Introduction
Corsair is a US-based peripherals and hardware company founded in 1994. It is now one of the leading manufacturers for gaming gear, with a portfolio spanning nearly every component you could need: DRAM memory modules, flash SSDs, keyboards, mice, cases, cooling, and much more.
The MP700 Elite is Corsair's newest PCIe Gen 5 SSD. If you think you've heard "MP700" before, then you are right, Corsair is using this model number for all their Gen 5 drives so far—we've seen a "MP700 Pro," "Pro SE" and of course the plain "MP700." While all the older drives are based on Phison's E26, the most popular PCIe 5.0 SSD controller, the MP700 Elite is built using the Phison E31—not sure why they didn't pick a different number to clarify that.
With the E31, Phison has added a second, cost-optimized, controller to their Gen 5 lineup. It's specifically designed for cost-efficient solutions, while the flagship E26 continues to cater to high-performance needs. Gen 5 SSDs have been on the market for a bit over a year, and virtually all drives came with a Phison controller—the E26. The problem—they are expensive and consume a lot of power, which means large heatsinks—many with an active cooling fan—have to be used.
The E31 is designed to address that. It uses the 7 nm TSMC process, with a design focus on optimizing power. The controller is paired with Kioxia BiCS8 3D TLC NAND operating at 3600 MT/s. For cost reasons a DRAM cache chip is not included, but the controller will use up to 64 MB of main memory through the Host-Memory-Buffer (HMB) feature.
The Corsair MP700 Elite will be available with or without heatsink and comes in capacities of 1 TB ($150 / $160) and 2 TB ($260 / $270), so you're paying an extra $10 for the heatsink. The endurance is set to 600 TBW and 1200 TBW. Corsair offers a five-year warranty with the MP700 Elite.
| Specifications: Corsair MP700 Elite 2 TB SSD |
|---|
| Brand: | Corsair |
|---|
| Model: | CSSD-F2000GBMP700EHS CSSD-F2000GBMP700ENH (w/o heatsink) |
|---|
| Capacity: | 2000 GB (1863 GB usable) 48 GB additional overprovisioning |
|---|
| Controller: | Phison E31T |
|---|
| Flash: | Kioxia 218-Layer 3D TLC BiCS8 T2BIGB5A2V |
|---|
| DRAM: | N/A, but 64 MB HMB |
|---|
| Endurance: | 1200 TBW |
|---|
| Form Factor: | M.2 2280 |
|---|
| Interface: | PCIe Gen 5 x4, NVMe 2.0 |
|---|
| Device ID: | Corsair MP700 ELITE with Heatsink |
|---|
| Firmware: | EVFM00.0 |
|---|
| Warranty: | Five Years |
|---|
Price at Time of Review: | $270 / $130 per TB |
|---|
Packaging
The Drive
The drive is designed for the M.2 2280 form factor, which makes it 22 mm wide and 80 mm long.
PCI-Express 5.0 x4 is used as the host interface to the rest of the system, which doubles the theoretical bandwidth compared to PCIe 4.0 x4.
On the PCB you'll find the controller and two flash chips, a DRAM cache chip is not included.
Corsair's preinstalled heatsink looks good, I like the arrangement of the heatsink structure and the matte, slightly rough, surface of the cooler.
Four screws hold the cooler together.
The Corsair logo is definitely a nice touch.
Slightly larger thermal pads could have helped temperatures, but the difference won't be big.
On the other side a big thermal pad is used.
Chip Component Analysis
The Phison E31 is the company's second PCI-Express 5.0 controller. It supports a four-lane configuration and four flash channels, it's a cost-optimized DRAM-less design. The controller is produced using a 7 nm process at TSMC Taiwan.
The two flash chips are Kioxia 218-layer 3D TLC NAND. Each chip has a capacity of 1 TB.
Test Setup
Synthetic Testing
- Tests are run with a 20-second-long warm-up time (result recording starts at second 21).
- Between each test, the drive is left idle for 60 seconds, to allow it to flush and reorganize its internal data.
- All write requests contain random, incompressible data
- Disk cache is flushed between all tests
- During these tests, M.2 drives are tested with additional active fan-cooling, to ensure thermal throttling can't happen
Real-life Testing
- After initial configuration and installation, a disk image is created; it is used to test every drive
- Automated updates are disabled for the OS and all programs. This ensures that—for every review—each drive uses the same settings, without interference from previous testing
- Our disk image consumes around 700 GB—partitions are resized to fill all available space on the drive
- All drives are filled with random data to 85% of their capacity. This is intentional, to run the drive in realistic operating conditions—nobody uses a nearly-empty SSD in their system. It also puts additional stress on the pseudo-SLC cache subsystem, because there is less free NAND space to work with
- Partitions are aligned properly
- Disk cache is flushed between all tests
- In order to minimize random variation, each real-life performance test is run several times, with reboots between tests to minimize the impact of disk cache
- All application benchmarks run the actual application and do not replay any disk traces
- Our real-life testing data includes performance numbers for a typical high-performance HDD, using results from a Western Digital WD Black 1 TB 7200 RPM 3.5" SATA. HDDs are significantly slower than SSDs, which is why we're not putting the result in the chart, as that would break the scaling, making the SSDs indistinguishable in comparison. Instead, we've added the HDD performance numbers in the title of each test entry
- During these tests, M.2 drives are tested with additional active fan-cooling, to ensure thermal throttling can't happen