My 9600pro

[The Rage]

Hello i just downloaded ATITool 0.0.22 and have been running it with my card. my defaults are 398.00/304.00 and i have overclocked to 450/305 96/105FPS 107AVG. im just wondering how far i can go for it be safe and not blow my card up. i have put some heatsink compound on the fan/heatsink, so i hope that might cool it off a bit, i have a PCI fan below it blowing the hot air that comes off the heat sink out the back of my case. how far has everyone safely overclocked theirs? oh and my card is an ATI so i can flash it to a FX....or i havnt found a way..

 

[Qwerty]

the memory is at the top endish of the spectrum but you clock should go another 50mhz easily, My 9600 series (none pro, se, xt) runs at 505/303

Qwerty

 

[The Rage]

well i got it up to 490, it wouldnt go past 499 cuz it was generating artifacts

 

[Qwerty]

on a pro
thast seems weird they usualy go to 500 very easily, can your ram go higher maybe, the mem test is pretty safe on ati tools.

Qwerty

 

[The Rage]

if i find max memory it takes my core clock down

 

[The Rage]

im sitting at 489.86/300.86 97-115FPS 108AVG

 

[Qwerty]

find max memory then reset the cire afterwards. Manulaly


Qwerty

 

[The Rage]

490.91/326.45 97-122FPS 113AVG it didnt take my clock too far down, only to about 480

 

[Qwerty]

youve got better ram on it tahn mine, mine gets realy i=unstable past 310, i can take my core up to 550 though (need more cooline after pronlonged use dow), anyone got any idea oin were the heat sensoer would be locatdeso i can check if my card has one (its visualy identical to the abit 9600xt 256)

Qwerty

 

[The Rage]

i dont even think mine has one...im going to check ati's website

 

[Qwerty]

only the xts come with them as standard but some gfx cards have them on board but not enabled.

Qwerty

 

[Thomas_w]

HI.
This the info i can find on my CLUB3D Radeon 9600pro card.
I have just dl softmod.wxp-w2k-catalyst-8-062-040929a-018115C
and i am using ATI TOOL 0.0.19

How far should i be able to clock this card without destroying anything?

Graphics Processor Properties
Video Adapter ATI Radeon 9600 (RV350)
GPU Code Name RV350
PCI Device 1002 / 4150
Transistors 76 million
Process Technology 0.13u
Bus Type AGP
Memory Size 128 MB
GPU Clock 398 MHz
RAMDAC Clock 400 MHz
Pixel Pipelines 4
TMU Per Pipeline 1
Vertex Shaders 2 (v2.0)
Pixel Shaders 1 (v2.0)
DirectX Hardware Support DirectX v9.0
Pixel Fillrate 1592 MPixel/s
Texel Fillrate 1592 MTexel/s

Memory Bus Properties
Bus Type DDR
Bus Width 128-bit
Real Clock 297 MHz (DDR)
Effective Clock 594 MHz
Bandwidth 9504 MB/s

Graphics Processor Manufacturer
Company Name ATI Technologies Inc.

Amd Athlon 2400+
2x512 pc3200 ram
Asrock a7vm2

 

[The Rage]

i have mine at 490.50/326.25 safely, i cant get above 500 with my core cuz i start generating artifacts. and i dont get above 90deg F. i have an external temp monitor on the heat sink of my video card.

 

[ReconCX]

yea, that looks right, around 500/325 i believe is the best it can do. I'm using a 9550 and it's reaching it's limit somewhere around there.

 

[Thomas_w]

Strange.... I can`t get it higher than 440/330 without artifacts.

 

[Ramine]

try a flash to an XT mine runs at 150AVG, and ranges upto 170 fps

Ramine

 

[C&C Freak 2K]

Just FYI, if I remember correctly the RAM is designed to clock up to 350MHz.

 

[Thomas_w]

Well i am kind of new in all this, so flashing the card scares me a little. Can`t it go wrong so the card dies?

Does some of you have a link to a guide that tells how to flash the card?

 

[wazzledoozle]

Dont flash your 9600 series cards- there is no benefit. The core will not clock any higher. If you really wanted to permanently change your memory timings i guess you would, but no other reason.