asus rampage v adventures

msimax · Mar 16, 2015

EarthDog said:
Interesting that this bios doesn't use the 125 strap to reach 3200Mhz memory....

yes this bios bios is more forgiving of samsung ram and i am about to test 1302 to see improvements if any

msimax · Mar 22, 2015

been trying my damnest to get my read speeds into the 70gb area mems are the corsair 2800 lpx and has samsung chips.
really dont need or want to upgrade but I see what ppl getting on hynix and see kit prices drop but i been tuning the hell out this kit lol

so super virgin tight imma need a miracle lol , cant lower trcd and trp at this speed. ill guess im good for this daily and it looks like ddr4 dried up on newegg

got some case bling also serves as flashlight cause i'm always poking around going to clean out dust bunnies and add new fittings today

petedread · Apr 7, 2015

Got my rig watercooled now and it's opened up a lot more scope for overclocking. I can now use more than 1.250vcore. I've got water blocks on the vrm and pch too. Doubt they will make much difference though. Looks like I have the same GPU block as you. I have the active back plate, it looks great and realy helps cool the gpu vrm1 even further BUT with the back plate I can not install my gpu in to PCI slot 1. The back plate hits the bottom of the ram slots.

EarthDog · Apr 7, 2015

That won't make a bit of difference outside of restricting your loop a bit (cooling power bits/PCH).

petedread · Apr 8, 2015

^^ yeah I realise that cooling those components is not going to help me get higher clocks, especially with my set up and this particular CPU, but it looks good lol.

jaggerwild · Apr 8, 2015

why are you over clocking with four stick of memory? at 4500 that board will auto volt, you may need to drop the voltage a bit but you'd be good.

msimax · Apr 11, 2015

petedread said:
Got my rig watercooled now and it's opened up a lot more scope for overclocking. I can now use more than 1.250vcore. I've got water blocks on the vrm and pch too. Doubt they will make much difference though. Looks like I have the same GPU block as you. I have the active back plate, it looks great and realy helps cool the gpu vrm1 even further BUT with the back plate I can not install my gpu in to PCI slot 1. The back plate hits the bottom of the ram slots.

yea i was planning on getting those back plates but didnt think they would be compatible with sli/cf wb bridge

EarthDog said:
That won't make a bit of difference outside of restricting your loop a bit (cooling power bits/PCH).

actually the vrm cooler makes sense because they do get hot with reported temps in the 80c range when overclocking heavy and asus reps recommending placing a fan over it

jaggerwild said:
why are you over clocking with four stick of memory? at 4500 that board will auto volt, you may need to drop the voltage a bit but you'd be good.

the x99 platform needs 4 sticks of memory to enable quad channel. and i dont worry about auto volts i apply all my torture manually lol

msimax · Apr 11, 2015

jaggerwild · Apr 11, 2015

LOL!
You know it all, nice rats nest very impressive :fear:

msimax · Apr 12, 2015

LOL im always inside of it fiddling around now im playing with some crucials

jaggerwild · Apr 12, 2015

Here ya go, 2 GPU'S almost beat yer score. CRANK IT UP!
http://hwbot.org/submission/2527229...performance_2x_geforce_gtx_780_ti_72407_marks

msimax · Apr 12, 2015

jaggerwild said:
Here ya go, 2 GPU'S almost beat yer score. CRANK IT UP!
http://hwbot.org/submission/2527229...performance_2x_geforce_gtx_780_ti_72407_marks

that score using .700+ ghz and single stage this is just my daily driver on water he's catching up

msimax · Apr 12, 2015

lower cpu omega drivers and more gpu clocks

jaggerwild · Apr 12, 2015

At least they are fixing there drivers, tests like 3Dmark 05 with 3 way SLI used to go backwards. I could do 5400 with water on that system, sadly the board died in flames................

msimax · Apr 12, 2015

i have that same issue with cf in 03 single card scores the highest guess i need more horse power when running all 3 cards

msimax · Apr 12, 2015

so i been up trying to achieve the impossible 3000mhz with micron on RVE lol

petedread · Apr 12, 2015

Yeah the back plate mite not work for you. I think EK do a back plate that you could use.

The mobo VRM stays very cool now under load. Running Asus real bench the VRM hits about 40c with a 4.4 1.3v oc. And thats with only having one 360 rad and a GPU in the loop. I have the switching rate set to 700.

msimax · Apr 12, 2015

msimax · Apr 12, 2015

petedread said:
Yeah the back plate mite not work for you. I think EK do a back plate that you could use.

The mobo VRM stays very cool now under load. Running Asus real bench the VRM hits about 40c with a 4.4 1.3v oc. And thats with only having one 360 rad and a GPU in the loop. I have the switching rate set to 700.

does the ek back plate actively cool or just for show?

msimax · Apr 13, 2015

cas 11 or bust :coffee::comp10:

Vlada011 · Apr 13, 2015

WOW that's one incredible memory kit.
So low latency on such speed, even for 2800MHz kit that would be amazing results.
I like them immediately when Crucial show them, and Mushkin Black Frostbyte are nice but I choose this time something tested on R5E, GSkill 2800.
They are cheap, 215e and tested by ASUS.
They can't say it's not compatible you should choose QVL kit.

Mydog · Apr 13, 2015

Very nice memory OC'ing, could you elaborate on what voltages you're using? Maybe post a screen with TurboV

Vlada011 · Apr 13, 2015

I just want to ask that, probably is 1.35V.
It's not often some kit to over pass 2 levels over specification with much tighter latency.
This is extremely low latency and for 2666MHz.

Mydog · Apr 13, 2015

Vlada011 said:
I just want to ask that, probably is 1.35V.
It's not often some kit to over pass 2 levels over specification with much tighter latency.
This is extremely low latency and for 2666MHz.

I agree but my guess is well over 1.4 vmem and maybe some increase on other things.

msimax · Apr 13, 2015

Mydog said:
Very nice memory OC'ing, could you elaborate on what voltages you're using? Maybe post a screen with TurboV

Vlada011 said:
I just want to ask that, probably is 1.35V.
It's not often some kit to over pass 2 levels over specification with much tighter latency.
This is extremely low latency and for 2666MHz.

i choose this kit because not to many ppl are using them atm and i wanted to bench something different, being that booting 3000 on rve is lucky i feel

this is balls to the wall but my cas12 is around 1.45

System Name	2020 build
Processor	3950x
Motherboard	Gigabyte Aorus extreme
Cooling	Custom Loop. PETG. Phanteks 140 distro plate. EK 400mm res. EK GPU/back plate. EK CPU.480rad 2x360
Memory	32gig 3600mhz 16,16,16,36. Trident Z Royal
Video Card(s)	MSI gaming X trio 2080ti
Storage	2TB Gigabyte Aorus gen4. 1TB Aorus gen4
Display(s)	LG CX 55
Case	Phanteks 719
Audio Device(s)	Audeez LCD3. Chord Hugo 2
Power Supply	Seasonic prime 1300 platinum
Software	Cubase, Adobe

System Name	2020 build
Processor	3950x
Motherboard	Gigabyte Aorus extreme
Cooling	Custom Loop. PETG. Phanteks 140 distro plate. EK 400mm res. EK GPU/back plate. EK CPU.480rad 2x360
Memory	32gig 3600mhz 16,16,16,36. Trident Z Royal
Video Card(s)	MSI gaming X trio 2080ti
Storage	2TB Gigabyte Aorus gen4. 1TB Aorus gen4
Display(s)	LG CX 55
Case	Phanteks 719
Audio Device(s)	Audeez LCD3. Chord Hugo 2
Power Supply	Seasonic prime 1300 platinum
Software	Cubase, Adobe

Processor	5930K
Motherboard	MSI X99 SLI
Cooling	WATER
Memory	16GB DDR4 2132
Video Card(s)	EVGAY 2070 SUPER
Storage	SEVERAL SSD"S
Display(s)	Catleap/Yamakasi 2560X1440
Case	D Frame MINI drilled out
Audio Device(s)	onboard
Power Supply	Corsair TX750
Mouse	DEATH ADDER
Keyboard	Razer Black Widow Tournament
Software	W10HB
Benchmark Scores	PhIlLyChEeSeStEaK

Processor	5930K
Motherboard	MSI X99 SLI
Cooling	WATER
Memory	16GB DDR4 2132
Video Card(s)	EVGAY 2070 SUPER
Storage	SEVERAL SSD"S
Display(s)	Catleap/Yamakasi 2560X1440
Case	D Frame MINI drilled out
Audio Device(s)	onboard
Power Supply	Corsair TX750
Mouse	DEATH ADDER
Keyboard	Razer Black Widow Tournament
Software	W10HB
Benchmark Scores	PhIlLyChEeSeStEaK

Processor	5930K
Motherboard	MSI X99 SLI
Cooling	WATER
Memory	16GB DDR4 2132
Video Card(s)	EVGAY 2070 SUPER
Storage	SEVERAL SSD"S
Display(s)	Catleap/Yamakasi 2560X1440
Case	D Frame MINI drilled out
Audio Device(s)	onboard
Power Supply	Corsair TX750
Mouse	DEATH ADDER
Keyboard	Razer Black Widow Tournament
Software	W10HB
Benchmark Scores	PhIlLyChEeSeStEaK

System Name	Intel® X99 Wellsburg
Processor	Intel® Core™ i7-5820K - 4.5GHz
Motherboard	ASUS Rampage V E10 (1801)
Cooling	EK RGB Monoblock + EK XRES D5 Revo Glass PWM
Memory	CMD16GX4M4A2666C15
Video Card(s)	ASUS GTX1080Ti Poseidon
Storage	Samsung 970 EVO PLUS 1TB /850 EVO 1TB / WD Black 2TB
Display(s)	Samsung P2450H
Case	Lian Li PC-O11 WXC
Audio Device(s)	CREATIVE Sound Blaster ZxR
Power Supply	EVGA 1200 P2 Platinum
Mouse	Logitech G900 / SS QCK
Keyboard	Deck 87 Francium Pro
Software	Windows 10 Pro x64

System Name	Gamer - Bencher
Processor	i7 5960X @5.1 GHz - load temps -5 C
Motherboard	Rampage V Extreme
Cooling	LD PC-V2 Phase Change - White XL Suction
Memory	16GB G.Skill Ripjaws 4 3200 MHz CL14-14-15-25 1t
Video Card(s)	Titan X SLI
Storage	2x 180GB Intel 330
Display(s)	Asus Swift PG278Q G-Sync
Case	Lian Li PC343B-XT
Audio Device(s)	Onboard
Power Supply	Antec 1200W TPQ + Corsair AX1200i
Software	Win 7 64 bits + Win 8.1 64 bit