voxhel let me know...are you using the latest bios version?thx tatty i'll see what i can do..
Hello Kiddy!
yes i have the 1402.
here i my specs:
4.233Mhz Boots ok can work (simple jobs) but if i run Prime95 it frezes after 5 secs!
Overclocker Tuner: Manual
CPU Ratio Setting: 8.5
FSB Frequency: 495
PCIE Frequency: 100 (i think this is the only value to go higher as it is! 102 blocks)
FSB Strap To North Bridge: 333
DRAM Frequency: ddr3-1585mhz the 2ª highest
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control: Manual
CAS Latency: 7
DRAM RAS to CAS Delay: 7
DRAM RAS Precharge: 7
DRAM RAS Activate to Precharge: 18
RAS TO RAS Delay: Auto
Row Refresh Cycle Time: AUTO
Write Recovery Time: Auto
Read To Precharge Time: Auto
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled
DRAM Read Training: Disabled
DRAM Write Training: Disabled
MEM OC Charger: ENABLE
Ai Clock Twister: auto
AI Transaction Booster: AUTO
CPU Voltage: 1.45 !!
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): Auto
CPU PLL Voltage: 1.70
FSB Termination Voltage: 1.74
DRAM Voltage: 2.10 !!!
NB Voltage: 1.58 !!!
NB GTL Voltage: Auto
SB Voltage: auto
PCIE SATA Voltage: auto
Load-Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew: AUTO
NB Clock Skew: AUTO
and a run on orthos
orthos report:
Type: Large, in-place FFTs - stress some RAM Min: 128 Max: 1024 InPlace: Yes Mem: 8 Time: 15
CPU: 4207MHz FSB: 497MHz [494MHz x 8.5 est.]
02-10-2008 21:39
Launching 2 threads...
1:Using CPU #0
2:Using CPU #1
1:Beginning a continuous self-test to check your computer.
1
ress Stop to end this test.
2:Beginning a continuous self-test to check your computer.
2
ress Stop to end this test.
1:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.
2:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.
1:FATAL ERROR: Rounding was 0.5, expected less than 0.4
1:Hardware failure detected, consult stress.txt file.
1:Torture Test ran 0 minutes 32 seconds - 1 errors, 0 warnings.
1:Execution halted.
2:Torture Test ran 0 minutes 32 seconds - 0 errors, 0 warnings.
2:Execution halted.
Type: Small FFTs - stress CPU Min: 8 Max: 8 InPlace: Yes Mem: 8 Time: 15
CPU: 4207MHz FSB: 497MHz [494MHz x 8.5 est.]
02-10-2008 21:41
Launching 2 threads...
1:Using CPU #0
2:Using CPU #1
1:Beginning a continuous self-test to check your computer.
1
ress Stop to end this test.
2:Beginning a continuous self-test to check your computer.
2
ress Stop to end this test.
1:Test 1, 800000 Lucas-Lehmer iterations of M172031 using 8K FFT length.
2:Test 1, 800000 Lucas-Lehmer iterations of M172031 using 8K FFT length.
2:FATAL ERROR: Rounding was 0.5, expected less than 0.4
2:Hardware failure detected, consult stress.txt file.
2:Torture Test ran 0 minutes 56 seconds - 1 errors, 0 warnings.
2:Execution halted.
1:Torture Test ran 0 minutes 56 seconds - 0 errors, 0 warnings.
1:Execution halted.
CPU Temps with RealTemp 2.70 ( 27,33,47,47) RealTemp 2.79.8 (32,38,52,52) in witch one do we belive?
if can help please
tks
voxhel