• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

pinmods for socket 478?

Joined
Feb 12, 2007
Messages
1,192 (0.24/day)
Location
scotland
System Name spuds K8-X2
Processor amd athlon X2 4200+ toledo s939 2794mhz 254x11 1.4 vcore
Motherboard MSI K8N Neo4-F v1.0 (MS-7125) nforce4 sata2 mod, laptop cpu heatpipe copper nb cooler
Cooling akasa evo "blue" + 90mm fan, 2x120mm front, 250mm side, 120mm rear, 120mm in psu, pci slot exhaust.
Memory OCZ Platinum XTC DDR PC3200 4GB(4x1024) @254mhz 3-3-3-8 2T
Video Card(s) sapphire HD3870 512mb GDDR4 vf900cu, several ramsinks on components / nvidia 7300gt 256mb secondary
Storage hitachi 160gb (slightly fried) / hitachi 120gb ATA / Seagate 160gb / 2x ps3 seagate 60gb
Display(s) CTX EX1300F 20" flat CRT, 1280x1024@100hz / 19" benq FP91G X / 19" hanns-g (all free)
Case mesh server/gaming black case, 9x 5.25' drive bays, silvestone auto fan controller
Audio Device(s) onboard realtek alc850 7.1/soundblaster LIVE! ct4780 + kxaudio - sony home theatre surround
Power Supply winpower 650w, system draws around 470-500w under load(+all screens)
Software win7 64bit
Benchmark Scores ~16m trips/sec using mty trip generator. triple monitor gaming using SoftTH. 3840x1024
has anyone done any to there system? been looking around the net and found a few, but the ones i was most intrested in were dead links, and others were conflicting,
apparently i can make my celeron operate at a 133(533)fsb instead of 100(400)fsb, by isolating one of the bsel pins, but what one? dont wanna snap off the wrong one lol,
at the moment iv connected AD6(BSEL[0]) to AD7(VCC), that made it run at 100fsb with the ram running same speed instead of being on a divider, where i read this it said its for 133 fsb, so not too sure if it was meant for this cpu, any help/advice on this much appreciated.
 
Joined
Feb 12, 2007
Messages
1,192 (0.24/day)
Location
scotland
System Name spuds K8-X2
Processor amd athlon X2 4200+ toledo s939 2794mhz 254x11 1.4 vcore
Motherboard MSI K8N Neo4-F v1.0 (MS-7125) nforce4 sata2 mod, laptop cpu heatpipe copper nb cooler
Cooling akasa evo "blue" + 90mm fan, 2x120mm front, 250mm side, 120mm rear, 120mm in psu, pci slot exhaust.
Memory OCZ Platinum XTC DDR PC3200 4GB(4x1024) @254mhz 3-3-3-8 2T
Video Card(s) sapphire HD3870 512mb GDDR4 vf900cu, several ramsinks on components / nvidia 7300gt 256mb secondary
Storage hitachi 160gb (slightly fried) / hitachi 120gb ATA / Seagate 160gb / 2x ps3 seagate 60gb
Display(s) CTX EX1300F 20" flat CRT, 1280x1024@100hz / 19" benq FP91G X / 19" hanns-g (all free)
Case mesh server/gaming black case, 9x 5.25' drive bays, silvestone auto fan controller
Audio Device(s) onboard realtek alc850 7.1/soundblaster LIVE! ct4780 + kxaudio - sony home theatre surround
Power Supply winpower 650w, system draws around 470-500w under load(+all screens)
Software win7 64bit
Benchmark Scores ~16m trips/sec using mty trip generator. triple monitor gaming using SoftTH. 3840x1024
nice one!, i just wasn't sure which pin to isolate, an its that same pc i was flashing the bios on, not my main one lol, heres the results so far using cpufsb,

ill try that pin mod soon, try to find a way of painting it first, try an avoid snapping unless i have to,
 

Namslas90

New Member
Joined
Aug 27, 2006
Messages
4,846 (0.94/day)
Location
Earth
nice one!, i just wasn't sure which pin to isolate, an its that same pc i was flashing the bios on, not my main one lol, heres the results so far using cpufsb,

ill try that pin mod soon, try to find a way of painting it first, try an avoid snapping unless i have to,
That "wire casing" slipcover" is a proven method. :toast:
 
Joined
Feb 12, 2007
Messages
1,192 (0.24/day)
Location
scotland
System Name spuds K8-X2
Processor amd athlon X2 4200+ toledo s939 2794mhz 254x11 1.4 vcore
Motherboard MSI K8N Neo4-F v1.0 (MS-7125) nforce4 sata2 mod, laptop cpu heatpipe copper nb cooler
Cooling akasa evo "blue" + 90mm fan, 2x120mm front, 250mm side, 120mm rear, 120mm in psu, pci slot exhaust.
Memory OCZ Platinum XTC DDR PC3200 4GB(4x1024) @254mhz 3-3-3-8 2T
Video Card(s) sapphire HD3870 512mb GDDR4 vf900cu, several ramsinks on components / nvidia 7300gt 256mb secondary
Storage hitachi 160gb (slightly fried) / hitachi 120gb ATA / Seagate 160gb / 2x ps3 seagate 60gb
Display(s) CTX EX1300F 20" flat CRT, 1280x1024@100hz / 19" benq FP91G X / 19" hanns-g (all free)
Case mesh server/gaming black case, 9x 5.25' drive bays, silvestone auto fan controller
Audio Device(s) onboard realtek alc850 7.1/soundblaster LIVE! ct4780 + kxaudio - sony home theatre surround
Power Supply winpower 650w, system draws around 470-500w under load(+all screens)
Software win7 64bit
Benchmark Scores ~16m trips/sec using mty trip generator. triple monitor gaming using SoftTH. 3840x1024
worked a treat!

startup speed without having to use any programs,
its a not a bad mb apart from the lack of oc options, now at least its not gonna be so slow on cnc 3 network games
 
Top