• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Are my i7 3930k temps too high?

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
I was lazy this time around and had a system built for me with an i7-3930k conservatively overclocked to 4000MHz. I've been testing my temps with real temp and prime and they seem very hot to me. The system is water cooled with an Asetek 570LC, which is a closed system with two 120mm fans running push/pull at a fixed(3-pin connectors) 1400rpm. See below for the temps. The manufacturer is telling me the temps are fine, but 86'C o/c and 77'C stock seems very hot for water cooling. At idle the hottest core is around 39'C. The ambient room temp is around 23'C.

Are these temps ok? If not, what do you suggest? Remount the heatsink with new thermal paste? Faster 4-pin fans with controllable speeds? Recommendations for paste and fans would be welcome if that's what you think I need.

The system is built on an ASUS Rampage IV Extreme with Win7 64 Pro.

Thanks for any advice.

Here is Real Temp calibration with Prime run at small FFT and my 3930 overclocked to 4000MHz:


Here is the same with the 3930 run at stock for comparison:
 
Joined
Dec 31, 2009
Messages
19,366 (3.73/day)
Benchmark Scores Faster than yours... I'd bet on it. :)
Seems fine for the sub par cooler... yep. Its a Hex core 125W CPU with a 120mm rad. Faster fans will help, but to what end? More noise, more money, for a couple less C? If that is worth it to you, go get some new fans. :)
 
Joined
May 14, 2009
Messages
2,132 (0.39/day)
Location
Chicago burbs
System Name Halloween Boo!
Processor Intel Core i7 3770K
Motherboard Gigabyte Z77-Up7
Cooling Custom Water/ Thermalchill TA 120.3/ Swiftech Apogeee XT/ MCP655/ Swiftech M icrores/ XSPC RX 240
Memory 16G G.Skill trident 2400MHz
Video Card(s) 3 x Radeon 7970
Storage OCZ Revo Drive 240G
Display(s) 24 inch Viewsonic
Case Phobia WayCoolIt Test Bench
Power Supply Nexus 1100 watt
A dumb question. What voltage?
 

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
Seems fine for the sub par cooler... yep. Its a Hex core 125W CPU with a 120mm rad. Faster fans will help, but to what end? More noise, more money, for a couple less C? If that is worth it to you, go get some new fans. :)

Thanks for the reply. So the thermal compound is probably ok? Will this amount of cooling be ok for gaming and maybe some video encoding work assuming I stay with the conservative overclock?
 
Joined
May 14, 2009
Messages
2,132 (0.39/day)
Location
Chicago burbs
System Name Halloween Boo!
Processor Intel Core i7 3770K
Motherboard Gigabyte Z77-Up7
Cooling Custom Water/ Thermalchill TA 120.3/ Swiftech Apogeee XT/ MCP655/ Swiftech M icrores/ XSPC RX 240
Memory 16G G.Skill trident 2400MHz
Video Card(s) 3 x Radeon 7970
Storage OCZ Revo Drive 240G
Display(s) 24 inch Viewsonic
Case Phobia WayCoolIt Test Bench
Power Supply Nexus 1100 watt
Thanks for the reply. So the thermal compound is probably ok? Will this amount of cooling be ok for gaming and maybe some video encoding work assuming I stay with the conservative overclock?

Sandybridge E should be kept under load 80 or less to be safe.
 

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
Joined
May 14, 2009
Messages
2,132 (0.39/day)
Location
Chicago burbs
System Name Halloween Boo!
Processor Intel Core i7 3770K
Motherboard Gigabyte Z77-Up7
Cooling Custom Water/ Thermalchill TA 120.3/ Swiftech Apogeee XT/ MCP655/ Swiftech M icrores/ XSPC RX 240
Memory 16G G.Skill trident 2400MHz
Video Card(s) 3 x Radeon 7970
Storage OCZ Revo Drive 240G
Display(s) 24 inch Viewsonic
Case Phobia WayCoolIt Test Bench
Power Supply Nexus 1100 watt
Probably should have included that. Only running at 1.22V.

Thats high IMO even with your cooler. Is the heatsink applied correctly including TIM plus where is the rad. Take a photo.
 

MxPhenom 216

ASIC Engineer
Joined
Aug 31, 2010
Messages
12,944 (2.62/day)
Location
Loveland, CO
System Name Ryzen Reflection
Processor AMD Ryzen 9 5900x
Motherboard Gigabyte X570S Aorus Master
Cooling 2x EK PE360 | TechN AM4 AMD Block Black | EK Quantum Vector Trinity GPU Nickel + Plexi
Memory Teamgroup T-Force Xtreem 2x16GB B-Die 3600 @ 14-14-14-28-42-288-2T 1.45v
Video Card(s) Zotac AMP HoloBlack RTX 3080Ti 12G | 950mV 1950Mhz
Storage WD SN850 500GB (OS) | Samsung 980 Pro 1TB (Games_1) | Samsung 970 Evo 1TB (Games_2)
Display(s) Asus XG27AQM 240Hz G-Sync Fast-IPS | Gigabyte M27Q-P 165Hz 1440P IPS | Asus 24" IPS (portrait mode)
Case Lian Li PC-011D XL | Custom cables by Cablemodz
Audio Device(s) FiiO K7 | Sennheiser HD650 + Beyerdynamic FOX Mic
Power Supply Seasonic Prime Ultra Platinum 850
Mouse Razer Viper v2 Pro
Keyboard Razer Huntsman Tournament Edition
Software Windows 11 Pro 64-Bit
Thats high IMO even with your cooler. Is the heatsink applied correctly including TIM plus where is the rad. Take a photo.

His temps aren't that high. My friend ran a 3930k around those speeds with little higher voltage I think with an H80 with the similar temps. Right around 80 which is okay. OP what you could do is get faster fans with higher static pressure, since that 120 radiator is probably getting VERY saturated. Or upgrade to something like the H100i or H110 if you are that concerned with temps.

His temperatures will never really hit the temps that he gets in Prime95, during normal usage, in gaming or whatever other usages. SO I think he is okay, but temps could be improved for sure.
 

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
Thats high IMO even with your cooler. Is the heatsink applied correctly including TIM plus where is the rad. Take a photo.

I would like to think they applied it correctly. They used the thermal compound that was already applied to the heatsink. Fans are at the top of the case.

 

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
His temps aren't that high. My friend ran a 3930k around those speeds with little higher voltage I think with an H80 with the similar temps. Right around 80 which is okay. OP what you could do is get faster fans with higher static pressure, since that 120 radiator is probably getting VERY saturated. Or upgrade to something like the H100i or H110 if you are that concerned with temps.

His temperatures will never really hit the temps that he gets in Prime95, during normal usage, in gaming or whatever other usages. SO I think he is okay, but temps could be improved for sure.

An H100 size cooler won't fit in this case unfortunately. Better fans seem like an easy fix if it will yield some improvement, but I'd like to stay somewhat quiet, which the system currently is. Would you recommend fixed rpm fans like I currently have, or something I can control with the MB or speedfan?
 
Joined
Dec 31, 2009
Messages
19,366 (3.73/day)
Benchmark Scores Faster than yours... I'd bet on it. :)
For sure something that is controllable. Though I can't imagine a huge improvement either if you are already running a push pull setup...

TJMax is 91C iirc, so anything under that is good. The further away the better and to shoot for 80C is fine. I wouldnt go over the 86C you have while stress testing, that is for sure. That said, and was already said above, stress testing with P95 usually yields ~10C higher temps than any other non stress testing application.
 
Joined
May 14, 2009
Messages
2,132 (0.39/day)
Location
Chicago burbs
System Name Halloween Boo!
Processor Intel Core i7 3770K
Motherboard Gigabyte Z77-Up7
Cooling Custom Water/ Thermalchill TA 120.3/ Swiftech Apogeee XT/ MCP655/ Swiftech M icrores/ XSPC RX 240
Memory 16G G.Skill trident 2400MHz
Video Card(s) 3 x Radeon 7970
Storage OCZ Revo Drive 240G
Display(s) 24 inch Viewsonic
Case Phobia WayCoolIt Test Bench
Power Supply Nexus 1100 watt
For sure something that is controllable. Though I can't imagine a huge improvement either if you are already running a push pull setup...

TJMax is 91C iirc, so anything under that is good. The further away the better and to shoot for 80C is fine. I wouldnt go over the 86C you have while stress testing, that is for sure. That said, and was already said above, stress testing with P95 usually yields ~10C higher temps than any other non stress testing application.

TJ is measured at center of chip which is immeasureable. Actual readings are about 10 degrees cooler with the sensors thus the 80 degrees. DO NOT TAKE IT ABOVE 80 OR YOU MAY SEE DEGRDATION. It has happened to many. Better to be safe on a chip that costs over $500
 
Joined
Dec 31, 2009
Messages
19,366 (3.73/day)
Benchmark Scores Faster than yours... I'd bet on it. :)
Well aware how TJmax is measured and subsequent statement(s), and you more or less have it. I had a 3930K for several months and it topped out at around mid 80s when stress testing, and never touched 80 doing everything else. Zero degredation... though better safe than sorry, I agree.

That said, when I did hit 91C in RealtempGT. It did throttle anyway.
 

Rogue666

New Member
Joined
Apr 20, 2009
Messages
8 (0.00/day)
Processor i7-3930k
Motherboard ASUS Rampage IV Extreme
Cooling Asetek 570LC
Memory G. Skill Ripjaws 8GB 1866MHz (x4)
Video Card(s) nVidia GTX 680 (x2) SLI
Storage Crucial M4 512GB SSD
Display(s) Dell U2412M (x3)
Case SilverStone custom
Audio Device(s) Creative SB Zx
Power Supply Silverstone Strider Gold 1200W
Software Win 7 64-bit
Thanks for all the input guys. Gave me a little piece of mind, since I doubt I'll go over 80'C while running something other than prime95.

I'm leaning towards trying out a better pair of fans to see if I can get a slightly larger buffer.
 

cadaveca

My name is Dave
Joined
Apr 10, 2006
Messages
17,232 (2.63/day)
Thanks for all the input guys. Gave me a little piece of mind, since I doubt I'll go over 80'C while running something other than prime95.

I'm leaning towards trying out a better pair of fans to see if I can get a slightly larger buffer.

temps are fine, and voltage is low. Intel's turbo is built for throttling, anyway, and these chips are fine running up to the throttle point, just keep voltage within 10% of stock, which by what you've listed, is well within that(mine hits 1.25V at stock).


Next, people will tell you that IVB is 77 W chip, and Haswell is 84W, and Haswell is hotter because it pulls more power.

Sadly, both are 95W chips, TDP refers to cooling needed. IVB needs 77W under normal usage, Haswell needs 84W.


Some aren't aware what "TDP" and "Power Envelope" are to Intel.
 
Joined
Dec 31, 2009
Messages
19,366 (3.73/day)
Benchmark Scores Faster than yours... I'd bet on it. :)
I would be interested to see an official article or so on the 95w value of both gpus. I've never seen that value pinned down before.

You right of course in tdp, but its a fair enough ballpark for most things to estimate power by that...again not assuming utmost accuracy.
 

cadaveca

My name is Dave
Joined
Apr 10, 2006
Messages
17,232 (2.63/day)
I would be interested to see an official article or so on the 95w value of both gpus. I've never seen that value pinned down before.

You right of course in tdp, but its a fair enough ballpark for most things to estimate power by that...again not assuming utmost accuracy.

You can HEAR it out of Intel reps mouth on Newegg videos. SNB, IVB and Haswell are all 95W chips. Also explains the early 95W IVB chips too, eh? Remember that Intel changed the listed number on IVB after reviewer/consumer response, so IVB is MOST DEFINTELY a 95W design.


It's actually explained in decent enough detail to make ya happy with me posting that.;)

[yt]ylNT1Co-Q6k[/yt]

Also mentioned is that the higher TDP on Haswell is due to FIVR, but overall PLATFORM power is down.


Also, Haswell is 154 W MAX. or maybe 158...150-something anyway, and that's listed in the Intel whitepapers.


I'll let the Intel dude explain their reasoning. ;)
 
Joined
Dec 31, 2009
Messages
19,366 (3.73/day)
Benchmark Scores Faster than yours... I'd bet on it. :)
Ick.. mobile and it doesn't show.. will check it out in a min. Thanks!

Edit.. yeah. It would make sense, certainly. Just never heard it pinned down to specific values before. ;)
 
Top