Relinquish
New Member
- Joined
- Jan 10, 2011
- Messages
- 126 (0.03/day)
Processor | i5 2500K @ 4.6 1.397 |
---|---|
Motherboard | Gigabyte GA-Z68X-UD3P-B3 |
Cooling | GELID Tranquillo with sickleflow 1800RPM |
Memory | 8GB G.Skill 1600Mhz CL9 |
Video Card(s) | AMD Radeon 6950 unlocked to 6970 |
Storage | 120GB Intel 320 SSD |
Power Supply | OCZ Fatal1ty 550W Modular PSU |
Software | Windows 8 |
Hello,
I have a Gigabyte GA-Z68X-UD3P-B3 motherboard and I'm having problems with the CPU voltage being set by the motherboard.
I realized that after a week of overclocking my 2500K to 4.5Ghz, the Vcore was actually being set at 1.36V and not the 1.3V I thought it was being set at (CPUZ says the voltage is 1V all the time so I thought nothing of it.) The only way to get some sort of reading in windows is to use the touch BIOS utility.
So here are my settings:
Multi/Ratio : 45X
Turbo: Disabled
C1E/C5/C6 and any other power saving feature: enabled.
Internal PLL: Disabled.
LLC: Level 5
VID: Normal (Auto wants to set it at 1.36V for a 45X multi)
Dynamic VID: +0.055V
So for this gigabyte board the 'normal' setting allows me to use an offset voltage (Dynamic VID) or I can manually set the voltage I want by changing that. Default is Auto. The Base CLK runs at 100.3Mhz as standard.
So here's the thing. I want to use offset so that when the clock speeds are scaled down in idle, the voltage does so too but it doesn't go so low as to cause any BSODs. Under load the voltage goes straight up to 1.36V and will stay there until the clock speeds back down. What I don't understand is the BIOS I think actually sets the VCORE to 1.36 and supposedly uses the offset to alter that but I should be seeing in that case voltages of over 1.4V. Changing the offset to +0.050V does nothing, except lowers the VCORE to 1.34 for a millisecond but the majority of the time it is set to 1.36V. I've tried -ve offsets but the system won't boot then.
Upping the LLC doesn't help either. For example if I put the LLC to Level 6 it will put 1.38V through the chip sometimes under load For that voltage I would expect to be running it at 4.7Ghz or more but for 4.5 it's too much. Plus I don't need to have it at 4.7. What I did try was manual voltage settings and I got mixed success.
I found that having the VCORE set manually to 1.315V was able to get be stable at 4.5Ghz. Great you'd say? Well no. That 1.315V translates to 1.33V actually being set which can spike up to 1.36 (what is their obsession with 1.36V lol?). So back to square one. Also a manual VCORE of 1.32V actually translates to 1.36V. So its bad enough I have to run it at load with this voltage but I don't want to be running it 1.36V @ 1600Mhz
I just need to know if I have to RMA this board because the guy who I spoke to on the phone from the company I bought this from (overclockers UK) wanted me to see if other people are experiencing the same thing. I'm of the opinion that I need an RMA but what do you guys think?
Thanks for reading.
I have a Gigabyte GA-Z68X-UD3P-B3 motherboard and I'm having problems with the CPU voltage being set by the motherboard.
I realized that after a week of overclocking my 2500K to 4.5Ghz, the Vcore was actually being set at 1.36V and not the 1.3V I thought it was being set at (CPUZ says the voltage is 1V all the time so I thought nothing of it.) The only way to get some sort of reading in windows is to use the touch BIOS utility.
So here are my settings:
Multi/Ratio : 45X
Turbo: Disabled
C1E/C5/C6 and any other power saving feature: enabled.
Internal PLL: Disabled.
LLC: Level 5
VID: Normal (Auto wants to set it at 1.36V for a 45X multi)
Dynamic VID: +0.055V
So for this gigabyte board the 'normal' setting allows me to use an offset voltage (Dynamic VID) or I can manually set the voltage I want by changing that. Default is Auto. The Base CLK runs at 100.3Mhz as standard.
So here's the thing. I want to use offset so that when the clock speeds are scaled down in idle, the voltage does so too but it doesn't go so low as to cause any BSODs. Under load the voltage goes straight up to 1.36V and will stay there until the clock speeds back down. What I don't understand is the BIOS I think actually sets the VCORE to 1.36 and supposedly uses the offset to alter that but I should be seeing in that case voltages of over 1.4V. Changing the offset to +0.050V does nothing, except lowers the VCORE to 1.34 for a millisecond but the majority of the time it is set to 1.36V. I've tried -ve offsets but the system won't boot then.
Upping the LLC doesn't help either. For example if I put the LLC to Level 6 it will put 1.38V through the chip sometimes under load For that voltage I would expect to be running it at 4.7Ghz or more but for 4.5 it's too much. Plus I don't need to have it at 4.7. What I did try was manual voltage settings and I got mixed success.
I found that having the VCORE set manually to 1.315V was able to get be stable at 4.5Ghz. Great you'd say? Well no. That 1.315V translates to 1.33V actually being set which can spike up to 1.36 (what is their obsession with 1.36V lol?). So back to square one. Also a manual VCORE of 1.32V actually translates to 1.36V. So its bad enough I have to run it at load with this voltage but I don't want to be running it 1.36V @ 1600Mhz
I just need to know if I have to RMA this board because the guy who I spoke to on the phone from the company I bought this from (overclockers UK) wanted me to see if other people are experiencing the same thing. I'm of the opinion that I need an RMA but what do you guys think?
Thanks for reading.