Introduction
Zhitai (致钛) is the consumer memory and storage brand of YMTC (Yangtze Memory Technologies), China's largest and most advanced maker of 3D NAND flash. Founded in 2016 and headquartered in Wuhan, YMTC is the company that put Chinese-made NAND on the map: it designs and fabricates its own flash wafers in-house, rather than sourcing them from established players like Samsung, SK hynix, Micron and Kioxia. That makes the TiPlus 9100 one of the few drives on the market where both the brand and the NAND flash inside come from the very same company. It's also a DRAM-less design, which makes a lot of sense right now, with DRAM prices having gone through the roof.
Since this is my first review of a Zhitai drive, I did a bit of digging into the name. In Chinese, it's written 致钛: the first character, 致, roughly means "to deliver" or "to achieve," and the second, 钛, means "titanium"—so the brand is reaching for that titanium visual image—strength, resilience, and premium engineering. This is a China-first brand, and the name was clearly picked to work well in Mandarin rather than English. The international spelling, with its "zh," will be so unfamiliar to most that they'll probably just settle on "zhee-tie"—not unlike how Huawei constantly gets mispronounced. If you'd like to get closer, try the following: picture Jar Jar Binks (yes, I've got Star Wars references for you). Take one "Jar," drop the "a," and you're left with "Jr," then imagine him sitting in a TIE Fighter. That "r" curls your tongue back the same way the Mandarin zh sound does, so "Jr-tie" is pretty close.
Personally, I think "YMTC" is a great name, which rolls off the tongue far more easily—but I suspect they wanted to separate the flash-manufacturing side of the business, while Zhitai is the consumer-oriented name on the retail drives.
YMTC's signature innovation is the Xtacking architecture. Any flash chip has two main parts: the memory cells that store your data, and the control logic that runs them. Normally both are built together on the same piece of silicon, but Xtacking builds them on two separate wafers and then bonds the two whole wafers together with millions of tiny vertical connections. Making each part on its own lets YMTC optimize both, reach higher speeds, and bring new generations to market faster. The pace has been impressive: in just a few years the company went from 64-layer NAND to 128-layer (Xtacking 2.0), 232-layer (Xtacking 3.0), and now the 267-layer Xtacking 4.0 that powers the TiPlus 9100—it's the YMTC X4-9070 3D TLC NAND.
Zhitai doesn't officially specify which controller drives that flash (I asked), but my own analysis strongly suggests that it is a Maxio MAP1802. That's a modern DRAM-less PCIe Gen 5 design fabricated on TSMC 6 nanometer. This combination positions the TiPlus 9100 as an affordable, mainstream model with Gen 5 performance—offering high sequential speeds without the price premium of a DRAM-equipped solid-state-drive. The TiPlus 9100 is offered in 1 TB, 2 TB and 4 TB capacities, with endurance rated at 600 TBW, 1200 TBW and 2400 TBW respectively; we're reviewing the 1 TB model today, which carries a five-year warranty. As a China-first brand it isn't broadly available internationally yet, so pricing comes from the domestic market: at the time of writing, JD.com lists it at 1319 RMB for our 1 TB unit, 2099 RMB for the 2 TB, and 4399 RMB for the 4 TB. These Chinese retail prices include 13% VAT; with that removed—to line up with how US prices are usually quoted—the three capacities work out to roughly $160, $260 and $540, respectively.
| Specifications: Zhitai TiPlus 9100 1 TB SSD |
|---|
| Brand: | Zhitai |
|---|
| Model: | TiPlus 9100 / ZTSS3CB08D6CMC |
|---|
| Capacity: | 1024 GB (953 GB usable) |
|---|
| Controller: | Maxio MAP1802 Rebranded as PK2123-1AC AAT2A672312 |
|---|
| Flash: | TLC, YMTC 267-layer, X4-9070 ZTN0ATF1B3HCBE |
|---|
| DRAM: | N/A, but 64 MB HMB |
|---|
| Endurance: | 600 TBW |
|---|
| Form Factor: | M.2 2280 |
|---|
| Interface: | PCIe Gen 5 x4, NVMe 2.0 |
|---|
| Device ID: | ZHITAI TiPlus9100 1TB |
|---|
| Firmware: | ZTA32001 |
|---|
| Warranty: | Five Years |
|---|
Price at Time of Review: | $160 / $160 per TB |
|---|
The Drive
The drive is designed for the M.2 2280 form factor, which makes it 22 mm wide and 80 mm long.
PCI-Express 5.0 x4 is used as the host interface to the rest of the system, which doubles the theoretical bandwidth compared to PCIe 4.0 x4.
On the PCB you'll find the controller and two flash chips. There is no DRAM cache, the drive uses HMB instead.
The sticker on the drive is really just a paper sticker (no copper core or similar conductor), so it doesn't assist with managing thermals.
Chip Component Analysis
The controller on this drive is a Maxio MAP1802, a cost-optimized PCI-Express Gen 5 controller manufactured on TSMC's 6 nm process. It runs four Arm Cortex-R8 cores and connects to the NAND flash over four channels at 3600 MT/s. MAP1802 is a DRAM-less design that relies on Host Memory Buffer (HMB) instead of a dedicated DRAM chip, borrowing a small portion of system memory for its mapping tables, which helps keep both cost and power consumption down.
Interesting to note is that Zhitai has rebranded the controller—there are no visible markings on the package to indicate that it is a Maxio part, or even that it is the MAP1802. We identified it based on the IC package's style, shape and size, which match the MAP1802 exactly.
The two flash packages are YMTC 3D TLC NAND (X4-9070), built on the company's Xtacking 4.0 architecture with 267 layers. Each package has a capacity of 512 GB.
Test Setup
Synthetic Testing
- Tests are run with a 20-second-long warm-up time (result recording starts at second 21).
- Between each test, the drive is left idle for 60 seconds, to allow it to flush and reorganize its internal data.
- All write requests contain random, incompressible data.
- Disk cache is flushed between all tests.
- During these tests, M.2 drives are tested with additional active fan-cooling, to ensure thermal throttling can't happen.
Real-life Testing
- After initial configuration and installation, a disk image is created; it is used to test every drive.
- Automated updates are disabled for the OS and all programs. This ensures that—for every review—each drive uses the same settings, without interference from previous testing.
- Our disk image consumes around 1.5 TB—partitions are resized to fill all available space on the drive.
- All drives are filled with random data to 80% of their capacity. This is intentional, to run the drive in realistic operating conditions—nobody uses a nearly-empty SSD in their system. It also puts additional stress on the pseudo-SLC cache subsystem, because there is less free NAND space to work with.
- 1 TB drives are tested in three independent runs, applications first, then 2x games, each filled to 80% capacity, with secure erase between.
- Partitions are aligned properly.
- Disk cache is flushed between all tests.
- In order to minimize random variation, each real-life performance test is run several times, with reboots between tests to minimize the impact of disk cache.
- All application benchmarks run the actual application and do not replay any disk traces.
- During these tests, M.2 drives are running with additional active fan cooling, to entirely prevent thermal throttling.
Comparison Drives
We compare the tested drive to a wide selection of SSDs currently available on the market. Besides popular drives, our focus is also on including common controller and flash type combinations.