 inch hoses and even smaller with a bit of stretch :D!
32 Comments on The Third(No revisions)
However, my only snags are the blue LEDs in fan controller & the cable management.
8/10
:rockout:
Otherwise, freaking sick set up, nicely done and well maintained.
mine's clear with red die and its stained my res :(
check mine out forums.techpowerup.com/showthread.php?t=83948
but rate here
forums.techpowerup.com/showthread.php?t=52816
www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=59_413_292&products_id=4184 this tubing is great stuff. Although it would be wise to use either one size smaller clamps if you go with plastic clamps or use fully adjustable metal clamps as this tubing fits a hair loose. As far as the dye staining goes, that's why I went with the "colored" tubing and clear coolant...The rig I did in blue is really stained... :(
damn!
My only con is the velcro on top. It is a good idea for quick and easy modding, but not a clean look to me. I would put a little more time and done pin clips or push clips (since you still want to be able to remove the radiator).
Sweer specs also. This is superb pentastar!
by the way 10
Congrats!!!
This is not a negative comment, I gave you a 9 only because you need to really wow me to get a 10. Very clean and cool looking build :)
Apogee GTZ is a plus, my favo block!
i'd say 9/10
and it will be perfect if those cables re-arranged?
I like to be able hide-and-seek the cables as your you have done xD, is brilliant your hardware, very good tubes
very nice,clean built..and love the color combination too..you've done an excellent job here..
PS: the elbows can be found cheaper at the gardening tools in supermarket, are used also for the water hoses and stuff; mainly fit 1/2 inch hoses and even smaller with a bit of stretch :D!
www.techpowerup.com/gallery/2508.html
8/10