Neo Forza Faye DDR4-4600 2x 16 GB Review 16

Neo Forza Faye DDR4-4600 2x 16 GB Review

Value & Conclusion »

Tweaking for Speed

With testing out of the way, I endeavored to see if these sticks have any headroom. For Intel, I kept the same procedure I have been using, leaving all settings at their XMP defaults and then increasing the frequency until the system loses stability. After finding that limit, I manually tweaked for the maximum frequency and lowest possible timings. Voltage modification from stock is allowed. After all, this is overclocking!

A good starting point for Ryzen builds is 3600–4000 MT/s, it being optimal due to Infinity Fabric limitations. For those unaware, AMD Ryzen CPUs can in many applications benefit substantially from a 1:1 ratio being synchronized with the system memory and Infinity Fabric.

On the Intel side of things, 8th to 10th Generation Intel Core processors are going to benefit the most from the highest-possible frequency with the lowest timings. That being said, 3733–4000 MT/s is the ideal target range since there is no need to play around with VCCSA/IO voltages, and it is mostly plug and play. Switch to an 11th Gen Intel Core processor and things change given the introduction of the memory controller Gear ratio similar to what AMD has done. Once you surpass the memory controller's ability to stay in synchronous 1:1 mode, most motherboards will automatically switch to the 2:1 ratio. If all else fails, you can manually set this in the BIOS.

For the 11th Gen Intel Core i9-11900K used in this test system, the 1:1 ratio stops at a messy DDR4 3600. No matter the VCCSA/IO voltage or memory kit I use, this is the limit for this CPU. Any higher and I must switch to 2:1. Some have reported upwards of 4000 MT/s 1:1 support, but I am not one of the lucky few.

Now take all that information and throw it out the window. Yes, that is right. Unfortunately, most of that is only useful for single-rank memory. The main problem with the Neo Forza Faye DDR4-4600 kit is that it is dual-rank. in my testing, 1:1 ratio was not achievable above 3600 MT/s for either AMD or Intel. This memory is not optimal for AMD, and unlikely to be bootable above DDR4-4400 in the best setups without a lot of tweaking by trying hundreds of different combinations. To give you an idea of the time it can take, I spent 6 hours trying different settings on the AMD platform.

This memory will best-suit 11th Gen Intel Rocket Lake processors, and Gear Ratio 2:1 will have to be enabled. My recommendation is to start with 3600 MT/s by manually typing in all the values and increasing the speeds as you go. You will need to pump the VCCSA and VCCIO/2 voltages a bit. 1.3 V is a good starting point and may need to be increased as you approach 4800 MT/s.

Intel Results


With the Intel Core i9-11900K, I was able to achieve 2400 MHz with all other XMP settings at their default, which is absolutely amazing. It shows that Neo Forza binned this kit well, and it has some headroom. Unfortunately, because of the extreme nature of this memory kit, the MSI Z590 ACE has a hard time with any kit above this frequency—it is not the maximum frequency this kit can achieve. Even with a brief stint of 1.65 V, I could not lower the CAS value without errors, so this was the end of the overclock for me.

I believe DDR4-5000 is possible for those willing to spend the hours it requires to tune the memory settings correctly; maybe with a bit of a luck and a better motherboard, like the ASUS Z590 APEX or EVGA Z590 Dark.




AMD Results


For AMD, I could not go above 2200 MHz on my MSI MEG B550 Unify-X with the XMP default timings. I decided to go down and try for the tightest timings and 1:1 ratio. This memory does not disappoint for Hynix memory. However, better timings and cheaper solutions exist for DDR4-3600. It was fun to play with the memory and see what I could accomplish. Hynix ICs do not scale down as well as up. Even with 1.65 V going into the memory, errors would appear below CAS 16. Therefore, I stuck with 1.5 V, and I didn't put much effort into the rest of the values; they can probably be a bit lower.


Next Page »Value & Conclusion
View as single page
Nov 18th, 2026 04:45 CST change timezone

New Forum Posts

Popular Reviews

TPU on YouTube

Controversial News Posts