1. Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Noob need guidance w ATITool v.26 & AIW 9800 Pro

Discussion in 'ATITool' started by NCoastTweaker, Jan 31, 2009.

  1. NCoastTweaker New Member

    Joined:
    Jan 31, 2009
    Messages:
    24 (0.01/day)
    Thanks Received:
    3
    Location:
    Northeast Ohio
    I just loaded v.26 but I don't see any temp settings...
    ATITool_v.26 display.JPG

    I'm guessing the the AIW 9800 pro does not have sensors?

    Heres the log..

    2009-01-31 09:14:44 D Successfully connected to driver, version 130
    2009-01-31 09:14:44 D Scanning for ATI VGA Cards...
    2009-01-31 09:14:44 D Found ATI device: 0x1002 0x4E48 bus 1 dev 0
    2009-01-31 09:14:44 D fbPhy: 0xE8000000, mmrPhy: 0xFDFF0000.
    2009-01-31 09:14:44 D mmapped mmr to 0x8E70000
    2009-01-31 09:14:44 D BIOS at 0xC0000
    2009-01-31 09:14:44 D mmapped bios to 0x8E80000
    2009-01-31 09:14:44 D LM63 temp chip detection: failed (0x0)
    2009-01-31 09:14:44 D F75373 temp chip detection: failed (I2C)
    2009-01-31 09:14:44 D Temperature monitoring: Not detected
    2009-01-31 09:14:44 D Device initialized successfully
    2009-01-31 09:14:44 D Scanning for NVIDIA VGA Cards...
    2009-01-31 09:14:44 D Could not read driver's clock table: 2
    2009-01-31 09:15:24 I Scan for Artifacts started... Core: 378.00 MHz Memory: 337.50 MHz
    2009-01-31 09:15:24 I Scan for Artifacts running for: 0:00:00
    2009-01-31 09:19:59 D Successfully connected to driver, version 130
    2009-01-31 09:19:59 D Scanning for ATI VGA Cards...
    2009-01-31 09:19:59 D Found ATI device: 0x1002 0x4E48 bus 1 dev 0
    2009-01-31 09:19:59 D fbPhy: 0xE8000000, mmrPhy: 0xFDFF0000.
    2009-01-31 09:19:59 D mmapped mmr to 0x8E70000
    2009-01-31 09:19:59 D BIOS at 0xC0000
    2009-01-31 09:19:59 D mmapped bios to 0x8E80000
    2009-01-31 09:19:59 D LM63 temp chip detection: failed (0x0)
    2009-01-31 09:19:59 D F75373 temp chip detection: failed (I2C)
    2009-01-31 09:19:59 D Temperature monitoring: Not detected
    2009-01-31 09:19:59 D Device initialized successfully
    2009-01-31 09:19:59 D Scanning for NVIDIA VGA Cards...
    2009-01-31 09:19:59 D Could not read driver's clock table: 2
    2009-01-31 09:21:34 I Application terminated.
    2009-01-31 09:22:51 D Successfully connected to driver, version 130
    2009-01-31 09:22:51 D Scanning for ATI VGA Cards...
    2009-01-31 09:22:51 D Found ATI device: 0x1002 0x4E48 bus 1 dev 0
    2009-01-31 09:22:51 D fbPhy: 0xE8000000, mmrPhy: 0xFDFF0000.
    2009-01-31 09:22:51 D mmapped mmr to 0x8E70000
    2009-01-31 09:22:51 D BIOS at 0xC0000
    2009-01-31 09:22:51 D mmapped bios to 0x8E80000
    2009-01-31 09:22:52 D LM63 temp chip detection: failed (0x0)
    2009-01-31 09:22:52 D F75373 temp chip detection: failed (I2C)
    2009-01-31 09:22:52 D Temperature monitoring: Not detected
    2009-01-31 09:22:52 D Device initialized successfully
    2009-01-31 09:22:52 D Scanning for NVIDIA VGA Cards...
    2009-01-31 09:22:52 D Could not read driver's clock table: 2


    Can anyone offer a noob some help?

    Ok, just scoured thru the forum and found a thread that talks about an
    LM63 chip being required for temp readings with the ATITools... :-(

    Looks like I'm out of luck here....

    Is there anybody out there who can suggest some safe OC settings?
    (it would be nice if I could safely boost its performance a little)

    The card has a R350 core.
    Core clock / mem clock 380 / 340
    AGP Freq set to 67hz in bios
    Voltage is 1.5v
    MEM_TRCDRD 3
    MEM_TRCDWR 3
    MEM_TRP 3
    MEM_TRAS 8
    MEM_TRRD 4
    MEM_TWR 2
    MEM_TR2W CL+3
    MEM_TW2R_SAME_BANK Use TWR Rule
    MEM_TR2R 2
    MEM_WR_LATENCY 1.0
    MEM_MODE_REG 0x42
    MEM_CAS LATENCY 4
    MEM_CMD_LATENCY 0
    MEM_STR_LATENCY WR Latency
    MEM_REFRESH_RATE 0x29
    MEM_TRFC 17
    Last edited: Jan 31, 2009

Currently Active Users Viewing This Thread: 1 (0 members and 1 guest)

Share This Page