1st Player Steampunk PS-850SP 850 W Review 10

1st Player Steampunk PS-850SP 850 W Review

(10 Comments) »

Introduction

1STPLAYER Logo

We would like to thank 1st Player for supplying the review sample.


I reviewed the Steampunk PS-750SP more than two years ago. In this review, I will look at its 850 W brother. The PS-850SP, or Steampunk 850, is a fully modular power supply with the Gold efficiency certification from both 80 PLUS and Cybenetics. It is also rated Cybenetics Standard+ for noise output, which means it isn't quiet. I expected noise output to be lower with a 140 mm sleeve bearing fan and Gold-certified efficiency, but the extended warranty had 1st Player take the safe approach. That said, I am unsure about whether the sub-par fan will even outlive the seven-year warranty. Instead, a rifle bearing or fluid dynamic bearing fan would have been better.

With a capacity of 850 W, fully modular cable design, Gold efficiency, and price tag below $100, the PS-850SP looks appealing. 1st Player can keep pricing low because its mother company, Helly Technology, has a PSU manufacturing line. I have seen more and more Helly products lately, which isn't surprising since price to performance is good. This is a challenging field with big OEMs swatting smaller ones in almost every area. However, with the latter more versatile in design and sizable minimum order quantities usually not required, small and medium-sized brands do prefer smaller OEMs.

Back to the PS-850SP on hand. With a street price of $90, price per performance easily has the potential to go through the roof, making it a good deal for anyone after a strong PSU to power a high-end system. Going after high-end platforms is one approach, but achieving the highest-possible price-per-dollar ratio is much harder.

Specifications

1st Player Steampunk Gold 850W
Features & Specifications
Max. DC Output850 W
PFCActive PFC
Efficiency80 PLUS Gold, Cybenetics Gold (89–91%)
NoiseCybenetics Standard+ (35–40 dBA)
ModularYes (fully)
Intel C6/C7 Power State SupportYes
Operating Temperature0–40 °C
ProtectionsOver Voltage Protection
Under Voltage Protection
Over Power Protection
Over Temperature Protection
Over Current Protection
Short Circuit Protection
Cooling140mm sleeve bearing fan
(Yate Loon D14SH-12)
Semi-Passive OperationYes (selectable)
Dimensions (W x H x D)150 x 85 x 160 mm
Weight1.50 kg (3.31 lb)
ComplianceATX12V v2.52, and EPS 2.92
Warranty7 years
Price at Time of Review (excl. VAT)$89.99
1st Player Steampunk Gold 850W
Power Specifications
Rail3.3 V5 V12 V5 VSB-12 V
Max. Power20 A20 A70 A2.5 A0.3 A
100 W840 W12.5 W3.6 W
Total Max. Power850 W

Photos


The face of the box has a photo of the PSU with its fan grille exposed. Several icons describe the stand-out features, including the Gold efficiency badge. The maximum power output has been put in the bottom-right corner.


The bundle is rich, including Velcro straps and bags for the PSU and modular cables. Two leaflets are also provided, along with the fixing bolts to mount the PSU inside the case.


The fan grille has a unique, nonrestrictive design. The red switch at the face is for toggling the semi-passive operation on/off. 1st Player could have used a less striking color. Finally, the usual C14 AC receptacle is used, and there is a power switch.


There is not much to see on the sides. The power specifications label is on the bottom, and it is easily understood.


The modular panel has nine sockets.


Measuring 160 mm deep, dimensions follow the norm, which has it fit inside all ATX-compatible PC cases.

Cables and Connectors

Modular Cables
DescriptionCable CountConnector Count (Total)GaugeIn-Cable Capacitors
ATX connector 20+4 pin (600 mm)1118–22AWGNo
4+4 pin EPS12V (600 mm)2218AWGNo
6+2 pin PCIe (500 mm+150 mm)2418AWGNo
SATA (450 mm+150 mm+150 mm)2618AWGNo
4-pin Molex (450 mm+150 mm+150 mm)2418AWGNo
AC Power Cord (1400 mm) - C13 coupler1118AWGNo


The ATX cable is long enough, but the EPS cables should be around 50 mm longer. You probably won't have a problem with the 600 mm on offer if going with a regular-sized PC case, though.


The peripheral connectors are adequately far apart.

Component Analysis

Before reading this page, we strongly suggest looking at this article, which will help you better understand the insides of a PSU.

1st Player Steampunk Gold 850 W Parts Description
General Data
Manufacturer (OEM)Helly Technology
PCB TypeDouble-Sided
Primary Side
Transient Filter4x Y caps, 3x X caps, 2x CM chokes, and 1x MOV
Bridge Rectifier(s)2x
Inrush Current ProtectionNTC Thermistor (MF72-10D15) (10 ohm) & Relay
APFC MOSFETs2x Oriental Semiconductor OSG55R140FF (550 V, 14.5 A @ 100 °C, Rds (on): 0.14 ohm)
APFC Boost Diode1x Basic Semiconductor B1D08065K (650 V, 9.5 A @ 150 °C)
Bulk Cap(s)1x Nichicon (400 V, 680 uF, 2,000 h @ 105 °C, GL)
Main Switchers2x SI24N50F
APFC ControllerChampion CM6502UHHX
Switching ControllerChampion CM6901X
TopologyPrimary Side: APFC, half-bridge & LC converter
Secondary Side: synchronous rectification & DC-DC converters
Secondary Side
+12 V MOSFETs4x NCE Power NCEP40T20A (40 V, 150 A @ 100 °C, Rds (on): 1.6 mOhm)
+5 V & +3.3 VDC-DC Converters:
2x Excelliance MOS EMB03N03HR (30 V, 45 A @ 100 °C, Rds (on): 3 mOhm)
2x Excelliance MOS EMB06N03HR (30 V, 45 A @ 100 °C, Rds (on): 6 mOhm)
PWM Controller(s): 2xANPEC APW7073
Filtering Capacitors

Electrolytic:
3x Nippon Chemi-Con (1–5,000 h @ 105 °C, KZE)
3x Rubycon (3–6,000 h @ 105 °C, YXG
1x Rubycon (6–10,000 h @ 105 °C, ZLJ)

Polymer: 31x

Supervisor ICWeltrend WT7527V (OCP, OVP, UVP, SCP, PG)
Fan ModelYate Loon D14SH -12 (140 mm, 12 V, 0.70 A, sleeve bearing fan)
5VSB Circuit
Rectifier(s)1x 45R20S SBR
Standby PWM ControllerExcelliance MOS Corp EM8569C


This platform is by Helly, and 1st Player is its retail brand. The design is clean, without wires blocking airflow, and there is sufficient space between parts. The heatsinks are not large, especially on the secondary side. Lastly, soldering quality is good, and with the exception of the cooling fan, the parts Helly used are of high quality. I am not a big fan of Yate Loon. A Globe Fan or Hong Hua fan would have been a much better choice despite the increase in cost.


The transient filter starts on the AC receptacle with two Y caps and a single X caps and continues on the main PCB with the other parts.


Two Metal Oxide Varistors (MOV) handle voltage surges, while an NTC thermistor suppresses large inrush currents. A bypass relay supports the latter.


The bridge rectifiers are bolted together to a dedicated heatsink.


The APFC converter uses two Vishay FETs and a single CREE boost diode. The bulk caps are by Rubycon and have a combined capacity of 660uF.


The APFC controller is a Champion CM6502UHHX.


The two main switching FETs are installed in a half-bridge topology, and an LLC resonant converter is used for higher efficiency. The resonant controller is a Champion CM6901X.


The PSU's main transformer.


Four NCE Power FETs regulate the +12 V rail.


The electrolytic filtering caps are of good quality, and the same goes for the polymer caps.


Two DC-DC converters generate the minor rails. They use four FETs and two ANPEC APW7073 PWM controllers.


The standby PWM controller is an Excelliance MOS Corp EM8569C.


The supervisor IC is a Weltrend WT7527V.


The modular PCB is equipped with polymer caps for better ripple suppression.


Soldering quality is good.


The cooling fan is by Yate Loon and uses a sleeve bearing. This is not a good combination, especially as the PSU has a seven-year warranty.

Test Setup



Our Patreon Silver Supporters can read articles in single-page format.
Nov 20th, 2026 12:51 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts