Ok guys help.
I'we bought brand new components
MSI krait gaming z370
Psu corsair rm650x
I7 8700
2x 8gm gskill trident z 3000mhz
1070ti gtx
When I went to put parts together pc didnt post...I put ram in 3 and 4 slot...pc boots but tells me to put ram in dimm 2 for optimum performance.
Since I've had simmilar problem before I lifted cpu and saw a bend pin. Since I've ordered parts from store 500km from me, I decide to try to unbind it myself. Didn't work, so I take it to local store where he said that he can try to unbind it but it may broke it also. I told him to try, and bind broke. Since he also repairs mobile phones etc. He solders pretty good under microscope with some micro powder or something like that...something really small
After seeing his work those pins look pretty good.
We put cpu use HIS psu pc boots with ram in dimm slot 2.
I got home put mbo in case...put cooler...nothing..no signal at all.
Tomorrow I take it again to him he check under microscope and clean a bit etc. We put cpu and HIS psu...all ok...bios appears.
I get home try all again...nothing no sign.
I go to him we use HIS psu start cpu all ok...this time I check my brand new corsair rm650x psu and it turn out to be dead.
I borrow his psu take it home, mbo lights up and light down...light up...lights dow...vent on psu starts to spin and than stops, spins and stops...
I've tryed 2 diffrent power socket im my house...so that ok.
Now I wonder, could it be that binds are touching eachother and that kills psu?
But if this is possible how did cpu survive?
Anyone got some suggestions?
I've contact msi directly and they were very friendly...they told me to RMA it trought my seller, but the thing is that my seller isn't half friendly as msi guys are. They told me that I touched bind and warranty is void.
I'll send you pictures of binds, that bind is not normaly bend..its curly...so its almost impossible for me to bend it like that. As soon my guy try to unbend it broke, so If I bend it like that (in a curly position) than I must be some kind of genious.
Also I don't get i how once cpu works normaly but after 1h it can't boot at all.
Pictures below shows curly pin and pin after he solder it.
Pls help.
P.S.
Sorry for my english...+ im on my phone
I'we bought brand new components
MSI krait gaming z370
Psu corsair rm650x
I7 8700
2x 8gm gskill trident z 3000mhz
1070ti gtx
When I went to put parts together pc didnt post...I put ram in 3 and 4 slot...pc boots but tells me to put ram in dimm 2 for optimum performance.
Since I've had simmilar problem before I lifted cpu and saw a bend pin. Since I've ordered parts from store 500km from me, I decide to try to unbind it myself. Didn't work, so I take it to local store where he said that he can try to unbind it but it may broke it also. I told him to try, and bind broke. Since he also repairs mobile phones etc. He solders pretty good under microscope with some micro powder or something like that...something really small
After seeing his work those pins look pretty good.
We put cpu use HIS psu pc boots with ram in dimm slot 2.
I got home put mbo in case...put cooler...nothing..no signal at all.
Tomorrow I take it again to him he check under microscope and clean a bit etc. We put cpu and HIS psu...all ok...bios appears.
I get home try all again...nothing no sign.
I go to him we use HIS psu start cpu all ok...this time I check my brand new corsair rm650x psu and it turn out to be dead.
I borrow his psu take it home, mbo lights up and light down...light up...lights dow...vent on psu starts to spin and than stops, spins and stops...
I've tryed 2 diffrent power socket im my house...so that ok.
Now I wonder, could it be that binds are touching eachother and that kills psu?
But if this is possible how did cpu survive?
Anyone got some suggestions?
I've contact msi directly and they were very friendly...they told me to RMA it trought my seller, but the thing is that my seller isn't half friendly as msi guys are. They told me that I touched bind and warranty is void.
I'll send you pictures of binds, that bind is not normaly bend..its curly...so its almost impossible for me to bend it like that. As soon my guy try to unbend it broke, so If I bend it like that (in a curly position) than I must be some kind of genious.
Also I don't get i how once cpu works normaly but after 1h it can't boot at all.
Pictures below shows curly pin and pin after he solder it.
Pls help.
P.S.
Sorry for my english...+ im on my phone