• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

EK Launches Precision Torque Screwdriver

U

Uskompuf

Joined
Mar 31, 2020
Messages
1,519 (0.82/day)
EK, is launching the EK-Loop Torque Screwdriver 0.6 Nm to provide its customers with the best and safest tools for their liquid cooling adventure. Assemble and maintain your water-cooling equipment without the risk of over-torquing and damaging your gear. EK is dedicated to being a one-stop shop for its users, making their loop-building experience easier and more accessible.

EK-Loop Torque Screwdriver - 0.6 Nm is a precision screwdriver that will allow you to precisely fasten screws. This screwdriver includes the 5 most common bits used for PCs and liquid cooling. It is set to 0.6 Nm torque. Upon reaching this force, an audible click is produced and the screwdriver resets. This way, you can no longer break your parts by using too much force as this tool will not allow you to. The soft-grip handle is made of TPR for comfortable use while building a loop.





Parts

  • EK-Loop Torque Screwdriver - 0.6 Nm
  • TX10 (Torx)
  • PH1 (Phillips-head)
  • PH2 (Phillips-head)
  • HEX 2.0 mm (Allen)
  • HEX 2.5 mm (Allen)

Availability & Pricing

The EK-Loop Torque Screwdriver is now available worldwide for a MSRP of 19.90 €.

View at TechPowerUp Main Site
 
Well, i guess if your the ham fisted, neanderthal type this might come in handy. No pun intended. Otherwise common sense should and has prevailed for the majority of us.
 
Lately they are becoming joke of themselves.

Their manuals do not state the needed amount of force. The manuals are often lacking information.

Tighten the screws evenly. Do not use excessive force when tightening the screws.
Click to expand...

Basically it is all bullshit again. I still would not use few penny screwdriver like that, after few times it most probably becomes loose, especially in hands of those who tend to overtighten screws.

Also I can bet... 6cNm are way too weak for some screws. 6-14 cNm is the needed force. I am tightening screws in mobile phones 6-12cNm according to the manufacturer manual. And those are ~M1.2
 
Last edited:
no RGB?!
hard pass.
 
Torq screwdrivers have been available for years and the best ones come with magnetic tips. This is a poor attempt from EK.
 
Starts from 0,6 newtons to 20 Nm?
 
Is this how EK plans to get away with using subpar screws that strip easily?
 
Not a bad idea. I bet loads of people waay over tighten the screws when building a PC.
 
Ferrum Master said:
Care to share your experience to us?
Click to expand...
I don't have any personal experience.
Recently there were quite a few posts on Reddit complaining about stripped screws (sometimes even stripped from the factory). The timing of EK suddenly releasing a torque screw driver seems awfully convenient.
 
Follow the guidelines/rules.
Here are a couple of quotes from them:
Avoid political or religious comment unless it is specifically relevant to a topic and in those cases is only acceptable if done in an unbiased manner.
Click to expand...
All posts and private messages have a "report post" button on the bottom of the post, click it when you feel something is inappropriate.
Click to expand...

Thank You.
 
claster17 said:
I don't have any personal experience.
Recently there were quite a few posts on Reddit complaining about stripped screws (sometimes even stripped from the factory). The timing of EK suddenly releasing a torque screw driver seems awfully convenient.
Click to expand...
So no actual fact or firsthand experience, just hearsay?
 
You must log in or register to reply here.
Back
Top