Help me to OC my 5700X

[BlaezaLite]

I've been bitten by the bug that is overclocking once more due to Cinebench 2024 and would like a fast yet stable OC. Anyone able to guide me through this process please? I've tried myself and started getting worried about 11 thousand different things you can alter and it overwhelms me.

 

[jayjr1105]

Just enable PBO +200Mhz, research your chip and set PPT, TDC, and EDC appropriately and figure out what your chip can do on curve optimizer (start at -5 on all cores).

Here's a good thread on PBO settings for the 5800X, should be very similar for your chip https://www.techpowerup.com/forums/...-3-chips-pbo-settings-temperature-fix.283776/

 

[BlaezaLite]

Thank you for your advice and advising me on that thread. I've been in that thread before and just come away with information overload. I will try harder to understand what's being said.

 

[izy]

I can tell you my settings, pretty good results. +200mhz, boosting to 4600-4675 in CB all core , 4850 single core, temp 78-80C in all core.

 

[BlaezaLite]

@izy So I'm trying to input your settings using Ryzen Master as I can't find PBO2 to download. How would I up the max boost in Ryzen Master? I can't see max boost anywhere or am I really just box of rocks dumb?

Is Ryzen Master an over-complicated steaming turd or am I imagining it?

So I found PBO2 already on my pc somehow, but the max boost setting won't change despite inputting it multiple times.

 

[izy]

@izy So I'm trying to input your settings using Ryzen Master as I can't find PBO2 to download. How would I up the max boost in Ryzen Master? I can't see max boost anywhere or am I really just box of rocks dumb?

Is Ryzen Master an over-complicated steaming turd or am I imagining it?

So I found PBO2 already on my pc somehow, but the max boost setting won't change despite inputting it multiple times.

My settings were done directly in BIOS, i only used PBO2 Tuner to tune/test the Curve when i did it first time and to show you my settings.
With PBO2 Tuner if PBO is not on AUTO in BIOS (or Enabled or something like that) it wont change the max boost clock , and the max boost value you can use is 4850mhz , higher values wont work, i used +200 mhz in bios under "Max CPU boost overdrive" or what is called.

Your Curve values should be different than mine anyway but i think its safe to start with -20 on all cores and use CoreCycler + OCCT to test and tune with PBO2 Tuner. I think i started with -25 on all cores then i used CoreCycler to see which core fails and changed the values based on that, when everything was OK on CoreCycler i used OCCT to check stability and i think i went 1 step less on each core than what my CPU could do to be sure its stable , never had a problem.

 

[BlaezaLite]

During the night (Not slept yet) I figured that out, lol. My chip is worse than yours as it won't get near your scores on Cinebench 24. 850 is the highest I remember so you have some golden sample or something.

Thank you for your help, always appreciated.

 

[izy]

During the night (Not slept yet) I figured that out, lol. My chip is worse than yours as it won't get near your scores on Cinebench 24. 850 is the highest I remember so you have some golden sample or something.

Thank you for your help, always appreciated.

I tunned it for couple of days when i first got it , its all about the temps (they shoudnt go higher than 80C after tune in CB) and the Curve, you should try each core with CoreCycler to find the max stable curve you can go on each core. I also have FCLK at 1867 , that gives a boost to multicore too , now i have 4x RAM sticks with 2 different kits and i had to change my RAM timings to bad values as the second kit sucks, this is the best i could get with them , i had to increase ProcOdt to 48 and GDM on to get it stable even with this crap timings.

What are your Curve values and FCLK?

 

[GerKNG]

find out if +200 with a 2x scalar only is stable and then put a negative CO offset ontop of it.

 

[BlaezaLite]

Curve values are still up in the air at the moment, as I am nowhere near finished. FCLK is 1600 as I'm running ram at XMP 3200.

 

[bart1903]

I can tell you my settings, pretty good results. +200mhz, boosting to 4600-4675 in CB all core , 4850 single core, temp 78-80C in all core.

View attachment 315304View attachment 315305

I can tell you my settings, pretty good results. +200mhz, boosting to 4600-4675 in CB all core , 4850 single core, temp 78-80C in all core.

View attachment 315304View attachment 315305

you are legend mate just want ask if you live your voltage on auto or change anytching

@izy

you help me a lot was looking for few days for pb02 how to setup thank you so much

 

[izy]

you are legend mate just want ask if you live your voltage on auto or change anytching


you help me a lot was looking for few days for pb02 how to setup thank you so much

Voltage on auto, thats what Curve Optimizer is doing already, i only increased the voltage for my RAM after RAM OC.

 

[bart1903]

I can tell you my settings, pretty good results. +200mhz, boosting to 4600-4675 in CB all core , 4850 single core, temp 78-80C in all core.

View attachment 315304View attachment 315305

if you can explain how to setup pb02 strtup witch win10 that would be great