W1zzard said:
can you post your equipment list?
just for other reviewers to know what is the right equipment to get accepted without any further discussion
you have a wicked sense of humor
(updated as of the last editing timestamp below)
Interface
National Instruments PCI-GPIB\LP NI-488.2 and cable
National Instruments PCI-DIO-96 w\ 2m 100 pin cable
(class status: need more RS232 and GPIB cables, need PIO breakout box)
Software
LABview 7.0
MATLAB & Simulink
DegreeC AccuTRAC
Keithley Runtime Environment
Autotest APG for Windows (3.0)
(class status: need to upgrade APG and like to add CFD modeling)
Measurment Hardware
Keithley 2700 Digital Multimeter & Data Aquisition System
Keithley 7701 32 channel Differential Multiplexer Module
Keithley 7708 40 channel Diff Mux Module w/ Automatic Cold Junction Compensation
Ametek 0-1000A Digital Recording Ammeter (AC)
Fluke 2176A 10 Channel Digital Thermometer w/ RTD
Digitec HT 5810 Thermometer
2 x Digidoc5 (fan monitoring) and rheobus fan controls
(Class Status: more or less complete, need more Rheobus controls, adding another dedicated HP 34401A DMM for the UTS-325)
Sensors
10 J Type Thermocouples with shielded extention grade wire
10 T Type surface mount Thermocouples
2x 4 wire RTDs
50x Thermistors (various makes and models)
10 calibrated J type panel connectors and plugs w\ strain relief in 2 handmade sheilded quickswap modular panels
27 x IHA-25 F.W. Bell Current Sensors
EESIFLO Sonic Low Flow, Mass flowmeter (pre-production prototype, temperature immune) being fabricated
Endress+ Hauser M-Point Massflow Meter
Setra 230 Wet/Wet Differential Pressure Transducer w/3-Valve Manifold
Keithley HA5050 50 Amp Shunt Sensor
American Aerospace Controls DC Current Sensor 913B-10-B
Micro Control Technology Calibration Module
(Class Status: need more RTDs and panel connectors, PCI\PCIe & AGP riser cards for the power consumption suite, need triple point cells (Hg \ H2O \ Ga) for in-lab calibration, need to have sensors professionally calibrated and their error curves plotted)
Electronic Enclosure Airflow and Temperature Test Suite
DegreeC Cambridge AccuSense ATM-24
24 x CAFS-220 sensors
AccuTRAC Software suite
Power Supply Testing Hardware
Panasonic VP 5720A Oscilliscope (GPIB w\ digital storage)
Ithaco Lock On Amplifier
Autotest UTS-325 PSU ATE
w\ 5 x 150W programmable DC load modules (1A /uSec slew rate for transient step mode) a total of 900 Watts test capacity
2.1 KVA Programmable Variac, Differential wideband peak detector, 12 position, 4 wire switching matrix, line source measurement, load current measurement, universal timer counter and software suite.
(Class Status:The Autotest UTS-325 is a completely integrated automatic test system,
The test suite includes: AC Line Current, AC Inrush, DC Line Current, DC Inrush, DC Line Step, Efficiency, Vout Setpoint, Voltage, Frequency, Sequencing,
Rise/Fall Time, Time Interval, Over/Under Shoot, Regulation Line, Regulation Line Frequency, Regulation Load, Cross Regulation, Regulation 2 Corner, Regulation 4 Corner,
Regulation Dynamic, Dynamic Transient Response, Noise & Ripple, OverLoad Constant Current, OverLoad Constant Voltage, OverLoad Short Circuit, Short Circuit Recovery
and Over Voltage Protection tests. Need to upgrade the EPROM and software.
Sound Testing Hardware
Bruel & Kjaer 2203 Sound Level Meter with 1613 Octave Filter Set
Bruel & Kjaer 4131 condenser microphone
Manfrotto Tripod Adapter
(Class Staus: need to build sound chamber)
Environmental Test Chamber Control & Measurement
PCon Multiloop PID control software
National Instruments PCI-DIO-96 w\ 2m 100 pin cable (listed above)
Omega CN77342-C2 Autotune PID Temperature Controller RS232
Rotronic HC321A Humidity & Temperature dewpoint Computer w\ Hygrometer
Kikusui PIA3200 GPIB Power Supply Control
Aquafine SP-1 UV Water Treatment Unit
100' 3\8" Anaconda Sealtite Isolated Ground Conduit
Aluminum Insulated Refrigerator door
3 Air conditioners
various blowers, pumps, insulation, sheet metal, metal stock, hardware, lumber and plumbing...Had
(Class Status: need solid state relays, power supplies, UV replacement bulb,
incremental improvements will be made as time allows and need dictates, increasing cooling capacity ect.
Phase2 of the chamber calls for tight humdity and temperature control based on Saturation Thermodynamics)
Infrastructure
2 computers for DAQ and Control w\ 2U rackmount Cases
Dual Opteron Workstation for MATLAB\CFD Modeling (244's\K8W\FX3000\4GB)
2 pair Heavy Duty Rackrails (had others)
Bud Industries Rackmount 30U Enclosure
5 surge proctetors
Olympus E20N
Lowel Tota halogen lights
Manfrotto 3251 heavy duty tripod and 3047 head
Welch Duo-Seal High Vacuum Pump Model 1400
CONDOR Linear DC Power Supply 5V@12A ±15V@3A 12V-15VDC
(Class Status: need centralized Online UPS approx 5KVA perferably Liebert, third computer for UTS-325,
fabricate vacumm chamber for thermal isolation, fabricate Calorimetry Tank)
and that isn't a fully itemized list