G-Wolves Fenrir Pro Review 15

G-Wolves Fenrir Pro Review

(15 Comments) »

Value and Conclusion

  • The G-Wolves Fenrir Pro is available for $159.00.
  • True 8000 Hz polling
  • Ultra-low click latency
  • Excellent sensor performance
  • Very high button quality
  • Very good scroll wheel
  • Good choice of components
  • Lightweight
  • Nicely gliding mouse feet
  • Full software customizability
  • Sets of replacement feet included
  • Set of grip tape included
  • Pricey
  • Included cables are too short and too stiff
  • Web driver not available as standalone app
G-Wolves mice already cater primarily to enthusiasts by virtue of their pricing and puristic approach. Part of this approach is offering mice designed specifically for certain grip styles, such as fingertip grip, as well as offering "Pro" variants of existing releases that take things even further. Within this constellation, the Fenrir Pro occupies a peculiar spot: at 23 and 21 g, respectively, the Fenrir Max and Asym already are exceptionally light, leaving little room for improvement on the Fenrir Pro, especially if one doesn't want to embark on the lazy route of dropping battery capacity, which G-Wolves do not. At 20 g, the Fenrir Pro indeed manages to be marginally lighter than the Asym. Much like on the Hati-S2 Pro 8K, this weight reduction is achieved by doing away with the concept of a bottom shell altogether. Rather, the PCB is screwed directly to the top shell, and some additional weight is saved on the material itself, as the sides don't extend all the way to the bottom, leaving little gaps. Other than that, the design is identical to the Asym or Max, with the extended PCB providing great structural integrity: there is no rattle when shaking, no creaking or flexing of the shell when applying lateral pressure, and actuating the side buttons by pressing below them cannot be done regardless of force.

In terms of shape, the Fenrir Pro is essentially a "best of" of the Fenrir Max and Asym. The general frame is the same as on the Asym, as height, front width, and grip width are a match, and button height as well as the overall profile likewise are shared. The appendage at the back of the Pro has no meaningful impact on how the mouse is held, and without it, its length is the same as on the Max and Asym. However, the Fenrir Pro features the same symmetrically shaped sides as the Max, resulting in a narrower back width compared to the Asym. While the side buttons are at the same absolute height as on the Fenrir Pro, they sit lower relatively to the bottom of the shell, which as mentioned doesn't extend all the way down. Accordingly, even when coming from the Asym, the Fenrir Pro may take some getting used to in terms of thumb placement, as instead of in the middle of the side, one has to place it lower and partially "off the shell" to avoid hitting the side buttons accidentally.

Unlike the recent HTM Plus and HTX Ultra, the Fenrir Pro does not utilize SPDT Huano switches to employ the NC pin for lower physical click latency, for the simple reason that these switches are too tall to fit. Rather, the same surface-mounted Omron D2LS-21 (20 M) switches already familiar from the Fenrir Asym see use, albeit combined with a refined button design. Unlike the Asym, the Fenrir Pro has small hinges at the front, which restrict vertical motion, and with good success: pre-travel is low and post-travel very low, resulting in a firm and snappy button response. Lateral button movement can be provoked to a low degree. The side buttons too are outfitted with surface-mounted Omron D2LS-21 switches, albeit of a lower rating. Pre- and post-travel are very low on these, and the actuation point is even across their entirety. For the scroll wheel, G-Wolves once again has opted for a TTC encoder, albeit of a different type (black), whose 4.5 mm size is necessitated by the lower profile. Of note is that this encoder can be difficult to replace, both due to its size and non-standard pin distance. In addition, the scroll wheel isn't fully inserted into the encoder, which is done on purpose, as otherwise the axle wouldn't fully reach the scroll wheel switch. Tactility is good on this one, with clearly defined steps allowing for controlled scrolling, and noise levels remain largely under control as well. Much like on previous G-Wolves releases, the bottom (what little there is) lacks indents for feet, allowing one to apply feet of non-default sizes and shapes. Aside from the feet installed by default, two sets of dot feet are included with the mouse. They're all made of pure PTFE, and glide very well. Of note is that due to the lack of a bottom, the Fenrir Pro lacks a sensor ring entirely, which isn't necessarily an issue, but having one would probably be better for users of soft mats in particular.

The Fenrir Pro combines PixArt's PAW3950 sensor with the latest Nordic nRF54L15 MCU. The biggest benefit brought by the 54 series MCUs from Nordic is lower power draw, resulting in far improved battery life. To enable polling rates of above 1000 Hz not just in wireless, but in wired operation as well, the Fenrir Pro furthermore comes with a USB high-speed MCU on the mouse PCBA, too. In terms of performance, the Fenrir Pro does admirably. CPI deviation is a bit higher than I'd like it to be at -3.1%, though easily corrected still. Unlike on recent G-Wolves mice using the older nRF52840 chipset, polling stability is flawless on the Fenrir Pro, with no polls being missed at any polling rate, be it wired or wireless, and the target interval is averaged on the dot throughout. An interesting and somewhat peculiar difference exists when compared to previous nRF52840 mice from G-Wolves, however. On those, motion delay was the same regardless of polling rate, provided that sensor run mode had been set to corded. On the Fenrir Pro, on the other hand, the lowest motion delay indeed is only achieved at 8000 Hz, with lower polling rates scaling accordingly. In wired operation at 8000 Hz, the Fenrir Pro attains a lead of 1.2 ms over the G403 (control subject) without MotionSync, and a lead of 1.0 ms without MotionSync in wireless operation at 8000 Hz, placing the Fenrir Pro in the upper echelon in terms of latency. The "competitive mode" toggle works identically to previous G-Wolves releases. When enabled, it sets sensor run mode to corded and the sensor framerate to its maximum value, prioritizing performance over battery life. At polling rates of 2000 Hz and higher, corded mode is already enabled by default, which is why only sensor framerate is set to its maximum value. Click latency likewise scales with polling rate in wireless operation, albeit in a less progressive fashion: at 2000, 4000, and 8000 Hz, a rounded average of 0.3 ms is achieved when using the lowest debounce time value, with 1000 Hz trailing slightly behind at 0.5 ms. Since a flawlessly implemented slam-clicking prevention algorithm is present, there is no reason not to set debounce time to 0 ms, unless any double-clicking emerges over time.

G-Wolves does not cite any battery life numbers. The software features a percentage-based battery life indicator using single-digit increments, which isn't particularly reliable or accurate, but at least sufficiently so to allow giving a rough estimate. For every two hours of usage at 8000 Hz with competitive mode enabled, the indicator went down by a bit more than 10%, suggesting an expected battery life of a bit less 20 hours at 8000 Hz, and presumably in the range of 90 hours at 1000 Hz. Accordingly, compared to previous nRF52840-equipped G-Wolves releases, the Nordic 54 series MCU used on the G-Wolves indeed improves battery life greatly, all while using just a 200 mAh capacity battery. Charging isn't all that speedy on the Fenrir Pro, but decent enough, though playing while charging won't be an option with the included cables anyway. The first one isn't all that flexible to begin with, but more importantly seriously short at 1.25 m, whereas the second one is a bit longer at 1.45 m and stiff as well. As such, it is best to keep the Fenrir Pro charged at all times to minimize forced downtime.

As with other recent G-Wolves releases, configuration on the Fenrir Pro is done through a web driver. Due to using WebHID, this will only work in Chromium-based browsers such as Chromium or Edge. Hence, for those not already using these browsers, being directed towards a web driver requires installing an additional browser, which of course comes with its own resource footprint, much like standalone peripheral software would. In addition, if G-Wolves were to go defunct, or decide to no longer host the web driver, configuration would become impossible, as a local copy unfortunately won't work. This is doubly problematic in that the Fenrir Pro doesn't even have a CPI button, so even something basic as changing CPI requires using software. As such, I consider the exclusive web driver a step back compared to the previous standalone application featured with earlier G-Wolves mice, and would welcome if G-Wolves would also release a desktop version of their web driver in the future. As for the driver itself, I couldn't find any bugs, and all the relevant options are present. The issue where setting changes could still be made after the mouse has entered sleep mode has been addressed, and the only remaining oddity is that any adjustment to the debounce settings will only take effect after the mouse has been lifted and reset once.

At $159.00, the Fenrir Pro is priced identically to the Fenrir Max and Asym. Accordingly, one could make an argument that there is little reason to pick the Asym over the Pro—after all, the Nordic 54 series MCU grants the Pro a clear edge in terms of battery life, 8000 Hz wired polling likewise is exclusive to the Pro, and the shape is barely different, too. For anyone coming from the Fenrir Asym, there is little reason to pick up the Pro, but those undecided between the Asym and Pro may in fact be better off going with the latter right away. In any case, the Fenrir Pro is, if anything, an improvement on the Max and Asym, and accordingly earns our Recommended award, coupled with our likewise well-earned Expensive badge.
Recommended
But Expensive
Discuss(15 Comments)
View as single page
Nov 22nd, 2026 17:28 CST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts