New to me SanDisk X300 (2016 2.5" SATA SSD based on Toshiba/SanDisk/WD MLC flash and Marvell controller) that I installed in my ProBook 645 G1 today (has been power cycled a couple times):
=== START OF INFORMATION SECTION ===
Device Model: SanDisk SD7TB6S256G1001
Serial Number: XXXXXXXXXXXXX
LU WWN Device Id: XXXXXXXXXXXXX
Firmware Version: X3551201
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Dec 20 18:46:49 2022 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0032 100 100 --- Old_age Always - 0
9 Power_On_Hours 0x0032 253 100 --- Old_age Always - 16557
12 Power_Cycle_Count 0x0032 100 100 --- Old_age Always - 4818
170 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 0
171 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 0
172 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 0
173 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 35
174 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 125
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 --- Old_age Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 100 100 010 Pre-fail Always - 100
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 --- Old_age Always - 0
194 Temperature_Celsius 0x0022 069 062 --- Old_age Always - 31 (Min/Max 13/62)
199 UDMA_CRC_Error_Count 0x0032 100 100 --- Old_age Always - 0
233 Media_Wearout_Indicator 0x0033 091 100 000 Pre-fail Always - 15309210
234 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 26350
241 Total_LBAs_Written 0x0030 253 253 --- Old_age Offline - 19404
242 Total_LBAs_Read 0x0030 253 253 --- Old_age Offline - 37542
249 Unknown_Attribute 0x0032 100 100 --- Old_age Always - 7739
SMART Error Log Version: 1
No Errors Logged
Has half the active idle consumption of the 860 Evo I previously had installed in this system (< 100 mW vs 200 mW) and should also have better Linux and old AMD chipset compatibility:
Samsung 860/870 SSDs Continue Causing Problems For Linux Users
