- Joined
- Jan 29, 2023
- Messages
- 1,690 (2.01/day)
- Location
- France
| System Name | KLM |
|---|---|
| Processor | 7800X3D |
| Motherboard | B-650E-E Strix |
| Cooling | Arctic Cooling III 280 |
| Memory | 16x2 Fury Renegade 6000-32 |
| Video Card(s) | 4070-ti PNY |
| Storage | 500+512+8+8+2+1+1+2+256+8+512+2 |
| Display(s) | VA 32" 4K@60 - OLED 27" 2K@240 |
| Case | 4000D Airflow |
| Audio Device(s) | Edifier 1280Ts |
| Power Supply | Shift 1000 |
| Mouse | 502 Hero |
| Keyboard | K68 |
| VR HMD | Steam Deck OLED |
| Software | EMDB |
| Benchmark Scores | 0>1000 |
My last wish is to repaste/repad my GPU...
... then when i want i can do it with my 4070-ti with ease (once trained all always becomes easier).
It lost 4<7°c when i applied MX4 to the chip, but this time i'll use MX5 and change the therm pads too.
3060XC : TPU review //\\ Paste and Pads
Thanks for advices. especially dimensions, i don't read same as what i view on photos !!
//
Also, i will have to do the Z390M-Plus Prime, motherboard, i search info about it for the pads thickness...
DIY : 6.5x1 cm + 7.5x1 cm
1mm ..? looks like !
SO :
120x20 (cut in two) Thermal Grizzly Minus
120x20 (cut in two) Gelid Extreme - my choice
ARCTIC TP-2 120x20 (cut in two)
ARCTIC TP-3 120x20 (cut in two)
Extreme Odyssey 120x20 (cut in two)
//
VRAMs can be cut out: 80x40x2mm scissor
Set of three VRAMs #1: 40x15x2mm
Set of three VRAMs #2: 40x15x2mm
Set of two VRAMs: 25x15x2mm
The EVGA 3060 XC has two sets of three modules, each roughly is 40x15x2mm and has an additional set of two modules with size of 25x15x2mm.
//
For 3060XC :
2x2cm (1mm ?) backplate
2mm... what do you think ?:
ALL dimensions of GPU internals:
TOTAL (in cm) of GPU internals (backplate 2x2 is covered by mboard leftovers). Gelid Ultimate but i'll miss a tiny piece... will use mboard leftovers again
8x1.5
+
7x0.5
+
4x1
Paste :
MX6 for all.
Looks like good ?
... then when i want i can do it with my 4070-ti with ease (once trained all always becomes easier).
It lost 4<7°c when i applied MX4 to the chip, but this time i'll use MX5 and change the therm pads too.
3060XC : TPU review //\\ Paste and Pads
Thanks for advices. especially dimensions, i don't read same as what i view on photos !!
//
Also, i will have to do the Z390M-Plus Prime, motherboard, i search info about it for the pads thickness...
DIY : 6.5x1 cm + 7.5x1 cm
1mm ..? looks like !
SO :
120x20 (cut in two) Thermal Grizzly Minus
120x20 (cut in two) Gelid Extreme - my choice
ARCTIC TP-2 120x20 (cut in two)
ARCTIC TP-3 120x20 (cut in two)
Extreme Odyssey 120x20 (cut in two)
//
VRAMs can be cut out: 80x40x2mm scissor
Set of three VRAMs #1: 40x15x2mm
Set of three VRAMs #2: 40x15x2mm
Set of two VRAMs: 25x15x2mm
The EVGA 3060 XC has two sets of three modules, each roughly is 40x15x2mm and has an additional set of two modules with size of 25x15x2mm.
//
For 3060XC :
2x2cm (1mm ?) backplate
2mm... what do you think ?:
ALL dimensions of GPU internals:
TOTAL (in cm) of GPU internals (backplate 2x2 is covered by mboard leftovers). Gelid Ultimate but i'll miss a tiny piece... will use mboard leftovers again
8x1.5
+
7x0.5
+
4x1
Paste :
MX6 for all.
Looks like good ?
Attachments
Last edited:
