what do you recommend for 2000mhz ram

[kopekbaligi]

Just as you can see below, my RAMs is working on 1684 for now and When I have pushed them 2000MHz, PC just hangs on a black screen at the BIOS boot so I understand they require a bit more voltage. But DRAM bus voltage is enough in my opinion. To What should I give more voltage and how much voltage should I give?

Ai Overclock Tuner - Manual
CPU Ratio Setting - 19
Intel (R) SpeedStep (TM) Tech - Disabled
Intel (R) Turbo Mode Tech - Disabled
BCLK Frequency - 211
PCIE Fequency - 100
DRAM Frequency - DDR3 - 1688MHz

DRAM CAS# Latency - 9 DRAM Clock
DRAM RAS# to CAS# Delay - 9 DRAM Clock
DRAM RAS# PRE Time - 9 DRAM Clock
DRAM RAS# ACT Time - 24 DRAM Clock

(2nd formation: 2T)

CPU Voltage 1.300v
CPU PLL Voltage - Auto
QPI/DRAM Core Voltage - 1.3250v
IOH Voltage - 1.10v
IOH PCIE Voltage - Auto
ICH Voltage - Auto
ICH Voltage - Auto

DRAM Bus Voltage - 1.64v
DRAM DATA REF Voltage on CHA - Auto
DRAM CTRL REF Voltage on CHA - Auto
DRAM DATA REF Voltage on CHB - Auto
DRAM CTRL REF Voltage on CHB - Auto
DRAM DATA REF Voltage on CHC - Auto
DRAM CTRL REF Voltage on CHC - Auto

Load-Line Calibration - Enabled
CPU Differential Amplitude - Auto
CPU Clock Skew - Auto
CPU Spread Spectrum - Enabled
IOH Clock Skew - Auto
PCIE Spread Spectrum - Enabled

 

[Athlon2K15]

i dont even know what chip your overclocking here? im assuming its a i7 920? if so why you using a 19 multi?

 

[kopekbaligi]

sorry, silly me
ASUS P6T SE X58 Socket
Intel Core i7 920 d0
Thermalright Ultra 120 eXtreme Rev C
TEAM Xtreem LV (3*2) 6GB 2000mhz 9-9-9-24-2T
Sapphire HD5870 GDDR5 1GB 256Bit
Seagate 1TB 7200RPM SATA-II 32MB NCQ
Thermaltake Toughpower 750W

 

[[crs]]

Give G.Skill a look, ive got the 2000MHz 4gb kit (x2) for the socket 1156 and it is running a dream with the XMP profile. Not sure if they do tri channel kits tho

 

[overclocking101]

yeah was gonna say 1366 chip 1156ers dont have qpi volts. try running them with a different divider and higher/lower bclk and see what happens. Also you will; need at least 1.65V I usually set mine to 1.66v that little bit can make a difference. Also is there a performance level setting in the bios?? List EVERY bios setting that has to do with ram. maybe you need to raise QPI volts?? try 1.35 or a tad higher. change it from 2T to 1T also.

Give G.Skill a look, ive got the 2000MHz 4gb kit (x2) for the socket 1156 and it is running a dream with the XMP profile. Not sure if they do tri channel kits tho

Also buying new ram is not necessary. those Team Xtreems he is using are using elpida hypers which are better than the G.skill elpida bbse's you reccomended. what the problem more than likely is is that his kit isnt on that motherboards QVL and whith ASUS QVL is like the bibble. there boards usually run non qvl ram like crap.

do you have the latest/newest bios m8??