5000+ Blacky Overclocking

[DanishDevil]

That's probably not a huge deal. I would lap it, though. It will void your CPUs warranty.

 

[CrackerJack]

That's probably not a huge deal. I would lap it, though. It will void your CPUs warranty.

I still have a week for the warranty to go out. From newegg. I wait till then. And when i get the other one.

 

[CrackerJack]

so lapping is when you sand the heatsink and cpu down to the shinny copper or whatever it is. But making sure it's really smooth. Then put form or i've heard of glass too (but with water), in between the cpu and hs. Do you put thermal between the form and HS?

 

[Trigger911]

ooooh looks like a crack in the picture that could cause some heat problems the thermal paste will fill it up but thats just more heat being generated. and for the above don't put the Styrofoam in between the cpu and heat sink hehe. you push it down on the pins to protect them a bit. And a good lapping will show a big difference its the first thing i do after the warninty is up.

btw i found you a good read about lapping enjoy.
http://www.frostytech.com/articleview.cfm?articleID=82

 

[CrackerJack]

ooooh looks like a crack in the picture that could cause some heat problems the thermal paste will fill it up but thats just more heat being generated. and for the above don't put the Styrofoam in between the cpu and heat sink hehe. you push it down on the pins to protect them a bit. And a good lapping will show a big difference its the first thing i do after the warninty is up.

btw i found you a good read about lapping enjoy.
http://www.frostytech.com/articleview.cfm?articleID=82

What would cause that? Thats what got me!!

 

[Trigger911]

I think you did that when you installed the heat sink or might have when you removed it, also i seen this happen a few times, the scrach was there but you dont see it when its all new looking polished. after you get it a little dirty and warm it makes em stand out thats why o/c always lap the cpu and the heatsink.

Also a good guide for overclocking amd64 from a member here i followed it helped me get past a few problems.
http://forums.techpowerup.com/showt...t an exam now so ill be back in a hour or so.

 

[suraswami]

ha ha like I mentioned before you didn't install the heatsink properly on the cpu. You forced that damn big a.s cooler on top of the poor cpu and smashed it. You should be fined 10G for killing a beast LOL.

As far as TIM put a small drop (unboiled raw rice size) in the center of the IHS. Put your cpu cooler on top and try turning the cooler 1-2 degrees both sides. That should be enough. You don't need to take out to check if its settled properly. But the pain is the big as. cooler. Will not sit in one position until locked.

Hey my cheap CoolerMaster unlapped Vortex gives me good result.

You don't need to get a 6400 blacky but can get a 5600 like and OC the hell out of it.

 

[CrackerJack]

Well i got the new cpu today, i've got it in. And only put a dry rice size of compund in the center. But the HS on, then took it off to see the spread. It look good. So turn the power on and check the temps. 10 Times Better. Atleast the core temps are closer together. The other one was off by 10c-15c. And when I went to render my core 2 would get to hot and shut off. But anyway,

Thanks Guys

 

[cdawall]

start oc'ing i will post what i can get on mine when DD ships it

 

[CrackerJack]

start oc'ing i will post what i can get on mine when DD ships it

i thought i should wait atleast 200 hours. I didn't get the MX-2 or the other one. I just got the artic 5. i know, i should have got the other ones. But it was to late to change the order. Newegg it so damn fast. lol I didn't get a tracking number till today. And when i look at it, it was already in town. It comes from Memphis, So I get parts in 1 or 2 days. ( I only live about 3 1/2 hours away) Not in less it comes for Cal. then it's about a 3 or 4 days. Just with 3 day shipping.

 

[cdawall]

getting the best thermal paste is over rated i'm currently using some stuff that says intel P4 on it and that works fine, but then again seeing how hot p4s ran maybe this is better than MX-2

 

[CrackerJack]

Here's my temps from I started Adobe and when i started Rendering. You should be able to tell where i started rendering.

 

[cdawall]

Here's my temps from I started Adobe and when i started Rendering. You should be able to tell where i started rendering.

47C load temps pretty good

 

[CrackerJack]

47C load temps pretty good

Yeah but it would shut off at 50c. i check the max temps out on amd.com and it's 55c-something. (guess this is for both cores, or the cpu itself) In my bios i've got fan speed setting to max speed. None of that smart fan crap.

 

[cdawall]

Yeah but it would shut off at 50c. i check the max temps out on amd.com and it's 55c-something. (guess this is for both cores, or the cpu itself) In my bios i've got fan speed setting to max speed. None of that smart fan crap.

you can disable the shut down temp or set it higher for that matter and tcase max for that chip is 72C not 55C, 55C is the recommended max for those chips but failure point is @ 72C

http://www.amdgeeks.net/processor/ADO5000DSWOF/AMD-Athlon-64-X2-5000+

 

[CrackerJack]

you can disable the shut down temp or set it higher for that matter and tcase max for that chip is 72C not 55C, 55C is the recommended max for those chips but failure point is @ 72C

http://www.amdgeeks.net/processor/ADO5000DSWOF/AMD-Athlon-64-X2-5000+

humm thats cool i guess.

This is what I seen.
http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=40

Thanks for the right one!!

 

[cdawall]

humm thats cool i guess.

This is what I seen.
http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=40

Thanks for the right one!!

thats the higher vcore chip yours should be the lower vcore one that i posted

 

[Trigger911]

WOw been looking for this info lol thanks alot man

 

[erocker]

Heh, I just picked up a 5000+ BE and one of those new Ximatek coolers. I just need a damn case to put it in. I can't wait to do some AMD overclocking this weekend once more!!!

 

[Trigger911]

what do you guys run at cpu wise with loads?

i thought 50 was the max temp and is that with the ihs still?

 

[erocker]

I thought it was 65c? I know that was the case for 90mn AMD chips anyways. With all the AMD chips I've owned, I feel that under 45c idle is best (with max OC of course).

 

[Trigger911]

ok thanks for the info i giuess i gotta clock my 5000 be up gain w00t

 

[cdawall]

I thought it was 65c? I know that was the case for 90mn AMD chips anyways. With all the AMD chips I've owned, I feel that under 45c idle is best (with max OC of course).

most brisbane's are rated @72C

 

[l33tw00t]

http://valid.x86-secret.com/show_oc.php?id=339418

CPU Arch : 1 CPU - 2 Cores - 2 Threads
CPU PSN : AMD Athlon 64 X2 Dual Core Processor 5000+
CPU EXT : MMX(+) 3DNow!(+) SSE SSE2 SSE3 x86-64
CPUID : F.B.2 / Extended : F.6B
CPU Cache : L1 : 2 x 64 / 2 x 64 KB - L2 : 2 x 512 KB
Core : Brisbane (65 nm) / Stepping : BH-G2

Freq : 3237.48 MHz (249.04 * 13)
MB Brand : Asus
MB Model : M3A32-MVP DELUXE
NB : ATI RD790 rev 00
SB : ATI SB600 rev 00

GPU Type : ATI Radeon HD 3870 X2
GPU Clocks : Core 300 MHz / RAM 901 MHz
DirectX Version : 10.0

RAM : 4096 MB DDR2 Dual Channel
RAM Speed : 462.5 MHz (CPU/7) @ 5-5-5-18

idle temps 15,7
while ut3 29,28

 

[WarEagleAU]

someone on here had theres at 3.45ghz. I must achieve this!!!!