G-Wolves Hati-S2 Pro 8K Review 1

G-Wolves Hati-S2 Pro 8K Review

(1 Comment) »

Value and Conclusion

  • The G-Wolves Hati-S2 Pro 8K is available for $159.00.
  • True 8000 Hz wireless polling
  • Very low click latency
  • Very good sensor performance
  • High button quality
  • Good scroll wheel
  • Good choice of components
  • Lightweight
  • Nicely gliding mouse feet
  • Full software customizability
  • Sets of replacement feet included
  • Set of grip tape included
  • Pricey
  • Minor polling instability
  • CPI deviation
  • Included cables are either too short or too stiff
  • Web driver not available as standalone app
While G-Wolves mice already cater to enthusiasts, some do more than others, and the Pro series mice definitely fall into the "more" category. Compared to the non-Pro variant, the Hati-S2 Pro 8K is both smaller and lighter, the latter of which is of particular note, given how the structure of the non-Pro already had been meticulously optimized for weight. Despite this, G-Wolves managed to shave off another 5 g without compromising on battery capacity (which would be a quick yet painfully dull solution) or structural rigidity. For the Hati-S2 Pro 8K, G-Wolves essentially has done away with the very concept of a bottom shell, as the top shell merely has some edges at the bottom to stick the feet to, and all PCBs are screwed directly to the top shell. In addition, hexagonal holes are scattered across the top shell, leaving only the upper portion of the main buttons solid. What prevents this construction from crumbling to pieces upon physical contact is once again the PCB, which has been extended such that it supports the shell. Most remarkably, structural rigidity is indeed excellent, as there is no rattle when shaking, no creaking or flexing of the shell when applying lateral pressure, and actuating the side buttons by pressing below them is impossible regardless of force. In short, the Hati-S2 Pro 8K is yet another impressive engineering feat from G-Wolves, and one that demonstrates what is possible with trusty old ABS plastic.

Marginal weight savings also come from the fact that the Hati-S2 Pro 8K is slightly shorter than the non-Pro, whereas the other dimensions have been retained. The Hati-S2 8K already was a shorter Hati-S, which is why the length reduction of the Hati-S2 Pro 8K brings it closer to actual fingertip grip mice. As such, the Hati-S2 Pro 8K sits at that peculiar juncture between claw and fingertip grip, where it is short enough to be used by claw and fingertip grippers alike, though the latter group still may find the rather pronounced hump distracting.

In terms of switches, the Hati-S2 Pro 8K also switches things around a bit. The main button switches once again come from Huano, but this time around, they are of the green transparent shell, white plunger variety. The main differences to the blue transparent shell, pink plunger variety are twofold: the former have a higher rating (100 instead of 80 million) and are rated for a lower actuation force, resulting in accordingly lighter actuation. In practice, these indeed feel lighter, though still retain a similar degree of snappiness, which is at least partially owed to low pre- and very low post-travel as well, which is accompanied by a low degree of lateral button movement. The side buttons are outfitted with 2-pin, low-profile switches from TTC (brown shell, blue plunger). While the forward side button has low pre- and post-travel, the back side button doesn't fare as well, as pre-travel is moderate, and post-travel high to where the button can be pushed into the shell in its entirety, though the actuation point is still mostly even. For the scroll wheel, G-Wolves once again has opted for the TTC blue/yellow core encoder, albeit in the 9 mm size. Tactility is great on this one, with very clearly defined steps allowing for controlled scrolling, and noise levels are appreciably low. Much like on previous G-Wolves releases, the bottom (what little there is) lacks indents for feet, allowing one to apply feet of non-default sizes and shapes. Aside from the feet installed by default, two sets of larger feet are included with the mouse, along with three sets of dots. They're all made of pure PTFE, and glide very well. Of note is that due to the lack of a bottom, the Hati-S2 Pro 8K lacks a sensor ring entirely, which isn't necessarily an issue, but having one would probably be better for users of soft mats in particular.

The Hati-S2 Pro 8K combines PixArt's latest PAW3950 sensor with a Nordic nRF52840 MCU. Compared to the previous 01.00.37 firmware, the latest 01.00.39 firmware introduces a novelty on G-Wolves mice, which is the so-called competitive mode. When enabled, this sets sensor run mode to corded, which prioritizes performance over battery life. At polling rates of 2000 Hz and higher, corded mode is already enabled by default and the setting accordingly does nothing, but at 1000 Hz and under, enabling corded mode essentially brings motion delay in line with polling rates of 2000 Hz and over. As such, this is a worthwhile setting, as it allows one to enjoy the lower motion delay brought by 2000 Hz and over without suffering the potential FPS hit induced by them. Click latency is the same across all polling rates anyway, so the only benefit polling rates of 2000 Hz and above have over polling rates of 1000 Hz and under with competitive mode enabled is higher positional accuracy, along with increased smoothness due to more frequent updates.

In terms of numbers, virtually nothing has changed compared to the 01.00.37 firmware. CPI deviation sits at +6.9%, which is easily corrected, but on a level where correction is definitely needed, and therefore not ideal. Polling stability continues to be a mixed bag. At and below 1000 Hz, polling is generally stable, although occasionally, longer sequences of off-period polls show up. Both 2000 and 4000 Hz show elevated variance, though 4000 Hz also suffers from off-period polls. On the other hand, 8000 Hz is perfectly stable, which is notable in that motion delay is the same across 2000, 4000, and 8000 Hz, as the Hati-S2 Pro 8K enjoys a lead of 0.8 ms over the Logitech G403 (control subject) without MotionSync. Since a PAW3950 is used, the target interval of 125 us is maintained at 8000 Hz even with MotionSync enabled. At 1000 Hz, this lead shrinks to just 0.4 ms, though as mentioned earlier, 0.8 ms too can be reached at 1000 Hz by enabling competitive mode. The Hati-S2 Pro 8K averages a click latency of 0.4 ms at the lowest debounce time setting across all polling rates, and since a flawlessly implemented slam-click prevention algorithm is present, there is no reason not to use 0 ms as long as no double-clicking emerges.

G-Wolves does not cite any battery life numbers. That said, given that 80 hours were cited for the Hati-S Ultra at 1000 Hz, which used a 250 mAh battery, it is fair to assume that the Hati-S2 Pro 8K lands on a similar level, since a 250 mAh battery is utilized for this one, too. Unfortunately, the percent-based battery life indicator still isn't much help in this regard, as it is simply not reliable enough to gauge anything. Charging isn't all that speedy on the Hati-S2 Pro 8K, but decent enough, though playing while charging won't be an option with the included cables anyway. The first one isn't all that flexible to begin with, but more importantly seriously short at 1.25 m, whereas the second one is a bit longer at 1.45 m yet even stiffer. As such, it is best to keep the Hati-S2 Pro 8K charged at all times to minimize forced downtime.

As with other recent G-Wolves releases, configuration on the Hati-S2 Pro 8K is done through a web driver. Due to using WebHID, this will only work in Chromium-based browsers such as Chromium or Edge. Hence, for those not already using these browsers, being directed towards a web driver requires installing an additional browser, which of course comes with its own resource footprint, much like standalone peripheral software would. In addition, if G-Wolves were to go defunct, or decide to no longer host the web driver, configuration would become impossible, as a local copy unfortunately won't work. This is doubly problematic in that the Hati-S2 Pro 8K doesn't even have a CPI button, so even something basic as changing CPI requires using software. As such, I consider the exclusive web driver a step back compared to the previous standalone application featured with earlier G-Wolves mice, and would welcome if G-Wolves would also release a desktop version of their web driver in the future. As for the driver itself, I couldn't find any bugs, and all the relevant options are present. The issue where setting changes could still be made after the mouse has entered sleep mode has been addressed, and the only remaining oddity is that any adjustment to the debounce settings will only take effect after the mouse has been lifted and reset once.

At $159.00, the Hati-S2 Pro 8K is priced $20 higher than the Hati-S2 8K. Frankly, I'm of the opinion that for most people, paying this premium isn't worth it, as performance on equivalent firmware is the same, the weight difference of 5 g not that meaningful, and the Hati-S2 8K a fine enough mouse as it is. At the same time, a Pro series is, by definition, not for everyone, which is why there is little point in holding this against the Hati-S2 Pro 8K. For those who do value every gram, and are willing to pay a little extra for the engineering efforts required to get there, the Hati-S2 Pro 8K is a worthwhile release, and accordingly earns our Recommended awards, along with the equally well-earned Expensive badge.
Recommended
But Expensive
Discuss(1 Comment)
View as single page
Nov 20th, 2026 15:29 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts