• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Shin Etsu for Nvidia Repaste

Joined
Oct 21, 2005
Messages
6,872 (1.02/day)
Location
USA
System Name Computer of Theseus
Processor Intel i9-12900KS: 50x Pcore multi @ 1.18Vcore (target 1.275V -100mv offset)
Motherboard EVGA Z690 Classified
Cooling Noctua NH-D15S, 2xThermalRight TY-143, 4xNoctua NF-A12x25,3xNF-A12x15, 2xAquacomputer Splitty9Active
Memory G-Skill Trident Z5 (32GB) DDR5-6000 C36 F5-6000J3636F16GX2-TZ5RK
Video Card(s) EVGA Geforce 3060 XC Black Gaming 12GB
Storage 1x Samsung 970 Pro 512GB NVMe (OS), 2x Samsung 970 Evo Plus 2TB (data 1 and 2), ASUS BW-16D1HT
Display(s) Dell S3220DGF 32" 2560x1440 165Hz Primary, Dell P2017H 19.5" 1600x900 Secondary, Ergotron LX arms.
Case Lian Li O11 Air Mini
Audio Device(s) Audiotechnica ATR2100X-USB, El Gato Wave XLR Mic Preamp, ATH M50X Headphones, Behringer 302USB Mixer
Power Supply Super Flower Leadex Platinum SE 1000W 80+ Platinum White
Mouse Zowie EC3-C
Keyboard Vortex Multix 87 Winter TKL (Gateron G Pro Yellow)
Software Win 10 LTSC 21H2
What type of Shin Etsu paste should I use for repasting my GTX 770? I was using Noctua NT-H1 with a thin amount, it worked fine until I bumped the card today while I was rewiring some of the fans. I noticed the temperature greatly rose to where it was performing slightly worse than stock. It wasn't a major problem but I decided I had to repaste it again. Upon removal, I noticed the NT-H1 was still wet even though I applied a week ago. Also it was a very thin amount, it didn't look like enough, even though I was certain to cover the entire die with a thin spread. By this, I mean it looked too viscous. I have gotten better results in the past using a spread rather than the small dot method (that I use for CPUs).


This time I used an unspread glob, hoping to replicate the factory's install. The result was actually better. Idle is now 28*C (stock was 34*C, first repaste was 29*C, after bumping was 31*C) Load temperatures hit only 73*C in 3Dmark11 @ default boost clock of 1254.

I heard that Shin Etsu is the Nvidia reference card's paste. I have seen Shin Etsu G751, X23-7762, and X23-7783D sold in online stores.

This card was a PNY non-reference so the paste was probably a generic.

Which is best for a graphic's card die? Are these non-conductive? What type does Nvidia use?

http://skinneelabs.com/shin-etsu-g751-x23-7762-and-x23-7783d-review/3/

In the above review, G751 looks the closest to every video card I have dissected. It also scores terribly. In other reviews, G751 scores well compared to competition.

Is there something better to use than Shin Etsu for GPUs?
 
Last edited:
Joined
Jun 5, 2013
Messages
80 (0.02/day)
Location
Surabaya, Indonesia
System Name Dragun
Processor i5 4670k
Motherboard MSI z87-GD65
Cooling NZXT Kraken X60
Memory Corsair LP white 2x4GB 1600 Mhz
Video Card(s) Zotac GTX 780
Storage WD Blue 2.5" 5.4K 1 TB + TEAM L3 DARK 240GB
Display(s) AOC i2352vh
Case NZXT Phantom 630
Power Supply NZXT hale82 850M
Keyboard Leopold FC700R
I believe X23-7783D is the highest performing of all and have used a tube back when I liked to tinker with my gaming laptop.
I got about 2-3 C cooler than the stock paste from MSI but it was really hard to apply and I had to warm it to make it soft.
And yes it is non-conductive but I have no idea what NV use for their cards and it really looks like what I used from the light grey colour.
 

MxPhenom 216

ASIC Engineer
Joined
Aug 31, 2010
Messages
12,944 (2.62/day)
Location
Loveland, CO
System Name Ryzen Reflection
Processor AMD Ryzen 9 5900x
Motherboard Gigabyte X570S Aorus Master
Cooling 2x EK PE360 | TechN AM4 AMD Block Black | EK Quantum Vector Trinity GPU Nickel + Plexi
Memory Teamgroup T-Force Xtreem 2x16GB B-Die 3600 @ 14-14-14-28-42-288-2T 1.45v
Video Card(s) Zotac AMP HoloBlack RTX 3080Ti 12G | 950mV 1950Mhz
Storage WD SN850 500GB (OS) | Samsung 980 Pro 1TB (Games_1) | Samsung 970 Evo 1TB (Games_2)
Display(s) Asus XG27AQM 240Hz G-Sync Fast-IPS | Gigabyte M27Q-P 165Hz 1440P IPS | Asus 24" IPS (portrait mode)
Case Lian Li PC-011D XL | Custom cables by Cablemodz
Audio Device(s) FiiO K7 | Sennheiser HD650 + Beyerdynamic FOX Mic
Power Supply Seasonic Prime Ultra Platinum 850
Mouse Razer Viper v2 Pro
Keyboard Razer Huntsman Tournament Edition
Software Windows 11 Pro 64-Bit
Arctic Cooling MX-4
 
Joined
Oct 21, 2005
Messages
6,872 (1.02/day)
Location
USA
System Name Computer of Theseus
Processor Intel i9-12900KS: 50x Pcore multi @ 1.18Vcore (target 1.275V -100mv offset)
Motherboard EVGA Z690 Classified
Cooling Noctua NH-D15S, 2xThermalRight TY-143, 4xNoctua NF-A12x25,3xNF-A12x15, 2xAquacomputer Splitty9Active
Memory G-Skill Trident Z5 (32GB) DDR5-6000 C36 F5-6000J3636F16GX2-TZ5RK
Video Card(s) EVGA Geforce 3060 XC Black Gaming 12GB
Storage 1x Samsung 970 Pro 512GB NVMe (OS), 2x Samsung 970 Evo Plus 2TB (data 1 and 2), ASUS BW-16D1HT
Display(s) Dell S3220DGF 32" 2560x1440 165Hz Primary, Dell P2017H 19.5" 1600x900 Secondary, Ergotron LX arms.
Case Lian Li O11 Air Mini
Audio Device(s) Audiotechnica ATR2100X-USB, El Gato Wave XLR Mic Preamp, ATH M50X Headphones, Behringer 302USB Mixer
Power Supply Super Flower Leadex Platinum SE 1000W 80+ Platinum White
Mouse Zowie EC3-C
Keyboard Vortex Multix 87 Winter TKL (Gateron G Pro Yellow)
Software Win 10 LTSC 21H2
Does MX-4 have less "pump-out" issues than this NT-H1? I am getting good temps with NT-H1 but I am concerned that the slightest shift in the card will unseat the paste. Thats why I figured using a paste similar to the factory paste would be ideal.

There are only 4 screws holding the fan, and the fan's 4 threaded retention posts don't fit into the corresponding holes on the circuit board, it sits above it, so there's a bit of float in its design.
 
Joined
Mar 26, 2010
Messages
9,762 (1.91/day)
Location
Jakarta, Indonesia
System Name micropage7
Processor Intel Xeon X3470
Motherboard Gigabyte Technology Co. Ltd. P55A-UD3R (Socket 1156)
Cooling Enermax ETS-T40F
Memory Samsung 8.00GB Dual-Channel DDR3
Video Card(s) NVIDIA Quadro FX 1800
Storage V-GEN03AS18EU120GB, Seagate 2 x 1TB and Seagate 4TB
Display(s) Samsung 21 inch LCD Wide Screen
Case Icute Super 18
Audio Device(s) Auzentech X-Fi Forte
Power Supply Silverstone 600 Watt
Mouse Logitech G502
Keyboard Sades Excalibur + Taihao keycaps
Software Win 7 64-bit
Benchmark Scores Classified
mx 4 is good
but you need to leave it alittle since thermal paste need time before it reachs its optimal heat transfer
check your pressure too, how tight your hsf and if you tight it, do it cross from upper right to lower left
 
Joined
Oct 21, 2005
Messages
6,872 (1.02/day)
Location
USA
System Name Computer of Theseus
Processor Intel i9-12900KS: 50x Pcore multi @ 1.18Vcore (target 1.275V -100mv offset)
Motherboard EVGA Z690 Classified
Cooling Noctua NH-D15S, 2xThermalRight TY-143, 4xNoctua NF-A12x25,3xNF-A12x15, 2xAquacomputer Splitty9Active
Memory G-Skill Trident Z5 (32GB) DDR5-6000 C36 F5-6000J3636F16GX2-TZ5RK
Video Card(s) EVGA Geforce 3060 XC Black Gaming 12GB
Storage 1x Samsung 970 Pro 512GB NVMe (OS), 2x Samsung 970 Evo Plus 2TB (data 1 and 2), ASUS BW-16D1HT
Display(s) Dell S3220DGF 32" 2560x1440 165Hz Primary, Dell P2017H 19.5" 1600x900 Secondary, Ergotron LX arms.
Case Lian Li O11 Air Mini
Audio Device(s) Audiotechnica ATR2100X-USB, El Gato Wave XLR Mic Preamp, ATH M50X Headphones, Behringer 302USB Mixer
Power Supply Super Flower Leadex Platinum SE 1000W 80+ Platinum White
Mouse Zowie EC3-C
Keyboard Vortex Multix 87 Winter TKL (Gateron G Pro Yellow)
Software Win 10 LTSC 21H2
mx 4 is good
but you need to leave it alittle since thermal paste need time before it reachs its optimal heat transfer
check your pressure too, how tight your hsf and if you tight it, do it cross from upper right to lower left
Yes its tight but not over tight. I have done many GPUs, this one has one of the worst retention schemes.
 

MxPhenom 216

ASIC Engineer
Joined
Aug 31, 2010
Messages
12,944 (2.62/day)
Location
Loveland, CO
System Name Ryzen Reflection
Processor AMD Ryzen 9 5900x
Motherboard Gigabyte X570S Aorus Master
Cooling 2x EK PE360 | TechN AM4 AMD Block Black | EK Quantum Vector Trinity GPU Nickel + Plexi
Memory Teamgroup T-Force Xtreem 2x16GB B-Die 3600 @ 14-14-14-28-42-288-2T 1.45v
Video Card(s) Zotac AMP HoloBlack RTX 3080Ti 12G | 950mV 1950Mhz
Storage WD SN850 500GB (OS) | Samsung 980 Pro 1TB (Games_1) | Samsung 970 Evo 1TB (Games_2)
Display(s) Asus XG27AQM 240Hz G-Sync Fast-IPS | Gigabyte M27Q-P 165Hz 1440P IPS | Asus 24" IPS (portrait mode)
Case Lian Li PC-011D XL | Custom cables by Cablemodz
Audio Device(s) FiiO K7 | Sennheiser HD650 + Beyerdynamic FOX Mic
Power Supply Seasonic Prime Ultra Platinum 850
Mouse Razer Viper v2 Pro
Keyboard Razer Huntsman Tournament Edition
Software Windows 11 Pro 64-Bit
Yes its tight but not over tight. I have done many GPUs, this one has one of the worst retention schemes.

Which 770 is it?

EDIT: Oh PNY? Wierd, a small bump to the gpu shouldnt move the heat sink if its properly mounted.
 
Joined
Oct 21, 2005
Messages
6,872 (1.02/day)
Location
USA
System Name Computer of Theseus
Processor Intel i9-12900KS: 50x Pcore multi @ 1.18Vcore (target 1.275V -100mv offset)
Motherboard EVGA Z690 Classified
Cooling Noctua NH-D15S, 2xThermalRight TY-143, 4xNoctua NF-A12x25,3xNF-A12x15, 2xAquacomputer Splitty9Active
Memory G-Skill Trident Z5 (32GB) DDR5-6000 C36 F5-6000J3636F16GX2-TZ5RK
Video Card(s) EVGA Geforce 3060 XC Black Gaming 12GB
Storage 1x Samsung 970 Pro 512GB NVMe (OS), 2x Samsung 970 Evo Plus 2TB (data 1 and 2), ASUS BW-16D1HT
Display(s) Dell S3220DGF 32" 2560x1440 165Hz Primary, Dell P2017H 19.5" 1600x900 Secondary, Ergotron LX arms.
Case Lian Li O11 Air Mini
Audio Device(s) Audiotechnica ATR2100X-USB, El Gato Wave XLR Mic Preamp, ATH M50X Headphones, Behringer 302USB Mixer
Power Supply Super Flower Leadex Platinum SE 1000W 80+ Platinum White
Mouse Zowie EC3-C
Keyboard Vortex Multix 87 Winter TKL (Gateron G Pro Yellow)
Software Win 10 LTSC 21H2
As I said, its impossible to properly mount, the standoffs for the heatsink don't actually go through the holes in the pcb, they sort of rest on the edge of the hole. Therefore when you screw it in, it can wobble.
 
Top