Recent content by alexaligh

So i have this problem for a while now , all 15.x drivers has this same behavior . When i installed a 15.x driver , i always got a black screen whenever i turn on my computer . I think my pc still working normally , except the monitor just show a blank black screen . I had to restart and...

I found it , just tick the 'Start with Window' and it's good to go , thank for the help guys , appreciate it .

I have a question , how do you keep MSI Afterburner fan curve active even when you turn it off ? If that not possible , how to make it auto turn on everytime i start my pc ?

Awesome , i'll give it a try

I'm in , although i don't have enough Thanks , everyone please give me thanks so i can enter the giveaway , i will thank everyone in this thread , thank you all very much . I always have a soft spot for RPG and the Witcher series is one of the best , so naturally i want a taste of one of the...

Oh man , it worked , i take out the card , clean the fan , apply new paste and use MSI Afterburner and adjust fanspeed exactly as your . Just tried Rome 2 max setting again and this time it's 71C max . That is prrety good i think , the problem is fanspeed is up to 80% at that point and it sound...

Airflow is ok i think , plenty of room in my case with 1 fan in front and 2 fans uptop , i will try to turn fanspeed up cause i wear headphone anyway OK , this may be the simplest solution yet most effective , i think this will definitely work :D OK , I got this 2 years ago , might need some...

So today , when playing Rome 2 , i decided to turn graphic settings to maximum just to test my gpu . After a 30 min battle , i checked HardwareMonitor and was horrify by the max gpu temp , 83C degrees !!! Is that too hot for my gpu ? The fan was at 50% when that happen , should i increase...

Alright , so for a quick update , i use Realtemp for Cpu temp monitor and GPUZ for gpu temp . I had tested a few games and apps , so far so good , my CPU rarely goes over 60c and my GPU is 65c at most . Still , i will keep an eye on temp to make sure nothing unusual go unnotice .

Ok , so i take out the cooler once again , and tighten all the screw connect to the motherboard , then i remove thermal paste on both cpu and heatsink . Then i apply thermal paste again , this time on the heatsink , then i put all back on . I also tie some psu cable to make more room in the case...

Thank you guys very much , i figured out how to correctly put the fan and heatsink together . Now the temp is about 35-40 degrees on idle which is ok i think . Is this temp acceptable though ? i think idle temperature should be below 30C degrees . Another problem is i'm tested my cpu with prime...

well , i have the Gaia model , it's all the same with all the screws and the backplate , the only different is the damn rubber fastener . I think they send me the wrong rubber fastener kit :(

i just removed the cooler , removed the fan , erased thermal paste on both the cpu and cooler . Then i place new thermal paste on cpu , and put the cooler back on , but without the fan ( i think i might put it the wrong way , not sure ) . This time around , temp on all 4 cores fluctuate around...

Is this too high , on idle all 4 cores is about 70C degree , i'm using Xigmatek Gaia air cooler and the Thermal Status on all 4 cores is LOG

So , a friend of mine want to sell me his old rig : 1. Main Asus Rampage IV Extreme. 2. Chip I7 3820. 3. Kit Ram 4x4gb Gskill Ripjaw Z bus 2133. 4. Cooling Thermaltake Water 2.0 Extreme - CLW0217. 5. EVGA GTX 580 Classified 3GD5. 6. Scythe Kaze Master PRO 5.25 inch Black Fan Controller. 7. PSU...