• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.
  • The forums have been upgraded with support for dark mode. By default it will follow the setting on your system/browser. You may override it by scrolling to the end of the page and clicking the gears icon.

Super Pi 1m scores

Status
Not open for further replies.
I have a friend w/ same Mobo Asus Commando & a Q6600 @ 4.1GHz he needs 1.85 vcore but he is using watercooling so that might help... yeah pretty nuts eh but damn Q6600 65nm are tougher to break compared to 45nm's :rockout:

in 3Dmark06 hitting 60c+ on all cores as I remember but never reaches 70c...

damn and I thought you were nuts hehe, your friend is even crazier :).
 
I have a friend w/ same Mobo Asus Commando & a Q6600 @ 4.1GHz he needs 1.85 vcore but he is using watercooling so that might help... yeah pretty nuts eh but damn Q6600 65nm are tougher to break compared to 45nm's :rockout:

in 3Dmark06 hitting 60c+ on all cores as I remember but never reaches 70c...

Have you tried uping the VTT volts? This is from another thread: I finally got my Q6600 to 4006GHz with my 750W PSU being no problem.. i had the NB voltage 2 notches up as well as the VTT voltage and the CPU core voltage was 1.535V http://forums.techpowerup.com/showthread.php?t=70723&highlight=q6600+impossible
 
Have you tried uping the VTT volts? This is from another thread: I finally got my Q6600 to 4006GHz with my 750W PSU being no problem.. i had the NB voltage 2 notches up as well as the VTT voltage and the CPU core voltage was 1.535V http://forums.techpowerup.com/showthread.php?t=70723&highlight=q6600+impossible

what's VTT voltage? is it FSB termination? if it was FSB term I set mine @ max when doing 4.1ghz

here is my friends 1.85 vcore on Q6600 Vdroop to 1.792... insane eh...

superpi4104512453xh4.jpg
 
what's VTT voltage? is it FSB termination? if it was FSB term I set mine @ max when doing 4.1ghz

here is my friends 1.85 vcore on Q6600 Vdroop to 1.792... insane eh...

From ExtremeOcing http://forums.extremeoverclocking.com/t282072.html:
System Bus Input Supply Voltage, often referenced as FSB termination voltage (VFSB) simply the voltage the fsb is running on. logic levels on the fsb are relative to this voltage. higher vtt results in higher logiclevels and thus in increased noise ratios. increasing vtt might help overclocking.
 
From ExtremeOcing http://forums.extremeoverclocking.com/t282072.html:
System Bus Input Supply Voltage, often referenced as FSB termination voltage (VFSB) simply the voltage the fsb is running on. logic levels on the fsb are relative to this voltage. higher vtt results in higher logiclevels and thus in increased noise ratios. increasing vtt might help overclocking.

tnx for the tip but I set it @ 1.55 max on my Commando I think my Mobo is shitty on Quads :banghead:
 
One more score of my X2 5600 now @ 3.4 on a different board.

25.390s
 

Attachments

  • X2_5600_3415Mhz_SuperPI.jpg
    X2_5600_3415Mhz_SuperPI.jpg
    198.7 KB · Views: 388
Thought I might as well post it. Nothing special, but an improvement on my E2140.
10.563 - 4.4 GHz E8400
 

Attachments

  • superpi - 10.563.jpg
    superpi - 10.563.jpg
    64.5 KB · Views: 387
4.4 :eek: crap, air cooling? Not yet blown:p

No, I reckon go a higher but I'm getting bored. I can get to 4.5 easy, but I don't like how hot is gets (73*C, so I'm not going to bench at that, it's dishonest)
 
No, I reckon go a higher but I'm getting bored. I can get to 4.5 easy, but I don't like how hot is gets (73*C, so I'm not going to bench at that, it's dishonest)

ba...d I envy you:banghead::mad::mad::banghead:
 
ba...d I envy you:banghead::mad::mad::banghead:

I probably need a better cooler to be perfectly frank. This AC Freezer is getting on a bit. My case cooling is also a little dire. The case itself is at fault, it's too small and doesn't have enough vents. I do like the speed boost from my E2140 @3.4 though. Really noticeable.
 
Last edited:
I'm going to try for 4.2GHz tomorrow :D
 
today`s cascade warmup for tomorrow`s LN2 run..

 
^^^ WOWWWWWWW, nice, i could only imagine on LN2!!! :toast:
 
i expect ~200mhz more easily....after that,we must be lucky..
 
i expect ~200mhz more easily....after that,we must be lucky..

Is the chip more or less fried after that? Or does the LN2 cooling stop the damage to the gates?

Just wondering B/C i see the 1.9Volts and wondered if that chip would be useable after all the benchmarking runs?:toast:
 
We have only 1 dead cpu after benching with 7-8 on the event...
with -140C they dont need anything...work fine..
 
Update mine please!

465-1.jpg


This was one i done a while back, i'm still trying to get this board to boot at 523FSB. I'm not sure if its the board, or my ram holding me back. (I have to raise my performance level on the ram for it to boot above at 4.55+ghz (from 7 to 10)
 
today`s cascade warmup for tomorrow`s LN2 run..


Very nice OC and Pi run giorgos th. cant wait to see your LN2 runs ..... I need to get my Biostar Tpower insulated and see what I can with my 8600 on it maybe tomorrow i'll get it going and see what I can do.
 
I updated the list and send it to giorgos th.!
 
Last edited:
ok,list posted.
 
Status
Not open for further replies.
Back
Top