Recent content by AnarchistUK

I managed to get the following settings in the BIOS... CPU Config = Manual Ratio = 21 FSB = 190 vCore = 1.35 CPU is now clocked at 4Ghz It doesn't go above 73 degrees

The hosts said it has restricted the php limit to 20MB. So now what do I do? So I have unlimited bandwidth, used only 14% of my web disk quota, but I am being restricted to the php limit and I cannot use my website anymore. Does the php memory need flushing out? How have I reached my limit...

Hello guys, I am tired of my current hosts. My personal website (www.area3d.co.uk) keeps dropping offline ever since I signed up with them 2 months ago, all they ask me is if the website is working now. It drops offline for 5 - 30 minutes, so by the time they look at it, then it's back online...

I'd like to have another fan for the push/pull.... The chassis fan which sits on the side plastic window uses the cables directly from the power supply. I'd have to look for 1 of those instead and I'm guessing all 120mm fans have the same positioning on the screws so it will fit into the...

I never touched the power output at all. It will be on Auto. What would be recommended for my rig? I'm very new to overclocking! The only thing I changed was bus speed from 133 to 200. It's stable at that and ran at the temperatues mentioned above, but Prime95 didn't like it and crashed after 1...

OK I overclocked this to 4.2 Ghz Is this OK or a bit too hot? 42 - 46 idle 70 - 76 load BEFORE Overclocking: AFTER Overclocking:

I've got Bad Company 2 on with maximum details. It's hovering around 46 degrees. I`ll go ahead and overclock now!

Looking at the 1st picture... it says "120mm Corsair Fan Socket", that is the 4 way socket and is where the fan has been plugged in since installation. The confusing part was where the 3 way power cable for where the pump should have gone, as there were 3 options (as named above and you...

Ahhh actually I should rectify this and say the PUMP power is 3 pins and there are 3 available ports on the motherboard for this. The fan itself is a 4 pin and that went onto where the old stock fan was plugged into for its power. So I couldn't have gone wrong with the 4 pin.

Oh yeah, there are 3 possible sockets with 3 pins for the CPU Fan power. They are named CHA Fan 2 (where it is plugged into now), CHA Fan 1, PWR-Fan (the one I had it plugged into earlier).

I accidentally hit the power button, which turned off my PC and caused my BIOS to mess around! It couldn't find the BootMGR!!!! I removed the power and battery to reset, thank God I fixed that! The CPU is reading 40 degrees in BIOS, I'm now in Windows and it's saying 31-35 across the 4 cores...

The paste that comes with it is apparently quite good as it cures rather quickly. I did get a 3rd party paste just incase "Arctic Silver 5 3.5g Thermal Paste". As I said the temp is down (averaging 46 degrees on idle), but it gave me a warning about the CPU fan not working, yet it is. What I...

I just rebooted and it's given a warning saying CPU Fan is not working, yet all fans in the computer are functional. I can feel the water passing through the 2 pipes too. I've uploaded pictures of my setup to my site. I've indicated where the fans are plugged into on the board. The rear fan...

Hi there, I've recently installed a cooler into my system. Prior to this I was getting 50 degrees idle and up to 80+ during load on the stock fan. I'm now getting the same readings after installing this water cooler! (44 degrees on idle right now). I've not even clocked it up to 3.80 Ghz yet...

OK just to add to this, my Brother's PC has the 'G0' version. Is this 1 of the better models? So, simply upping the multiplier affects only the CPU? This is actually all I want to do first and test it. See what heat builds up. I'm doing all of this from stock settings. I've gone into CPU...