klootzakje
New Member
- Joined
- Sep 11, 2005
- Messages
- 39 (0.01/day)
- Location
- Netherlands, near A'dam
agp and pcie arent the same card though they do have the same core :O
Why not, it did worked on removing ram modules, Why should'nt it work on a gpu. With a good hairdryer with less air input can easy reach high tempertures. (try it with your hand on the air input) It much safer then an oven with 250 degress. I think we will see a Molex conector on the pcb melting away, if somebody is going to try it in the ovenDon__1 said:Not a chance in Hell but nice thought.
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
nope no pins just balls of solder...F!reF0X said::| no gpu pins?
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
sry dude i kinda disected the core (a peice of the die fell off and i was kinda like meh! f*** it! so i broke it in half lol )dolf said:Hi Klootzakje,
I was busy this week and no time left for core investigation. Tomorrow if possible I will prepare the material for Sean and probably when I receive the feedback (from Fresko also) and summarise it I will be ready to give some difinite answer about locking .
If you want to voltmod the card do it. The mod is not connected with my investigation.
Please, if you have time measure the resistance between the pads on the core where you haven't resistors (empty resistore places).
Successfull modding
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
i only broke it in half cause i didnt think you where gonna get back to medolf said:Sean I am very sorry to hear that. But even now the core can help (hope that you have the correct part of the dissection - that with laser cuts).
If possible try to obtain the following information:
1. (On the back side 5/4 bridges) they should have joined end. Is this end is general for both 4 and 5 bridge groups?
2. If it is not general for 4 and 5 bridge groups try to discover to what is/are connected. (All resistors from the front side are connected to Ground. But it is possible some of them to use connection through the PCB - core ball).
The first possibility is connection of the bridges to GND, the second one is to have direct connection to +3.3V (top of the front-side bridges). The third possibility is connection to ball (pin) from the core.
3. If you discover connections with these points, please cut the remaining bridges one after other and see whether the zero ohm connection is changed and to what (which ball, point from the front side)?
4. Can you find direct connection between not joined bridge part for every single end (after cutting) to ball of the core (or resistor on the front side)?
For me is interesting only the core-side with bridges (I hope). This information could be crucial .
Thanks in advance for the support and time spend but all that is done just for the community not personally for me .
Processor | opteron 165 |
---|---|
Motherboard | dfi cfx3200 |
Cooling | zalman 7000 |
Memory | mushkin xp4000 |
Video Card(s) | x1900xt |
Storage | 4x320 7200.10 raid |
Display(s) | 21" sony trinitron |
Case | v2000b lianli |
Audio Device(s) | x-fi platinum |
Power Supply | pcpac 510 |
Software | gaydows |
eeirertomb said:dolf your the best i just unlock the pipes!
eeirertomb said:dolf your the best i just unlock the pipes!
ChAce said:If you get 2ns your chances of XT PE speeds are virtually zero. You need 1.6ns ram And if you're going for PCI-E, get the GTO2.