- Joined
- Mar 8, 2008
- Messages
- 265 (0.04/day)
- Location
- Anaheim, California
| Processor | 9800X3D |
|---|---|
| Motherboard | Gigabyte X870 Aorus Elite WiFi7 ICE |
| Cooling | ID Cooling FX360 Pro |
| Memory | TEAMGROUP T-Force Delta RGB DDR5 Ram 32GB 7200mhz |
| Video Card(s) | EVGA FTW RTX 3090Ti |
| Storage | Acer Predator 4TB NVME |
| Display(s) | Viotek GNV34DBE2, Viotek SUW49DA |
| Case | Hyte Y60 |
| Power Supply | Corsair RMx1000 white |
| Mouse | Glorious Model O |
| Keyboard | KBDFans Odin V2 |
| Software | W11 Pro |
To view this case mod, go here.
Specs:
C2D E6750 w/ lapped TRUE120
8800GTS 640mb w/ HR03+
x1 74GB Raptor HDD
x2 300GB Seagate HDD
PC P&C Silencer 750w PSU
Mods:
Well first I used a 1 inch hole saw to cut several holes out behind the motherboard and throughout the case, to allow for better cable management. Then I put rubber grommets on the walls of those holes that I cut out, that way the cables I run through there wont get snagged or damaged on the rough edges. I also had to pull out the dremel to cut into the case a little to ease the cable management. I took a close up of where I cut out. After some heavy planning I went through and routed the cables anywhere could where they would be the least visible. I dont thing anyont notice but I fit a 120mm fan down in front of the lower hard disk drive cage. In order to do that I had to remove a piece that was held down by rivets, but they easily popped out with a flat head screw driver. I will make another log of my earlier cable management pics too so others can see how that was done. I have lots of pics and several revisions of cable management on the Antec P180.
To top it off I painted my case in mid-February to give it some added luster, lol. I used Dupli-Color bumper black and also the Sandable Primer. I included some pics of the primer process and a few pics of the painting.
PM with question, comments, suggestions, etc.
Specs:
C2D E6750 w/ lapped TRUE120
8800GTS 640mb w/ HR03+
x1 74GB Raptor HDD
x2 300GB Seagate HDD
PC P&C Silencer 750w PSU
Mods:
Well first I used a 1 inch hole saw to cut several holes out behind the motherboard and throughout the case, to allow for better cable management. Then I put rubber grommets on the walls of those holes that I cut out, that way the cables I run through there wont get snagged or damaged on the rough edges. I also had to pull out the dremel to cut into the case a little to ease the cable management. I took a close up of where I cut out. After some heavy planning I went through and routed the cables anywhere could where they would be the least visible. I dont thing anyont notice but I fit a 120mm fan down in front of the lower hard disk drive cage. In order to do that I had to remove a piece that was held down by rivets, but they easily popped out with a flat head screw driver. I will make another log of my earlier cable management pics too so others can see how that was done. I have lots of pics and several revisions of cable management on the Antec P180.
To top it off I painted my case in mid-February to give it some added luster, lol. I used Dupli-Color bumper black and also the Sandable Primer. I included some pics of the primer process and a few pics of the painting.
PM with question, comments, suggestions, etc.
Last edited by a moderator:
