beta 15 and beta 16 pre3 bugs with X1600pro

[BuzaL]

Hello,

I tried first the beta 14. It was fine, but show my pipelines 4 instead of 12.
I used the beta 15. I can't changed clock/mem. with this revision.
I checked the newest, the beta 16 pre3. I try to set back my settings to default: get freezed. (blue horizontal lines, and full hangup)
I checked the X1000 settings. I played for some minutes and I turned off the "Override BIOS parsing for finer clock control". Then the tool getting better.
BTW, the b16pre3 show my pipelines 4 too.
Some lines from the log:

2006-10-14 04:38:54	D Successfully connected to driver, version 124
2006-10-14 04:38:54	D Found ATI device: 0x1002 0x71C2 bus 1 dev 0
2006-10-14 04:38:54	D   fbPhy: 0xE0000000, mmrPhy: 0xBF800000.
2006-10-14 04:38:54	D   mmapped mmr to 0x1840000
2006-10-14 04:38:54	D   BIOS at 0xC0000
2006-10-14 04:38:54	D   mmapped bios to 0x1850000
2006-10-14 04:38:54	D  LM63 temp chip detection: failed (0x0)
2006-10-14 04:38:54	D  F75373 temp chip detection: failed (I2C)
2006-10-14 04:38:54	D   Temperature monitoring: Not detected
2006-10-14 04:38:54	D  VT1103 chip detection: failed (0x0)
2006-10-14 04:38:54	D Device initialized successfully
2006-10-14 04:38:54	I Suspending ATI2EVXX.EXE 956
2006-10-14 04:38:54	I Suspending ATI2EVXX.EXE 1268
2006-10-14 04:39:01	I Loading profile 'X1650Pro':
2006-10-14 04:39:01	I   Core clock: 499.50 MHz -> 600.75 MHz
2006-10-14 04:39:01	I   Mem clock: 391.50 MHz -> 441.00 MHz
2006-10-14 04:39:01	I Done

And here some info from Overclocking section, which doesn't appeared in the LOG:

GB_PIPE_SELECT = 0x1E4

Regards.: BuzaL

p.s.: does anyone know, why running 2 ATI2EVXX on my PC?

 

[KennyT772]

x1650=x1600xt with slightly higher clocks. 4 pipes 12 shaders

 

[ARTOSOFT]

Use 0.25 beta16pre1 instead of 0.25 beta16pre3 for x1600pro.

It is correct to show 4 pipelines. IIRC, that's actual hardware pipelines. Each pipelines capable of rendering 3 pixel => 12 virtual pipelines.

Regards,
Arto.

 

[BuzaL]

Thanks, Arto!

I will check it.
But Kenny, i haven't got X1650, it's just the profile name, which i used. 'Cause the X1650Pro had same GPU with DDR3, but on 600/500.

Nobody knows why running two instances of the ATI2EVXX.exe ?
(It is remained too, when i disabled the secondary monitor)

BuzaL

 

[JC316]

Those are clock switching programs for the X1800 series, not sure what the effects are for the X1600 series. They change from 2d to 3d clock speeds.

 

[ARTOSOFT]

Thanks, Arto!

I will check it.
But Kenny, i haven't got X1650, it's just the profile name, which i used. 'Cause the X1650Pro had same GPU with DDR3, but on 600/500.

Nobody knows why running two instances of the ATI2EVXX.exe ?
(It is remained too, when i disabled the secondary monitor)

BuzaL

Where you found 2 instances of ATI2EVXX.exe? I don't have it run on my processes Windows Task Manager, not even a single instance.

Regards,
Arto.

 

[GeckOblue]

Beta 16?

I cant change the mem/gpu clock either (I also have an X1600). But I dont see anything for the ATI Tool 0.25 Beta 16... -currently using the only DL i see, the beta 15.

 

[GeckOblue]

-Oh, there it is, buried in the forum, just had to do some digging. Thanx anyway.

 

[Agility]

ati2evxx.exe is a process installed alongside ATI Display Adapters and provides additional configuration options for these devices. This program is a non-essential process, but should not be terminated unless suspected to be causing problems. If you want to check then go to this http://www.liutilities.com/products/campaigns/plib/rbplib/ to check for errors.