• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.
  • The forums have been upgraded with support for dark mode. By default it will follow the setting on your system/browser. You may override it by scrolling to the end of the page and clicking the gears icon.

*X800XTPE Volt Mod*

armaniazn1

New Member
Joined
Sep 17, 2004
Messages
2 (0.00/day)
Hi all,

I'd just like to know if any of you have successfully done a pencil volt mod on an X800 XT PE?
If so, how did you do it, and to what voltage was it done?

I have a His IceQii X800XT PE and am currently stuck at 550 maximum core speed and 570 maximum mem speed when overclocking and am trying to get over this apparent wall.

Any help would be appreciated. Thanks and have a nice day!
 
works here too!
radeon%20pmod.JPG
 
anybody feel like finishing off the x800 voltmod article here? pics are there just needs some text
 
W1zzard said:
anybody feel like finishing off the x800 voltmod article here? pics are there just needs some text
Short version:
The top picture shows the pin where you measure the voltage. You have to do this while the card is running.
The second picture shows a resistor. Take a multimeter and measure the resistance on it. It should be around 420. Now take a pencil and draw around the resistor. (Follow the green line)
The pencil should make contact with the resistor while you do so.
After a few strokes measure the Ohms on the resistor again. A around 380-385 you're at 1.5v vgpu usually. This may vary slightly from card to card so don't make too huge steps.
15 ohms less are 0.04volts more roughly.

I hope this helps.

Those pics above are taken from another site btw.
 
Last edited:
W1zzard... no one stepped up to finish the volt mod article?
 
nope .. all i need is someone to write it together .. i can supply measurements, data etc.
 
Like you time is a premium... I've done the pencil volt mod on the VIVO pro and vmem, droop mod on my ASUS board. So I'll try to do a section at a time with your pics... send me an email where you want me to send it ....
 
email to w1zzard@techpowerup.com .. you can also make a forum post here and work on it here ... post a reply to the x800 voltmod article then keep editing this post till its finished
 
Jason ... did you do the work yourself ?
 
Screeming ... not using stock HSF still ?
 
Any way any of you kind fellows could show where to do a volt mod on the memory with pencil?
 
Jason, could you share a bit more info on where the other ends of the wiring are connecting to. I have heard of folks attaining speeds like yours, but thought they were just cutting up. I see now that it can actually be done. I am quite capable of doing the soldering work. And I know there are risks. But I am willing to take it. I sent you a PM also, hoping to get in touch with you one way or another. It's amazing that you can get that kind of speed out of the core and memory chips. Geesh.
 
NukeleaR said:
Any way any of you kind fellows could show where to do a volt mod on the memory with pencil?

I don't think there is a pencil mod for the memory m8.
 
NukeleaR said:
Any way any of you kind fellows could show where to do a volt mod on the memory with pencil?

With time permiting I'm hoping to finish the pencil mod section for W1zzards X800 volt mod
here this weekend . It'll be a step by step " How To" ... for both the resistor and pencil mod...
 
Urlyin said:
With time permiting I'm hoping to finish the pencil mod section for W1zzards X800 volt mod
here this weekend . It'll be a step by step " How To" ... for both the resistor and pencil mod...

weekend?
can u make it earlier pls~~~ :p
 
Last edited:
Should have some time tomorrow night to finish the pencil mod section that will also have the vdd(vmem), vddq vmods as well

W1zzard anything on the Vddq measure point?
 
Urlyin said:
Should have some time tomorrow night to finish the pencil mod section that will also have the vdd(vmem), vddq vmods as well

W1zzard anything on the Vddq measure point?

awesome, thx alot~~
 
Last edited:
W1zzard I found the measure point on the backside for the VDDQ... cap c110 the two silver dots backside of the capacitor ... bottom one if facing the top of the card
 
So there is a pencil memory volt mod? I need to know how and where on the card. Like what kind of numbers am I looking for on my didgital multimeter, before and after using the pencil graphite.
 
Quazi said:
So there is a pencil memory volt mod? I need to know how and where on the card. Like what kind of numbers am I looking for on my didgital multimeter, before and after using the pencil graphite.

Read the article here
 
Noob question alert!

hehehhe, ok, for the vmods, will 50k vr's work in place of the 10 and 20k vr's? I assume so, but we all know what happens when ya assume :eek:

TIA,
E
 
Back
Top