be quiet! Dark Power 14 850 W ATX 3.1 Review 5

be quiet! Dark Power 14 850 W ATX 3.1 Review

Value & Conclusion »

Result Summary

Full-Range Load Testing (230 V)
All-rail
Load
12 V5 V3.3 VPower
(DC/AC)
EfficiencyFan
Speed
Noise
Level
Power
Factor
0 %0 A0 A0 A0 WN/AFan Stop0.11
12.05 V5.06 V3.31 V2.8 W
5 %2.90 A0.85 A0.85 A42.60 W84.21 %Fan Stop0.87
12.05 V5.06 V3.31 V50.59 W
10 %5.31 A2.02 A2.05 A85.50 W89.92 %Fan Stop0.93
12.04 V5.05 V3.31 V95.08 W
20 %11.60 A3.02 A3.05 A170.50 W93.25 %Fan Stop0.97
12.04 V5.05 V3.31 V182.84 W
30 %18.25 A3.52 A3.55 A255.80 W94.12 %Fan Stop0.98
12.03 V5.05 V3.31 V271.78 W
40 %24.90 A4.02 A4.05 A341.10 W94.25 %Fan Stop0.99
12.03 V5.05 V3.31 V361.91 W
50 %31.20 A5.02 A5.05 A426.20 W93.95 %Fan Stop0.99
12.02 V5.05 V3.31 V453.64 W
60 %37.50 A6.02 A6.05 A510.50 W93.35 %472 RPM26.6 dBA0.99
12.02 V5.05 V3.30 V546.86 W
70 %43.85 A7.02 A7.05 A596.20 W92.80 %485 RPM26.7 dBA0.99
12.01 V5.05 V3.30 V642.45 W
80 %50.20 A8.02 A8.05 A681.50 W92.25 %665 RPM29.8 dBA0.99
12.00 V5.05 V3.30 V738.75 W
90 %56.95 A8.52 A8.55 A767.10 W91.68 %965 RPM30.5 dBA0.99
12.00 V5.05 V3.30 V836.71 W
100 %63.45 A9.02 A9.15 A852.20 W91.12 %1272 RPM38.5 dBA0.99
11.99 V5.05 V3.30 V935.25 W


The PFC is working exceptionally well here, as is the voltage regulation, with negligible v-drop even at high loads.

The fan came on gently at 60% load and remained barely audible even at 100% load.

Efficiency



Rated Efficiency Validation (230 V)
Certification: 80 Plus Titanium
Test LoadRequiredMeasuredMarginStatus
10%90.00 %89.92 %-0.08 %Fail
20%93.00 %93.25 %+0.25 %Pass
50%95.00 %93.95 %-1.05 %Fail
100%91.00 %91.12 %+0.12 %Pass

EFFICIENCY TABLE uses 230 V EU Titanium spec (10/20/50/100% required 90/93/95/91%, per 80 Plus). 10% misses by 0.08% and 50% by 1.05%; 20% and 100% pass. Review text already notes the 50% dip. Reconcile before publishing.

Voltage Regulation

Voltage Regulation
Test Load+12 V+5 V+3.3 VStatus
5 %+0.42%+1.2%+0.3%Pass
10 %+0.33%+1.0%+0.3%Pass
20 %+0.33%+1.0%+0.3%Pass
30 %+0.25%+1.0%+0.3%Pass
40 %+0.25%+1.0%+0.3%Pass
50 %+0.17%+1.0%+0.3%Pass
60 %+0.17%+1.0%+0.0%Pass
70 %+0.08%+1.0%+0.0%Pass
80 %+0.00%+1.0%+0.0%Pass
90 %+0.00%+1.0%+0.0%Pass
100%-0.08%+1.0%+0.0%Pass

The voltages for each rail actually measure a very tiny touch above their rating at low to medium loads, and by full load we are seeing dead on rated; excellent regulation even across the lower voltage rails, showing the internal feedback loop is working properly.

Ripple

Ideally you want the DC voltage delivered by your power supply to be a completely flat line when looking through an oscilloscope. However, due to the switching nature of the ATX power supply and the less than ideal real world behavior of all the components involved, we get very small fluctuations in the voltage that are ripple and noise. The ATX spec allows a ripple of up to 120 mV for the +12 V rail and 50 mV for the minor rails.

Ripple
Test Load12 V5 V3.3 VStatus
5 %24 mV21 mV21 mVPass
10 %24 mV21 mV22 mVPass
20 %24 mV22 mV22 mVPass
30 %25 mV22 mV22 mVPass
40 %27 mV24 mV23 mVPass
50 %26 mV21 mV22 mVPass
60 %24 mV22 mV22 mVPass
70 %25 mV23 mV23 mVPass
80 %25 mV22 mV22 mVPass
90 %26 mV24 mV23 mVPass
100%24 mV21 mV22 mVPass

The ripple is well within ATX spec, very much on the lower end of the scale, and doesn't worsen at all with load which is excellent to see.

No unusual patterns were observed during the testing.

Short Circuit Protection

Short circuit protection is one of the most fundamental and important protections for a power supply. If a short circuit is detected on any rails, the PSU should turn off and prevent damage to itself and other components.

Short Circuit Protection
+12 V railOperational
+5 V railOperational
+3.3 V railOperational

SCP was working as expected with the unit. Protection is latching, requiring the supply to be power cycled to reset.
Next Page »Value & Conclusion
View as single page
Nov 21st, 2026 05:09 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts