- Joined
- Aug 12, 2013
- Messages
- 60 (0.01/day)
System Name | Nebula |
---|---|
Processor | Ryzen 9 7900 @5.4 GHZ |
Motherboard | Gigabyte B650 GAMING X AX |
Cooling | Custom Loop - Bykski 60mm x360 mm RAD + Byskski 45x360 mm RAD+ Barrow 30x360mm RAD + D5 Pump+Res |
Memory | TEAMGROUP T-Force Vulcan Alpha DDR5 Ram 32GB Kit (2x16GB) 6000MHz RED |
Video Card(s) | Asus Strix OC 3080 12G on Phanteks Glacier Chrome Waterblock |
Storage | Adata XPG S40G 1TB, Crucial MX500 1TB, WD SN 570 1TB , Seagate Barracuda 2TB |
Display(s) | Acer XV272U 2560x1440 @144Hz |
Case | PC O11 Dynamic White, with Custom Front Fan Mod Total 13 Fans |
Power Supply | Phanteks Revolt Pro 850W |
Mouse | Cooler Master MM720 |
Software | Win 11 Pro |
Benchmark Scores | R23 Multi: 30K CPUZ Multi: 12450 |
I have Lian li O11 D original white case, i intent to use three radiators, fitment was not the problem at all. But airflow was bad.
I setupp fans as side and bottom intake and top exhaust. Since Side and Bottom both intake has radiator(s) it heats the air coming into the case.
I realized any intake air from the fans on the radiator(s) is actually warm-hot when pc is in load, and it re-circulates to other rads eventually warming them instead.
So if i had to use 3 radiators all radiator fans on them should blow air out of the case and not it. But case should have cold air coming in too...
I modded my case for better air flow and got my self front mesh kit. Used this: LINK
so for this mode i added:
1. LINK 92mm FR-925 RGB WHITE- on rear side, as Intake - Used Sillicon tappe to set the fan in place
2. LINK Lian Li O11 D Evo front mesh Kit - Used Neo Dymium magnets to lock the panel in front, since original o11D does not has the fitment for it. Added 3 fans as intake sticking with mesh.
4. I have now Top: 60x360mm + 30x360mm Radiator on bottom + 45x360mm Radiator on Side all Fans are exhaust
5. I think it had worked out ok, except from side there's 0.8mm gap due to magnets and fans in front.
What u guys think??
PP
I setupp fans as side and bottom intake and top exhaust. Since Side and Bottom both intake has radiator(s) it heats the air coming into the case.
I realized any intake air from the fans on the radiator(s) is actually warm-hot when pc is in load, and it re-circulates to other rads eventually warming them instead.
So if i had to use 3 radiators all radiator fans on them should blow air out of the case and not it. But case should have cold air coming in too...
I modded my case for better air flow and got my self front mesh kit. Used this: LINK
so for this mode i added:
1. LINK 92mm FR-925 RGB WHITE- on rear side, as Intake - Used Sillicon tappe to set the fan in place
2. LINK Lian Li O11 D Evo front mesh Kit - Used Neo Dymium magnets to lock the panel in front, since original o11D does not has the fitment for it. Added 3 fans as intake sticking with mesh.
4. I have now Top: 60x360mm + 30x360mm Radiator on bottom + 45x360mm Radiator on Side all Fans are exhaust
5. I think it had worked out ok, except from side there's 0.8mm gap due to magnets and fans in front.
What u guys think??

Last edited: