Recent content by Captn Chuck

yes i have tried every cable it came with and the drivers and the newest drivers . I have also forced detection on my tv and that still did nt help . Its funny every other card i have had has been an ati card and have been able to run tv for dvd veiwing but this one . I have got an RMA number...

I have tried every cable sent with the box and all known drivers. I play my dvds on my tv and have had no problems in the past with other ATI cards but this one . Can anyone help. Do I need to return it and get a new one I just got it . I can run dual displays with monitors but can run one...

Yes I have downloaded one from the bios center here , but dont know which flashing tool to use . Im not sure if I downloaded the right bios , there was only one for the sapphire X1800XT-PE . Thanks for the feed back . Also Im alittle leary to flash the card , I paid 319.99 for it . So I want to...

my card is a 512 mb 256 bit and stock in ati tool is 600 700. my 4 gig of ram on my mobo are xms 3200 running a 3-3-3-8. dose this help , I would like to get this thing running at pe speeds wioth out over clocking , I would rather flash the bios . I have done a vid card before a long time agoe a...

Aowe my god This movie hits home . I have been ever where these guys have been , I laughed my ass off .:roll:

I cant seem to get ati tool to run on this mobo , I have an X800gto by sapphire in the machine , I use to have it in a nother and i could over clock it to 510-560 and ran great . This mobo Has an ATI chipset and onboard graphics . I dont know if this has anything to do with my problem ,,,, any...

The card I m getting is the X1800XT 512 256. My system I'm running is a AMD 64 X2 3800 , which is oc'ed to 2.5 , I have 4 gigs of XMS 3200 ram and a XFI extreme sound card . I will have the card thursday . I hope this is what you ment about ram .

Im getting A Sapphire X1800XT on thursday and would like to know what to look for on the chip set so I know I can flash it to a X1800XT PE , my last card is a X800 GTO and was not able to unlock the other four pipes because of the set up on the chip . Any help would be great . Thank you .

I did send the fuse data to petao1 and i hope it will help . How do i take a pic of the fus data and post it

Dose any one know a good running temp for video cards , I have mine over clocked from 400-490 to 523 -558 and its running around 60 for GPU and 55 on temp chip . My fan is runn at 54% .Is this a safe range to run the temps at ? Hope some one can help . My bench mark 05 went from 4448 to 5443...

Dose anyone know if the other four pipes can be opened on this crd the card has a R480 chip and a huge heat sink and fan . If anyone can help that would be great .If you need anyother info just ask if it will help.The card has 256 256 on it . Stock ram is 400-980 . My card is PCIe not AGP.

Dose anyone have this card and can someone tell me if it would be better than the connect3d version.I'm upgrading my system and Im have problems figuring what card to get .I know the connect3d card can be flashed to open the other four pipes .Dose anyone know if the same can be done with the...

I have a question about over clocking , is it better to lower the multiplyer and raise the front side. Right know I have mine at 15 X 167 which gives me 2505 and my volts are at 1.86.Should I set the multi down to 12.5 and the the front side up to 200 . Right now I idle around 50-52 c . I have a...

Fuzzy logic is a MSI tool for overclocking from MSI . I flashed my bios, It finally say its a mobil 2600+. What do you have your multplyer at and front side bus ? Maybe at 15 times is to high for this chip on this board . I really considering getting a abit . I built my girl friends computer...

Just downloaded the cup-z and it says my multiplyer is at 15 x 145.5, but in my cmos it is set a 12.5/13 x 145. What is with that? Any thoughts ? Plus when looking at the fuzzy logic the front side bus is diffrent then in my cmos.