Recent content by leo 10

i m using everything on auto except for dram volt 1.35, soc volt 1.1, xmp profile 1 (3600) and the others timing settings for the ram suggested by@ tabascosauz this is ryzen master and zentimings screenshot i also set ryzen balanced power management now i m running memtest64 and prime95...

unbelivable mine during bmw test is stuck at 4.00 ghz with all cores finishing in 1min 56 sec (done right now with bios on default and only dram 1.35) your in bmw test is going at 4.20 ghz with all cores finishing in 2min 21 sec on blender official page our cpu shuold use 100 sec to finish...

hardware info or now i got ryzen mester or openhardware i think is called today i ll try cpuz but everyone reports the same speed at the end i compare render time and there i see 20-25 more sec 120 of my 3900x against 100 of official blender page... and the speed during render stays fixed for...

prime95 with ram at 3200, ratio 4.25 ghz, 1.30 vcore, 1.35 dram voltage crashes after 40 min now i restore default and set only v core to 1.25 and dram to 1.35 render time slow, 4.00ghz prime95 crash again after about 40 min what do you mean with cpu speed and temps under control? and...

when i finished building my pc i got crash with reboot while rendering caused by ram so i set dram voltage to 1.35 and it fixed it, than i set 3200 at ram speed and it is still ok but when i set 3600 with no other changes it crash i don t want to mess around with anything of bios setting but...

f4-3600c16d-32gtznc cl 16-19-19-39 1.35v i think that mine are these https://www.gskill.com/product/165/326/1562840211/F4-3600C16D-32GTZNCTrident-Z-NeoDDR4-3600MHz-CL16-19-19-39-1.35V32GB-(2x16GB)

ok if others specs of my ram are needed to understand the right settings i ll give to you but you have to specify what you want to know about my ram yesterday i tested with tabascosauz ram settings but before i laoded defaults in bios...and it worked (render times are again very high) then i...

i have found it!!

ok for now pc doesn t crash while render but cpu stay under 4.00 ghz and render time is high now i try cpu ratio 4.30 and cpu vcore 1.31 still can t find how to disable power down mode... now with these new settings cpu ratio 4.30 and cpu vcore 1.31 crash under load trying 4.20 and 1.298

i didn t check but i have a Mobo : x570 aorus elite and ram are 2 ddr4 tridentz neo 3600 16gb are they incompatible with each other? i found on this page...

manual soc to 1.1 you mean vcore soc?? inside advanced timing control i don t have tCl value i have tCWL , is that one?? or tcl is cas latency? i found all the other these are my two doubt.. yes i was asking that because of the vcore and cpu ratio changes 4.3 ghz and 1.31 V i m using this for a...

i didn t check but i have a Mobo : x570 aorus elite and ram are 2 ddr4 tridentz neo 3600 16gb are they incompatible with each other? i found on this page https://pangoly.com/it/recensione/gigabyte-x570-aorus-elite/compatibilita/memoria-ram that my ram is compatible with my mobo ok i ll try...

my temp under load are around 80°, isn t that good? i was thinking that i have to find out by myself the right timings...but now i understand that i can copy yours, is that right?? no i only change dram voltage to 1.35

so i still don t know if cpu clock ratio 4.3 and cpu vcore at 1.31 are safe settings and if there are other change to be made?? the core boost to 4.5-4.6 ghz for really short time so i don t think that loosing single core performance is really a big deal but with these setup render time...