• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Ghetto modders club

how did you broke it?

I didn't 'friend' dropped it. -.-

With a SATA cable in it, and it was spinning lucky it didn't total the disk to be honest but then again its not my data [=


SpiriteH!
 
why do you have loose drives lying around?:laugh:
 
Not mine, all is good [= and ontop of that it reads and writes fine anyway, I did notice though when I turn the music up my sub disconnects the cable. I just wish I know this before I started cloning the disk -.- (what a waste of 2hours worth of power).


SpiriteH!
 
Not mine, all is good [= and ontop of that it reads and writes fine anyway, I did notice though when I turn the music up my sub disconnects the cable. I just wish I know this before I started cloning the disk -.- (what a waste of 2hours worth of power).


SpiriteH!

Sorry, I laughed :D
 
Here's my Ghetto mod the fan on my less than 1 yr old HD5770 died:shadedshu so out came an old PSU fan with low start V and low curent draw, replaced the power cable with the one from the HIS fan and away we went

025.JPG


the only good thing to come out of it is Lower temps at load and very quiet at idle
 
mode 2nd 12cm fan with my xigmatic dark night using just a double side tape

attachment.php
[/IMG]
 

Attachments

  • DSC01746.jpg
    DSC01746.jpg
    201.2 KB · Views: 1,604
Last edited:
as long as it stays on top it's fine it'll stay sitting there till the cows come home
 
nice work looks like that thing could have cut the heck outa tho but still good work whats the diff in performance over the stock cooler if I may ask.
 
nice work Dj-ElectriC, what fan do you have on it and how are temps on the 460?
 
Right now i have a stock gainward on it (not to be confused with the nice reference design with the copper heatpipes) witch is an absulute crap. i get around 93C on HEAVAN 2.0 loops so its kinda scary. im hoping that the S1 will block the temps to 43-45C. yeah... the S1 kicks ass. ATM i am waiting for screws that my friend sent me for this thing, cuz i dont have any.
 
Hello. I'm new on here.
I read the other ghetto thread,
http://www.techpowerup.com/forums/showthread.php?t=55387&page=22
but not this one. (I'm a little drunk, and I need to go to bed!)

I figured this was still the best place to ask about my next build.
GA-MA78LMT-US2H
phenom ii x2 550,
2gb corsiar 1333 ddr3,
heatsink from a junk pentium 4.(its not too bad, copper base, lots of fins)
I blew all my cash on the parts, so I need to find a zero cost cooling method.
Planning to fasten the unknown cooler master heatsink to my phenom with zip ties. Anyone have a better idea? It's only temporary until I find a new pump for my water cooling.

EDIT--- My chair keeps falling apart. Surely that counts as ghetto? :(
 
Last edited:
better idea: use the stock cooler
 
That would be a great idea if I had the stock cooler. I expect I won 't, as the guy never mentioned the cooler in the listing.
I bought the cpu from ebay, still waiting on bloody useless delivery company. I know the guy sent it because they tried to deliver it already. Instead of re-delivering like they should, my cpu has vanished. Joy. I supose I will get it eventually, but here begin's a quest that is almost certainly going to cost me money I can't afford. Bugger.
More annoyingly, the rest of the system is sat on my shelf, going out of date, waiting for a cpu.
:banghead::banghead::banghead::banghead::banghead:
 
Last edited:
my volt-modded GF3 with a socket 370 HSF and tornado fan:

attachment.php
 
bandsaw-cut heatsinks installed on Chrisray's 9700NP:

attachment.php
 
Add me please to club. This is my old Rage 128 pro, peltier+ watercool experiment. At the end condensate started to form near AGP slot:p

One question: Is it Ok to start new "Project" thread to show old projects in TPU?
 

Attachments

  • 2 Modded.jpg
    2 Modded.jpg
    203.4 KB · Views: 594
  • 3 Modded.jpg
    3 Modded.jpg
    199.9 KB · Views: 422
  • 4 Installedb.jpg
    4 Installedb.jpg
    187.1 KB · Views: 583
Is it Ok to start new "Project" thread to show old projects in TPU?

If there isn't already a thread by you on the same build, start one. The age of the components don't matter;)
 
another ghetto chipset cooler...



it's a E8400 stock block, i decided that stock chipset cooler was puny so i hacksawed this one and used screws to fit it. it fitted surprisingly clean, there's a low profile 80mm fan on it.

BTW, p35 can really heat it up! :twitch:
 
Back
Top