PowerColor ALPHYN AM10 Review 4

PowerColor ALPHYN AM10 Review

Sensor & Performance »

Build Quality

Overall build quality is very solid. There is no rattle when shaking the mouse. When applying lateral pressure, no creaking or flexing of the shell can be observed. Activating the side buttons by squeezing the sides is impossible. Lastly, accidental clicks when slamming down the mouse do occur.

Buttons


Main buttons on the ALPHYN AM10 are good. Both pre- and post-travel are moderate, resulting in a firm and snappy button response nonetheless. Being visually separated from the shell, button movement is moderate (right button) to large (left button) when provoked. Button stiffness is medium. A pair of Omron D2FP-FN2 (China) switches are used.


Side buttons are very good (forward button) to decent (back button). Whereas the forward button has low pre- and post-travel, post-travel is bordering on high on the back button, and the actuation point is not even, resulting in mushy actuation. Button size and placement are good, as actuation is possible easily by rolling one's thumb across. A set of Kailh switches (black plunger) are used for these.

At the top of the mouse is a button for cycling through the set CPI levels, which works just fine. A Huano switch (white plunger) is used for this one. A slider at the bottom switches between 2.4 GHz wireless, Bluetooth, and off-state, which also works fine, along with a button for pairing the mouse. A seemingly unbranded tactile switch is used for this one.

Scroll Wheel


The scroll wheel is very good. Noise levels are under control, and tactility is good, as the individual steps are clearly distinct. While I'm unable to identify the exact type, it appears to come from TTC (white or "silver") and has a height of 5 mm. The middle (scroll wheel) click requires medium to high force for actuation. A seemingly unbranded tactile switch (white plunger) is used for this one.

Surface

The ALPHYN AM10 has a matte surface all over. Grip is fine, and it doesn't attract fingerprints or dirt too much. It is fairly easy to clean, and there are no signs of wear left after doing so. All in all, very good materials.

Button Sound Test


Disassembly


Disassembling the ALPHYN AM10 is fairly easy. After removing all skates and the screws beneath them, bottom and top shell can be separated by applying lateral pressure to the rear, from which point on dislodging the clips at the sides can be done with ease. Caution needs to be applied when separating the top and bottom shell to avoid ripping the cable connecting the two.

The internal design is largely inefficient. The battery is stuck to a plastic assembly erected above the main PCB. The top and side-button switches sit on their own PCB screwed to the top shell and connected through a ribbon cable to the main PCB. From this PCB, another ribbon cable goes to a PCB holding two LEDs for illumination. Another PCB holding an LED branches off the main PCB, providing scroll wheel illumination. The scroll wheel is suspended in a half-enclosure, which can press down on the scroll wheel switch located on the main PCB. Counting the screws used for the battery holder as well, three screws are used to affix the moderately thick and oversized main PCB to the bottom. Two rear-mounted MCUs are present: an NXP LPC5516, which provides a USB High-Speed PHY and whose datasheet can be found here, and a Nordic nRF52832, which handles wireless communication and whose datasheet can be found here. Interestingly, the ALPHYN AM10 nominally only supports Bluetooth 5.2, despite the nRF52832 supporting Bluetooth 5.4. The production date for the main and side-button PCBs is the 44th week of 2024, whereas the PCBs holding LEDs were manufactured during the 45th week of 2024.


As for the soldering and general quality of the PCB, I'm unable to find any noteworthy flaws.
Next Page »Sensor & Performance
View as single page
Nov 21st, 2026 06:36 PST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts