• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Why the f*ck not? - a bad ideas only build, by Mussels!

Updates!

I got the antec PSU back from a friend, it was rattly! Lets remove the sticker and put some lubricant in there...
MVIMG_20200720_174018.jpg

Oh. well lets try anyway, because thats the point of this thread

MVIMG_20200720_175038.jpg

Well, f*ck.
At this point i went to buy an 80mm fan for the PSU off facebook marketplace, but ended up with an entire haul of shit for just $20

Five Thermaltake RGB fans (missing some needed cables for their shitty controllers), DDR3 ram, GTX 780?!? two 80mm xigmatek fans and a xigmatek 115x cooler

115929041_900888417068488_971869042672495264_n.jpg


Swapped the fan over, PSU success! needs to be externally powered since the internal header cant run this fan at idle for some reason, so i switched to the facebook special

114585632_945955445919786_2184613302242434208_n.jpg


I spent 15 minutes jamming all that spaghetti in, wedging the PSU cover over the top and hearing a goddamn rattle. Ripped the ENTIRE THING APART AGAIN
MVIMG_20200720_205933.jpg



Mother. F*cking. Dust. Bunnies. Oh and bits of plastic. And some bark. Y'know, why the f*ck not?
MVIMG_20200720_211815.jpg


Put liquid metal on the GPU (you're catching on to my bad ideas now, aren't you?) and got some nice load temps (64C, hard to read sorry)
MVIMG_20200720_213151.jpg


And of course the obligatory wall power reading, being power hungry older gen hardware... honestly not too bad. With Vsync on, it'd be a lot less.
MVIMG_20200720_213903.jpg
 
all that fuckery, ended up with one beast of a system
MVIMG_20200720_225813.jpg
 
RGB alone would make me consider any system a disgrace but this, this is art

closed front panel aaaagh
 
Oh dont worry it came WITH a mesh front panel... but i swapped it
 
And why the ^%"6 not?? :D :D

Are you using it like this and setting it on fire with the WCG crunching or are you holding back for a little bit?? :D
I’m late to this, but that is the funniest build story I have seen!! :roll: Nice to see such dedication to the “because I can” build!
 
i've had 4 local people ask to buy the system and a 5th (my dad) wanting the same case and more RGB fans for his


I cant help but feel this is the best/worst system i've ever made
 
i've had 4 local people ask to buy the system and a 5th (my dad) wanting the same case and more RGB fans for his


I cant help but feel this is the best/worst system i've ever made
Such thread is full of awesome. I love it :D :D
 
Oh my... Swap it back!

Don't tell him what to do!

Mussels, I demand a video of yourself somehow burning your house down as a result of this, and screaming "FREEDOM!"

Oops, I just told you what to do. Sorry. Be free, freeloader.
 
i've had 4 local people ask to buy the system and a 5th (my dad) wanting the same case and more RGB fans for his


I cant help but feel this is the best/worst system i've ever made
Ahaha, when I was doing builds for people, some of those people REALLY tempted me to give them something like this, just because it's basically what they asked for and they didn't like me explaining why it might not be what they want in the end.

But no... I had to be nice and talk them down from it. I'm not strong like you... I can't build on that level. I can think of one person in particular who would definitely buy this off of you if I offered it to him. I will never do another build for him again. Though if I do, maybe we can work something out... with your skills and all. I never would've thought to swap-out the mesh. You're a revolutionary among mollusks.
 
Next bad idea: LAP THAT BITCH

I used half the clamshell packaging to make it a ton easier to do
p1kalmig2k719.jpg


Lapped, installed, f*ck i'm out of thermal paste... used the dregs of a years old tube i found until new stuff arrives in the mail
MVIMG_20200722_163355.jpg


Oh and OF COURSE A PIN SNAPPED OFF AND STAYED IN THE SOCKET

(its not as dirty as it looks, that was dust/debris from the sanding)
zp5tm1qbi6081.jpg

92c31apgjk738.jpg
 
You're really not having much luck with this are you @Mussels ? :(
 
Oh and OF COURSE A PIN SNAPPED OFF AND STAYED IN THE SOCKET
man you have special perk for this!
i've used only socketed cpus since my very first pc in 486 era and i had cpus pulled out of the socket together with cooler, had bend pins on cpu but never had pin snapped off.
this is master lvl 999+ :respect::respect:
:D
 
Is it because of the stock cooler being pita to remove or what?
 
The CPU works just fine leaving the pin where it is, and i have no idea why it snapped off - i ran cinebench to warm the paste up etc and had no issues... until i flipped it over and realised
I've taken to putting printed labels in the cases warning me to not remove the damn CPU's

When my new paste arrives i'ma actually do some temp testing, and probably lap my 3700x as well (keeping all its pins i hope)

Using half the clamshell casing for the CPU made this so much easier/safer for the pins
IMG_20200722_160533_exported_stabilized_3759875444160798813.gif
 
next time try to add some cotton (or some packing foam) on the bottom of the shell and then place cpu in it. this should prevent dust from sanding to go between pins and save you some time for cleaning.
 
The only thing i can think of is i got liquid metal next to the socket once on a previous mobo, both the 2700x and 1400 were used in that board. maybe some LM weakened the pins?
 
Back
Top