• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

[solved(??)] 2.4Ghz ping spikes/packet loss on TP-LINK Archer C5 v2 AC1200 router

Status
Not open for further replies.
Joined
Aug 11, 2011
Messages
4,357 (0.87/day)
Location
Mexico
System Name Dell-y Driver
Processor Core i5-10400
Motherboard Asrock H410M-HVS
Cooling Intel 95w stock cooler
Memory 2x8 A-DATA 2999Mhz DDR4
Video Card(s) UHD 630
Storage 1TB WD Green M.2 - 4TB Seagate Barracuda
Display(s) Asus PA248 1920x1200 IPS
Case Dell Vostro 270S case
Audio Device(s) Onboard
Power Supply Dell 220w
Software Windows 10 64bit
EDIT:
SOLUTION: For my case, disabling IPv6 and setting the wireless to B/G only was the fix.

- Lag seemed to be fixed by disabling IPv6.
- The packet drop issue was fixed by disabling Wireless N. Only my Roku Express is affected by this but Wireless G is enough for streaming to the Express with it being 720p. The connection is solid and without losses so it's the preferable setup I suppose.



PROBLEM:
I have a TP-LINK Archer C5 v2 AC1200 wireless Dual Band router that experiences intermittent and seeming random ping spikes/packet loss on the 2.4Ghz band:

Capture532.png


The connection does not drop. The connection and signal keeps strong; is just that no data passes through the router intermittently at random intervals.

I have it connected to an ARRIS TG832 router in bridged mode but that isn't the culprit since a wired connection to the TP-LINK router doesn't present any kind of problem so it isn't ISP related.

I have also determined that the 5Ghz band doesn't suffer from the issue either. Running a ping while the 2.4Ghz band experiences packet loss shows a steady 2ms ping.



TROUBLESHOOTHING:

1. I ran a wifi analyzer tool and found that there is practically 0 congestion issues.

Capture531.png


Nevertheless, I went and setup channel 1 for the 2.4Ghz band although the auto setting had already selected it as shown in the screenshot. That didn't make any discernible difference.


2. I saw this wordpress post:

https://kempniu.wordpress.com/2012/09/13/wmm-and-delays-on-tp-link-routers/

and disabled WMM as indicated. Again, there's no discernible difference in performance.


3. This might be a clue: whenever the packet loss begins to happen, if I disconnect from the network and connect again the issue seems to go away. I tested by having two laptops side by side looking at the same youtube video. When the video chocked I re-connected to the network with one of the laptops and left the other as is. The laptop that reconnected to the network began to run the video right away while the other kept buffering for 10 more seconds or so.

I thought it was related to dynamic IPs so I set static IPs for them but that doesn't seem to help either.



CURRENT 2.4G SETTINGS:

Capture533.png

Capture534.png
 

Attachments

  • Capture531.png
    Capture531.png
    64 KB · Views: 1,697
Last edited:
I have read with some of the C5 V2 AC1200 units that disabling IPv6 might fix the 2.4GHz dropout issue, have you tried that?

Go to IPv6 support and uncheck IPv6 Enabled, reboot the device.

I would also consider changing to DD-WRT firmware to see if that helps resolve an issue with what could be a bug in the TP-Link firmware.
 
I have read with some of the C5 V2 AC1200 units that disabling IPv6 might fix the 2.4GHz dropout issue, have you tried that?

Go to IPv6 support and uncheck IPv6 Enabled, reboot the device.

I would also consider changing to DD-WRT firmware to see if that helps resolve an issue with what could be a bug in the TP-Link firmware.

Capture536.png



That helped immensely, although I still see some packet loss but the issue isn't as dire as before. ping average is down nevertheless, although still very far from optimal. Thank you very much for the suggestion. :D

I'll see if I can correct the situation 100%, if not I'll try DD-WRT. I don't know if the Archer is supported though.
 
Last edited:
No cordless phones right?
 
Still having the issue, although not as bad as before disabling IPv6
 
I finally got the 2.4Ghz band working fine. In fact what gave me the tip were the recent PS4 wifi issues.

I disabled Wireless N in the 2.4Ghz band and everything is peachy now (running just B/G). Bummer that you have to disable features in order to get a working connection. :banghead:
 
Last edited:
That is something to report to Sony and TP - link
 
Status
Not open for further replies.
Back
Top