Introduction
Today, we are reviewing the Crucial MX300 SSD 525 GB in its M.2 variant. According to Crucial, the MX300 M.2 should be identical to the SATA version in terms of performance because it uses the SATA interface too. This is in contrast to high-end M.2 NVMe SSDs which use NVMe over PCIe. Being SATA, the same performance constraints as with 2.5 inch SATA apply, which means the storage interface can not exceed around 500 MB/s in speeds. Just like the other MX300 variants, this drive is built using Micron 3D TLC NAND, which is paired with a 4-channel 88SS1074 controller from Marvell.
In order to boost TLC chip performance to make up for the ground lost over MLC, Crucial designates a small, variably sized amount of memory as SLC cache, which writes a single bit to each TLC cell instead of three. While much faster, such a setup is basically a speed vs. size tradeoff. In terms of technology, the SLC cache is identical to that of the MX200 (not BX200).
The MX300 Series in an M.2 form factor is available in capacities of 275 GB, 525 GB, and 1 TB, whereas the 2.5" form factor drives additionally come in 750 GB and 2 TB variants.
| Specifications: Crucial MX300 M.2 525 GB |
|---|
| Brand: | Crucial |
|---|
| Model: | CT525MX300SSD4 |
|---|
| Controller: | Marvell 88SS1074 BSW2 |
|---|
| Flash: | Micron, 16 nm TLC MT29F3T08EUHBBM4-3R:B |
|---|
| Endurance: | 160 TB total bytes written |
|---|
| Form Factor: | M.2 2280 |
|---|
| Capacity: | 525 GB (489.1 GB usable) 38 GB additional overprovisioning |
|---|
| Interface: | SATA 6 Gbps |
|---|
| Device ID: | Crucial_CT525MX300SSD4 |
|---|
| Firmware: | M0CR060 |
|---|
| Warranty: | Three years |
|---|
Packaging and Contents
Inside the package, you will find the SSD, some screws, and an Acronis True Image download coupon.
The Drive
The drive uses the M.2 2280 form factor, which means it is 22 mm wide and 80 mm long. A heatspreader is not installed.
Note how the connector has two notches? These identify the drive as a SATA-based drive. So it is not using NVMe over PCIe like other high-end drives. This limits the transfer speeds to around 500 MB/s. You should be aware that you will "lose" one of the cabled SATA ports when connecting this drive. If your motherboard has six 2.5" SATA ports, for example, you will only have five of those active after installing an M.2 SATA SSD.
You will find the SSD controller and two flash chips on the PCB. A single DRAM chip is also present to provide the SSD controller with RAM and soak up write bursts.
The Marvel controller is a new variant with TLC flash support.
The two TLC flash chips are produced by Micron and are built on a 16 nanometer process.
Test Setup
| Test System SSD 2018.1 |
|---|
| CPU: | Intel Core i7-7700K 4.2 GHz (Kaby Lake, 8 MB Cache) |
|---|
| Motherboard: | MSI Z270 SLI Plus Intel Z270 |
|---|
| Memory: | 16 GB DDR4-3200 16-16-16-36 |
|---|
| Cooling: | CRYORIG C7 |
|---|
| Graphics: | Intel Integrated |
|---|
| Software: | Windows 10 64-bit Creators Update |
|---|