Discussion in 'Cases, Modding & Electronics' started by DaMulta, Jul 7, 2008.
yes i bought it in bundle 3in1 overclocked package
its a little messy but it gets the job done
looks big u dont se case?
i have a stacker 830 but was doing some cable management so i removed everything out of it and decided to do a dice run
i dont have a spare one right now.
Sweet! Let's see some Benchies.
Are you on air?
rig is watercooled check my project log
Yesterday morning i was bored to death and i also had 2 cm fans lying around so i found something to do with them.I added them to my Mushasi.I turned out to be great and a couple of degrees lower!The only bad thing is that i had to hung!! the pdb from the top in order to hold the added weight!
It's mine now...
I had to take the Girl Child's Pink Waterputer away. She was getting out of hand. Momma don't let Poppa spank her butt so instead Poppa's got a Pink Waterputer in lock down.
It's been in a cubby hole in the Girl's desk so I kind of forgot how it looked...that whole period of time was a blur...too many long days and nights.
Awwww! Her puter is gone!!! Well it's a sexy thing non the less!!!
WOW ALL these 4870s and u only score 22k on 06??Or is this with just the one?
Here's my PC that I use, an Acer Aspire AX3200. It's not bad, just limits what you can upgrade and such. I would have taken a picture of the inside, but I haven't changed andthing, so there's not much to see. Also attached are a couple pics of my new gaming build ATM. I had some problems with the built-in fan controller, that's why cables are strung out everywhere. I have a mobo and heatsink, but no CPU, that's why the mobo isn't in it.
Just finished up the loop ....
Radiator right now is the weakest link but it's working ok. No mods done to the case itself.
lookin' good man! now hows the temps? That's what important!!!
What about the rad!?? It's not like your waiting on someone to finish his build are you!?
Actually yes I am waiting **shakes fist**
Temps are fine, linpack load @ 4Ghz is 53-55C. Before on stock it was like 70C Also it was a b*tch to fill without a fill port
Sweet!!!! Glad to see the decrease in temps!
Wave that fist anymore.... Lets see how fast I get it done!....
Sorry mastah ... I be a good b*tch I promise
hey Shaun, looks good bro, if you would only clean up your cables, that'll be one sick rig .
Tip, all you need is to buy another fitting, screw it on the top and by corresponding tubing and run it to an accessible point in the case. See below, here is mine
If you look at the pic, my case has a little sliding compartment up top. I removed the compartment and just left the sliding cover. I ran a line up there and when I fill it I just remove the cap, fill it and cap it when done. Filling was never easier
No video card again
Silverstone Fortress I'm working at right now. Nowhere from being finished, but looks nicely clean till now, no?
You don't have like an HD2600 or something like that laying around?
Even I have an HD2600XT or an X1800GTO laying in my closet. (Although they are both up for sale...)
No I don't.. The onboard HD 3300 plays TF2 and L4D fine at 1920x1080 so I'm good. I'm just gonna wait for the HD 5000's, definitely not buying gefuck again.
So how is the Hammer treating you? Looks like it fits that board a bit better than my DFI, less ram restriction anyways.
It was a pain to install it, its huge and it barely has enough clearance between the sidepanel and it, tight fit.
Other than that, its a pretty good cooler, keeps the E8400 on reasonable temps with lowest fan speeds.
Separate names with a comma.